Services
Service Areas
Shattered Back Window on Fiat 124 Spider: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Fiat 124 Spider: Safety, Visibility, and Securing the Vehicle
A shattered rear window on your Fiat 124 Spider is urgent, but the right steps prevent injuries and limit secondary damage. If the glass breaks while driving, slow down gradually, activate hazard lights, and park in a safe spot away from traffic. Do not sweep glass with bare hands. Tempered back glass breaks into small pellets that can cling to clothing and hide in seat seams, so keep passengers from leaning into the opening and keep kids and pets out until cleanup is underway. If you must move the vehicle, clear the rear deck so pieces do not slide forward under braking. Remove any loose chunks hanging in the frame, but leave stubborn fragments for the installer. Then cover the opening from the outside with plastic sheeting and painter's tape to reduce water intrusion and deter theft. Avoid slamming doors or closing all windows with high HVAC pressure, since pressure pulses can pop remaining shards free. Take photos for your insurance claim; comprehensive coverage often applies to rear glass. Bang AutoGlass can then complete mobile Fiat 124 Spider back glass replacement, often as soon as next day. Installation typically takes 30-45 minutes, followed by at least 1 hour of urethane cure time, and every job includes our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A shattered rear window spreads sharp fragments through your Fiat 124 Spider, so handle cleanup like a controlled detail job. Start with PPE: closed-toe shoes, thick gloves, and eye protection. Keep passengers out of the cabin. If possible, drape plastic sheeting over seats, the rear deck/parcel shelf, and the cargo area before you move glass so shards do not get ground into fabric. Remove the largest pieces first. Lift chunks from the frame and rear deck by hand and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong household vacuum and a crevice tool. Work top-down in a repeatable route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk or cargo well, including the spare-tire compartment. After vacuuming, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from upholstery and corners; repeat until the tape comes back clean. Finish with gentle vacuum passes and a slightly damp microfiber towel on plastics to avoid scratches. Leave the opening accessible so a mobile rear window replacement can be installed cleanly and securely.
Confirm the Correct Rear Glass for Fiat 124 Spider: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Before you replace the rear window on a Fiat 124 Spider, confirm which back glass the vehicle needs. VIN validation or a parts lookup is the safest method because option differences change the glass. Start with the rear defroster: the replacement must include the correct heating grid and the proper terminal tabs so the factory connectors attach securely. Also verify antenna features. Many vehicles embed AM/FM, GPS, or cellular traces in the rear glass; if your reception relied on those lines, choose an antenna-equipped replacement. Tint matching matters as well. Rear glass may be clear, lightly tinted, or privacy glass with a darker factory shade. Matching tint supports a uniform look, better heat rejection, and local compliance. If your Fiat 124 Spider had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after installation. Finally, verify the certification stamp. Automotive glass includes DOT identification and AS markings (AS2/AS3 are common on rear/side glass and can indicate tinted variations). Correct markings and the part number help ensure proper curvature and tempered-glass performance. Bang AutoGlass verifies these details before mobile dispatch and backs every install with our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
Removal and preparation are the foundation of a leak-free rear window replacement on your Fiat 124 Spider. We start with containment: seats, the rear deck, and the cargo area are covered so glass pellets and adhesive debris don't contaminate the interior. Trim, fasteners, and moldings are removed in the proper sequence to protect clips and keep the opening accessible, and defroster/antenna leads are secured so wiring isn't strained. Next, the old urethane is cut and reduced to create a stable bonding surface. Standard methods remove most cured adhesive while leaving an even base layer (about 1-2 mm) so new urethane bonds to existing urethane rather than bare metal. We inspect the pinchweld for scratches through paint, rust, contamination, or misalignment from prior repairs, then treat, prime, and seal any exposed metal because corrosion under the bond line can cause leaks and adhesion loss. Before installation, we dry-fit the replacement rear glass for your Fiat 124 Spider, confirm molding and spacer condition, clean the frit and aperture, and apply the correct primer/activator with proper flash times. This prep discipline lets Bang AutoGlass set the glass evenly and deliver mobile, next-day rear glass replacement backed by a lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Fiat 124 Spider: What Controls Safe Release
The difference between "installed" and "safe" after a Fiat 124 Spider rear window replacement is urethane curing. Auto glass urethane is a moisture-curing polyurethane adhesive, and each system includes Safe Drive-Away Time (SDAT) guidance tied to minimum bond strength. SDAT is controlled by the adhesive used, proper surface prep, bead size/shape, and environmental conditions like temperature and humidity. Cold or very dry air can slow cure; warm, humid conditions typically speed it up. Open-time limits also matter-urethane must be applied and the glass set within the specified window for proper wet-out and adhesion. Prep details directly affect the bond: clean, contaminant-free surfaces; correct primer/activator application; and required flash times. The urethane bead must be continuous and uniform so it compresses evenly around the perimeter, preventing thin spots that can leak or whistle. Exposed metal on the pinchweld must be protected and primed because corrosion under the bond line is a common long-term failure point. At Bang AutoGlass, most Fiat 124 Spider back glass replacements take about 30-45 minutes on site, then we require at least 1 hour before safe drive-away. Drive gently, avoid slamming doors, and skip automated car washes; we'll extend cure time if conditions warrant it, backed by our lifetime workmanship warranty and help with comprehensive coverage claims.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Fiat 124 Spider rear window replacement is installed, verification confirms the glass is correct, sealed, and functional. First, check electrical features: rear defroster connectors should be firmly seated on the tabs, and any in-glass antenna leads should be reconnected and strain-relieved so hatch or trunk movement won't tug the wiring. A quick function check helps you avoid discovering a loose connection or weak reception later. Next, validate sealing and wind noise. The molding and reveal line should be even, with consistent spacing around the perimeter. We perform a controlled perimeter water test to confirm there are no leaks, and when practical a short road test to replicate highway airflow; a whistle usually points to a small gap or mis-seated molding. As a simple owner check after rain, look for damp headliner edges or moisture in the cargo area. Finally, keep documentation: you should receive an invoice, warranty record, and notes on the rear glass installed for your Fiat 124 Spider (tint, defroster grid, antenna integration, and DOT/AS markings). Bang AutoGlass backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Services
Service Areas
Shattered Back Window on Fiat 124 Spider: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Fiat 124 Spider: Safety, Visibility, and Securing the Vehicle
A shattered rear window on your Fiat 124 Spider is urgent, but the right steps prevent injuries and limit secondary damage. If the glass breaks while driving, slow down gradually, activate hazard lights, and park in a safe spot away from traffic. Do not sweep glass with bare hands. Tempered back glass breaks into small pellets that can cling to clothing and hide in seat seams, so keep passengers from leaning into the opening and keep kids and pets out until cleanup is underway. If you must move the vehicle, clear the rear deck so pieces do not slide forward under braking. Remove any loose chunks hanging in the frame, but leave stubborn fragments for the installer. Then cover the opening from the outside with plastic sheeting and painter's tape to reduce water intrusion and deter theft. Avoid slamming doors or closing all windows with high HVAC pressure, since pressure pulses can pop remaining shards free. Take photos for your insurance claim; comprehensive coverage often applies to rear glass. Bang AutoGlass can then complete mobile Fiat 124 Spider back glass replacement, often as soon as next day. Installation typically takes 30-45 minutes, followed by at least 1 hour of urethane cure time, and every job includes our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A shattered rear window spreads sharp fragments through your Fiat 124 Spider, so handle cleanup like a controlled detail job. Start with PPE: closed-toe shoes, thick gloves, and eye protection. Keep passengers out of the cabin. If possible, drape plastic sheeting over seats, the rear deck/parcel shelf, and the cargo area before you move glass so shards do not get ground into fabric. Remove the largest pieces first. Lift chunks from the frame and rear deck by hand and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong household vacuum and a crevice tool. Work top-down in a repeatable route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk or cargo well, including the spare-tire compartment. After vacuuming, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from upholstery and corners; repeat until the tape comes back clean. Finish with gentle vacuum passes and a slightly damp microfiber towel on plastics to avoid scratches. Leave the opening accessible so a mobile rear window replacement can be installed cleanly and securely.
Confirm the Correct Rear Glass for Fiat 124 Spider: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Before you replace the rear window on a Fiat 124 Spider, confirm which back glass the vehicle needs. VIN validation or a parts lookup is the safest method because option differences change the glass. Start with the rear defroster: the replacement must include the correct heating grid and the proper terminal tabs so the factory connectors attach securely. Also verify antenna features. Many vehicles embed AM/FM, GPS, or cellular traces in the rear glass; if your reception relied on those lines, choose an antenna-equipped replacement. Tint matching matters as well. Rear glass may be clear, lightly tinted, or privacy glass with a darker factory shade. Matching tint supports a uniform look, better heat rejection, and local compliance. If your Fiat 124 Spider had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after installation. Finally, verify the certification stamp. Automotive glass includes DOT identification and AS markings (AS2/AS3 are common on rear/side glass and can indicate tinted variations). Correct markings and the part number help ensure proper curvature and tempered-glass performance. Bang AutoGlass verifies these details before mobile dispatch and backs every install with our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
Removal and preparation are the foundation of a leak-free rear window replacement on your Fiat 124 Spider. We start with containment: seats, the rear deck, and the cargo area are covered so glass pellets and adhesive debris don't contaminate the interior. Trim, fasteners, and moldings are removed in the proper sequence to protect clips and keep the opening accessible, and defroster/antenna leads are secured so wiring isn't strained. Next, the old urethane is cut and reduced to create a stable bonding surface. Standard methods remove most cured adhesive while leaving an even base layer (about 1-2 mm) so new urethane bonds to existing urethane rather than bare metal. We inspect the pinchweld for scratches through paint, rust, contamination, or misalignment from prior repairs, then treat, prime, and seal any exposed metal because corrosion under the bond line can cause leaks and adhesion loss. Before installation, we dry-fit the replacement rear glass for your Fiat 124 Spider, confirm molding and spacer condition, clean the frit and aperture, and apply the correct primer/activator with proper flash times. This prep discipline lets Bang AutoGlass set the glass evenly and deliver mobile, next-day rear glass replacement backed by a lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Fiat 124 Spider: What Controls Safe Release
The difference between "installed" and "safe" after a Fiat 124 Spider rear window replacement is urethane curing. Auto glass urethane is a moisture-curing polyurethane adhesive, and each system includes Safe Drive-Away Time (SDAT) guidance tied to minimum bond strength. SDAT is controlled by the adhesive used, proper surface prep, bead size/shape, and environmental conditions like temperature and humidity. Cold or very dry air can slow cure; warm, humid conditions typically speed it up. Open-time limits also matter-urethane must be applied and the glass set within the specified window for proper wet-out and adhesion. Prep details directly affect the bond: clean, contaminant-free surfaces; correct primer/activator application; and required flash times. The urethane bead must be continuous and uniform so it compresses evenly around the perimeter, preventing thin spots that can leak or whistle. Exposed metal on the pinchweld must be protected and primed because corrosion under the bond line is a common long-term failure point. At Bang AutoGlass, most Fiat 124 Spider back glass replacements take about 30-45 minutes on site, then we require at least 1 hour before safe drive-away. Drive gently, avoid slamming doors, and skip automated car washes; we'll extend cure time if conditions warrant it, backed by our lifetime workmanship warranty and help with comprehensive coverage claims.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Fiat 124 Spider rear window replacement is installed, verification confirms the glass is correct, sealed, and functional. First, check electrical features: rear defroster connectors should be firmly seated on the tabs, and any in-glass antenna leads should be reconnected and strain-relieved so hatch or trunk movement won't tug the wiring. A quick function check helps you avoid discovering a loose connection or weak reception later. Next, validate sealing and wind noise. The molding and reveal line should be even, with consistent spacing around the perimeter. We perform a controlled perimeter water test to confirm there are no leaks, and when practical a short road test to replicate highway airflow; a whistle usually points to a small gap or mis-seated molding. As a simple owner check after rain, look for damp headliner edges or moisture in the cargo area. Finally, keep documentation: you should receive an invoice, warranty record, and notes on the rear glass installed for your Fiat 124 Spider (tint, defroster grid, antenna integration, and DOT/AS markings). Bang AutoGlass backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Services
Service Areas
Shattered Back Window on Fiat 124 Spider: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Fiat 124 Spider: Safety, Visibility, and Securing the Vehicle
A shattered rear window on your Fiat 124 Spider is urgent, but the right steps prevent injuries and limit secondary damage. If the glass breaks while driving, slow down gradually, activate hazard lights, and park in a safe spot away from traffic. Do not sweep glass with bare hands. Tempered back glass breaks into small pellets that can cling to clothing and hide in seat seams, so keep passengers from leaning into the opening and keep kids and pets out until cleanup is underway. If you must move the vehicle, clear the rear deck so pieces do not slide forward under braking. Remove any loose chunks hanging in the frame, but leave stubborn fragments for the installer. Then cover the opening from the outside with plastic sheeting and painter's tape to reduce water intrusion and deter theft. Avoid slamming doors or closing all windows with high HVAC pressure, since pressure pulses can pop remaining shards free. Take photos for your insurance claim; comprehensive coverage often applies to rear glass. Bang AutoGlass can then complete mobile Fiat 124 Spider back glass replacement, often as soon as next day. Installation typically takes 30-45 minutes, followed by at least 1 hour of urethane cure time, and every job includes our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A shattered rear window spreads sharp fragments through your Fiat 124 Spider, so handle cleanup like a controlled detail job. Start with PPE: closed-toe shoes, thick gloves, and eye protection. Keep passengers out of the cabin. If possible, drape plastic sheeting over seats, the rear deck/parcel shelf, and the cargo area before you move glass so shards do not get ground into fabric. Remove the largest pieces first. Lift chunks from the frame and rear deck by hand and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong household vacuum and a crevice tool. Work top-down in a repeatable route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk or cargo well, including the spare-tire compartment. After vacuuming, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from upholstery and corners; repeat until the tape comes back clean. Finish with gentle vacuum passes and a slightly damp microfiber towel on plastics to avoid scratches. Leave the opening accessible so a mobile rear window replacement can be installed cleanly and securely.
Confirm the Correct Rear Glass for Fiat 124 Spider: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Before you replace the rear window on a Fiat 124 Spider, confirm which back glass the vehicle needs. VIN validation or a parts lookup is the safest method because option differences change the glass. Start with the rear defroster: the replacement must include the correct heating grid and the proper terminal tabs so the factory connectors attach securely. Also verify antenna features. Many vehicles embed AM/FM, GPS, or cellular traces in the rear glass; if your reception relied on those lines, choose an antenna-equipped replacement. Tint matching matters as well. Rear glass may be clear, lightly tinted, or privacy glass with a darker factory shade. Matching tint supports a uniform look, better heat rejection, and local compliance. If your Fiat 124 Spider had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after installation. Finally, verify the certification stamp. Automotive glass includes DOT identification and AS markings (AS2/AS3 are common on rear/side glass and can indicate tinted variations). Correct markings and the part number help ensure proper curvature and tempered-glass performance. Bang AutoGlass verifies these details before mobile dispatch and backs every install with our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
Removal and preparation are the foundation of a leak-free rear window replacement on your Fiat 124 Spider. We start with containment: seats, the rear deck, and the cargo area are covered so glass pellets and adhesive debris don't contaminate the interior. Trim, fasteners, and moldings are removed in the proper sequence to protect clips and keep the opening accessible, and defroster/antenna leads are secured so wiring isn't strained. Next, the old urethane is cut and reduced to create a stable bonding surface. Standard methods remove most cured adhesive while leaving an even base layer (about 1-2 mm) so new urethane bonds to existing urethane rather than bare metal. We inspect the pinchweld for scratches through paint, rust, contamination, or misalignment from prior repairs, then treat, prime, and seal any exposed metal because corrosion under the bond line can cause leaks and adhesion loss. Before installation, we dry-fit the replacement rear glass for your Fiat 124 Spider, confirm molding and spacer condition, clean the frit and aperture, and apply the correct primer/activator with proper flash times. This prep discipline lets Bang AutoGlass set the glass evenly and deliver mobile, next-day rear glass replacement backed by a lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Fiat 124 Spider: What Controls Safe Release
The difference between "installed" and "safe" after a Fiat 124 Spider rear window replacement is urethane curing. Auto glass urethane is a moisture-curing polyurethane adhesive, and each system includes Safe Drive-Away Time (SDAT) guidance tied to minimum bond strength. SDAT is controlled by the adhesive used, proper surface prep, bead size/shape, and environmental conditions like temperature and humidity. Cold or very dry air can slow cure; warm, humid conditions typically speed it up. Open-time limits also matter-urethane must be applied and the glass set within the specified window for proper wet-out and adhesion. Prep details directly affect the bond: clean, contaminant-free surfaces; correct primer/activator application; and required flash times. The urethane bead must be continuous and uniform so it compresses evenly around the perimeter, preventing thin spots that can leak or whistle. Exposed metal on the pinchweld must be protected and primed because corrosion under the bond line is a common long-term failure point. At Bang AutoGlass, most Fiat 124 Spider back glass replacements take about 30-45 minutes on site, then we require at least 1 hour before safe drive-away. Drive gently, avoid slamming doors, and skip automated car washes; we'll extend cure time if conditions warrant it, backed by our lifetime workmanship warranty and help with comprehensive coverage claims.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Fiat 124 Spider rear window replacement is installed, verification confirms the glass is correct, sealed, and functional. First, check electrical features: rear defroster connectors should be firmly seated on the tabs, and any in-glass antenna leads should be reconnected and strain-relieved so hatch or trunk movement won't tug the wiring. A quick function check helps you avoid discovering a loose connection or weak reception later. Next, validate sealing and wind noise. The molding and reveal line should be even, with consistent spacing around the perimeter. We perform a controlled perimeter water test to confirm there are no leaks, and when practical a short road test to replicate highway airflow; a whistle usually points to a small gap or mis-seated molding. As a simple owner check after rain, look for damp headliner edges or moisture in the cargo area. Finally, keep documentation: you should receive an invoice, warranty record, and notes on the rear glass installed for your Fiat 124 Spider (tint, defroster grid, antenna integration, and DOT/AS markings). Bang AutoGlass backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Enjoy More Relevant Blogs
Tempered vs Laminated Door Glass on Dodge Ram 2500 Regular Cab: What’s Used and Why It Matters
Tempered vs laminated door glass on Dodge Ram 2500 Regular Cab: what your vehicle uses, how it breaks, and what it means for replacement safety, cost, and cleanup.
How to Schedule ADAS Calibration for Ford F250 Super Duty Crew Cab After Windshield Replacement
Schedule ADAS calibration for Ford F250 Super Duty Crew Cab after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
After a Break-In: Dodge Challenger Quarter Glass Replacement Plan to Restore Security and Visibility
After a break-in on Dodge Challenger, restore security with a quarter glass replacement plan: cleanup, temporary protection, scheduling, and post-install checks.
Will Insurance Cover Door Glass Replacement for a Ford Focus RS? Claims Steps, Deductibles, and What to Document
Will insurance cover Ford Focus RS door glass replacement? Learn claim steps, deductibles, photos to document, and how to schedule fast repairs today.
ADAS After Windshield Replacement on Gmc Terrain: Calibration Basics and Safety Checks
ADAS after Gmc Terrain windshield replacement: calibration basics, common safety checks, and how to confirm cameras and sensors are working correctly.
How to Schedule Mobile Rear Glass Replacement for Gmc Rally Wagon 2500
Schedule mobile rear glass replacement for your Gmc Rally Wagon 2500 in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Stop Leaks and Wind Noise: What Proper Dodge Durango Quarter Glass Replacement Should Prevent
Stop leaks and wind noise with proper Dodge Durango quarter glass replacement. Learn what correct fit, sealing, and trim should prevent after install.
Tempered Safety Rear Glass Replacement for Gmc Canyon Crew Cab: Understanding DOT Markings and FMVSS 205
Need Gmc Canyon Crew Cab rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Post-Install Checks for Gmc Sierra (Classic) 1500 Extended Cab: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Gmc Sierra (Classic) 1500 Extended Cab: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Fast Scheduling Guide: Gmc Sierra 3500 Hd Extended Cab Windshield Replacement From Booking to Install
Book Gmc Sierra 3500 Hd Extended Cab windshield replacement fast. See scheduling steps, what to prep, install timing, and when you can safely drive away. Get a quote today.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm