Services
Service Areas
OEM-Quality Sunroof Glass Replacement for Ford Expedition El: DOT Markings and FMVSS 205 Explained
What FMVSS 205 Means for Ford Expedition El Sunroof and Panoramic Roof Glass
FMVSS 205 (49 CFR 571.205) is the federal baseline for automotive safety glazing, covering sunroof and panoramic roof glass on your Ford Expedition El. The rule incorporates ANSI/SAE Z26.1, so compliant glass must meet defined test categories and display specific etched certification marks. This framework exists to ensure roof glass maintains usable optical clarity, tolerates temperature swings and moisture, and breaks in a known, safety-oriented manner. For Ford Expedition El sunroof glass replacement, OEM-quality starts with matching what the factory installed. The correct panel should match the original build (tempered or laminated), carry the proper AS classification for roof placement, and show valid DOT/AS markings indicating it was produced and labeled under FMVSS 205. When those identifiers line up, you are far more likely to get the right tint tone, thickness, edge finish, and bonding surface details that support proper sealing and sunroof operation. Bang AutoGlass photographs your existing roof-glass stamp, verifies the markings, and sources an FMVSS-compliant OEM-quality match before scheduling mobile service—often next day. Most installs take 30–45 minutes; allow about an hour of cure time where bonding applies. We back our work with a lifetime workmanship warranty and coordinate with all insurers when comprehensive coverage applies.
How to Read the Sunroof Glass Stamp: DOT Symbol, Manufacturer Code, and Required Marks
The stamp etched into your Ford Expedition El sunroof or panoramic roof glass functions as its compliance label. Knowing what it means helps you verify you are comparing like-for-like parts and strengthens documentation for a claim. Start with the “DOT” marking. Under FMVSS 205, prime glazing manufacturers add DOT plus a manufacturer number assigned by NHTSA, linking the panel to the company that certified it as U.S. motor-vehicle safety glazing. Then confirm the AS classification (AS1, AS2, AS3, etc.) from ANSI/SAE Z26.1. These codes align with tested performance requirements and allowable installation locations. Windshields are often AS1, while Ford Expedition El roof panels are commonly AS2 or AS3 depending on factory tint and design. Many stamps also call out construction—“TEMPERED” or “LAMINATED”—and may include a logo, an “M” model code, production date/batch symbols, and indicators for coatings or privacy tint. You might also see international approvals like an “E” mark with “43R” (UNECE R43). That can be legitimate, but the replacement should still match your original DOT/AS details, tint cues, and construction. Bang AutoGlass photographs the stamp, verifies the markings, and sources an OEM-quality match through mobile service.
AS Ratings and Safety Glazing Types: What the Markings Indicate for Roof Glass
On your Ford Expedition El, the “AS” code etched on the sunroof or panoramic roof glass is the safety-glazing classification from ANSI/SAE Z26.1, which FMVSS 205 incorporates. AS codes indicate the performance category the glass was tested to and where it is intended to be installed. AS1 is typically used for windshields because it aligns with stricter optical and light-transmission requirements, while roof glass is commonly marked AS2 or AS3 based on vehicle design and factory tint. The stamp also identifies construction. Tempered safety glass is heat-treated and usually fractures into many small pieces to reduce sharp shards. Laminated safety glass uses an interlayer that helps retain fragments; depending on the build, it can improve retention, reduce noise, and support UV or solar-control features. Because roof systems vary by trim and model year, OEM-quality Ford Expedition El roof-glass replacement means matching the original construction and markings, not guessing. Why it matters: AS rating, tint category, and glass type affect glare, heat rejection, break behavior, and overall compliance. Bang AutoGlass verifies the AS code and whether the panel is tempered or laminated, then sources an OEM-quality, FMVSS 205-compliant match for your Ford Expedition El sunroof or panoramic roof replacement.
OEM-Quality Match for Ford Expedition El: Tint, Coatings, Hardware, and Sensor Compatibility
An OEM-quality match for Ford Expedition El roof glass means the panel looks and performs like the factory part. Sunroof and panoramic roof panels are engineered to a specific curvature, thickness, and tint tone, and many include UV filtration and solar-control coatings that reduce infrared heat while maintaining clarity. If replacement glass is not built to the same spec, the difference can be obvious: a slightly different color in sunlight, a two-tone roof, or changed heat rejection on bright days. Perimeter details are functional, not cosmetic. The ceramic frit band and dot matrix create a uniform bonding surface, protect urethane from UV exposure, and conceal the bond line and trim for an OEM finish. Roof glass can also include encapsulation, polished edges, brackets, and locating features that set panel height and determine how seals compress and how wind noise is managed at speed. On many Ford Expedition El configurations, those interfaces must match so the tilt/slide mechanism and sunshade move smoothly. Bang AutoGlass verifies the stamp, DOT markings, and key fitment features, then sources a verified OEM-quality match for your Ford Expedition El. Our fully mobile service can often perform roof glass replacement as soon as next day, backed by a lifetime workmanship warranty.
Installation Standards That Protect the Result: Bond Prep, Adhesive Choice, and AGRSS Best Practices
The difference between installed and installed correctly is process control. For Ford Expedition El sunroof and panoramic roof glass, installation standards prevent leaks, wind noise, rattles, and premature seal failure. A high-quality panel still depends on correct removal technique, meticulous surface preparation, and the adhesive or mechanical retention method specified for the roof system. We protect the cabin, remove the damaged panel safely, and inspect the aperture, seals, and mounting points so the replacement can sit at the proper OEM height. Surface prep is mandatory. The bond area must be clean, dry, and free of oils, glass dust, and residue that reduce adhesion. Where urethane bonding is used, old urethane is managed to a uniform, stable base as appropriate, and any bare metal or corrosion is treated so the adhesive has a reliable substrate. When required, we apply the correct activator and primer sequence to ensure compatible chemical bonding and UV protection at the bond line. Adhesive handling matters too; automotive urethanes cure predictably only when used per spec. AGRSS provides a benchmark for safe removal, proper prep, adhesive handling, and verification. Bang AutoGlass follows these best practices on every mobile roof-glass job and provides aftercare guidance, including recommended cure time before drive-away, often at least one hour when bonding applies.
Post-Install Verification: Fit, Leak/Wind Noise Checks, and Documentation for Ford Expedition El
A professional Ford Expedition El sunroof glass replacement is not complete until post-install verification is done. These checks prevent common complaints: sunroof leaks, wind noise, rattles, and "won't close" issues. First, we confirm fit and finish. The panel should sit flush to the roofline with even gaps, proper seal compression, and clean alignment with trim, moldings, and the sunshade track. Mounts, locating tabs, and fasteners are rechecked so the glass is not sitting high, low, or twisted. Next, we test operation. We cycle the sunroof and sunshade through vent, open, close, and any express functions to confirm smooth travel and correct stop points. Many roof systems require initialization or a teach procedure after service so the motor learns limits and anti-pinch behavior; completing it helps prevent false reversals or incomplete closing. Then we validate sealing and water management. Because sunroofs route water through a tray and drain tubes, we perform a controlled water test to confirm proper routing and drainage rather than pooling. When appropriate, we add a brief road-speed wind-noise check. Finally, we document the service, provide aftercare guidance (including cure time), coordinate with insurance when comprehensive coverage applies, and back the work with a lifetime workmanship warranty.
Services
Service Areas
OEM-Quality Sunroof Glass Replacement for Ford Expedition El: DOT Markings and FMVSS 205 Explained
What FMVSS 205 Means for Ford Expedition El Sunroof and Panoramic Roof Glass
FMVSS 205 (49 CFR 571.205) is the federal baseline for automotive safety glazing, covering sunroof and panoramic roof glass on your Ford Expedition El. The rule incorporates ANSI/SAE Z26.1, so compliant glass must meet defined test categories and display specific etched certification marks. This framework exists to ensure roof glass maintains usable optical clarity, tolerates temperature swings and moisture, and breaks in a known, safety-oriented manner. For Ford Expedition El sunroof glass replacement, OEM-quality starts with matching what the factory installed. The correct panel should match the original build (tempered or laminated), carry the proper AS classification for roof placement, and show valid DOT/AS markings indicating it was produced and labeled under FMVSS 205. When those identifiers line up, you are far more likely to get the right tint tone, thickness, edge finish, and bonding surface details that support proper sealing and sunroof operation. Bang AutoGlass photographs your existing roof-glass stamp, verifies the markings, and sources an FMVSS-compliant OEM-quality match before scheduling mobile service—often next day. Most installs take 30–45 minutes; allow about an hour of cure time where bonding applies. We back our work with a lifetime workmanship warranty and coordinate with all insurers when comprehensive coverage applies.
How to Read the Sunroof Glass Stamp: DOT Symbol, Manufacturer Code, and Required Marks
The stamp etched into your Ford Expedition El sunroof or panoramic roof glass functions as its compliance label. Knowing what it means helps you verify you are comparing like-for-like parts and strengthens documentation for a claim. Start with the “DOT” marking. Under FMVSS 205, prime glazing manufacturers add DOT plus a manufacturer number assigned by NHTSA, linking the panel to the company that certified it as U.S. motor-vehicle safety glazing. Then confirm the AS classification (AS1, AS2, AS3, etc.) from ANSI/SAE Z26.1. These codes align with tested performance requirements and allowable installation locations. Windshields are often AS1, while Ford Expedition El roof panels are commonly AS2 or AS3 depending on factory tint and design. Many stamps also call out construction—“TEMPERED” or “LAMINATED”—and may include a logo, an “M” model code, production date/batch symbols, and indicators for coatings or privacy tint. You might also see international approvals like an “E” mark with “43R” (UNECE R43). That can be legitimate, but the replacement should still match your original DOT/AS details, tint cues, and construction. Bang AutoGlass photographs the stamp, verifies the markings, and sources an OEM-quality match through mobile service.
AS Ratings and Safety Glazing Types: What the Markings Indicate for Roof Glass
On your Ford Expedition El, the “AS” code etched on the sunroof or panoramic roof glass is the safety-glazing classification from ANSI/SAE Z26.1, which FMVSS 205 incorporates. AS codes indicate the performance category the glass was tested to and where it is intended to be installed. AS1 is typically used for windshields because it aligns with stricter optical and light-transmission requirements, while roof glass is commonly marked AS2 or AS3 based on vehicle design and factory tint. The stamp also identifies construction. Tempered safety glass is heat-treated and usually fractures into many small pieces to reduce sharp shards. Laminated safety glass uses an interlayer that helps retain fragments; depending on the build, it can improve retention, reduce noise, and support UV or solar-control features. Because roof systems vary by trim and model year, OEM-quality Ford Expedition El roof-glass replacement means matching the original construction and markings, not guessing. Why it matters: AS rating, tint category, and glass type affect glare, heat rejection, break behavior, and overall compliance. Bang AutoGlass verifies the AS code and whether the panel is tempered or laminated, then sources an OEM-quality, FMVSS 205-compliant match for your Ford Expedition El sunroof or panoramic roof replacement.
OEM-Quality Match for Ford Expedition El: Tint, Coatings, Hardware, and Sensor Compatibility
An OEM-quality match for Ford Expedition El roof glass means the panel looks and performs like the factory part. Sunroof and panoramic roof panels are engineered to a specific curvature, thickness, and tint tone, and many include UV filtration and solar-control coatings that reduce infrared heat while maintaining clarity. If replacement glass is not built to the same spec, the difference can be obvious: a slightly different color in sunlight, a two-tone roof, or changed heat rejection on bright days. Perimeter details are functional, not cosmetic. The ceramic frit band and dot matrix create a uniform bonding surface, protect urethane from UV exposure, and conceal the bond line and trim for an OEM finish. Roof glass can also include encapsulation, polished edges, brackets, and locating features that set panel height and determine how seals compress and how wind noise is managed at speed. On many Ford Expedition El configurations, those interfaces must match so the tilt/slide mechanism and sunshade move smoothly. Bang AutoGlass verifies the stamp, DOT markings, and key fitment features, then sources a verified OEM-quality match for your Ford Expedition El. Our fully mobile service can often perform roof glass replacement as soon as next day, backed by a lifetime workmanship warranty.
Installation Standards That Protect the Result: Bond Prep, Adhesive Choice, and AGRSS Best Practices
The difference between installed and installed correctly is process control. For Ford Expedition El sunroof and panoramic roof glass, installation standards prevent leaks, wind noise, rattles, and premature seal failure. A high-quality panel still depends on correct removal technique, meticulous surface preparation, and the adhesive or mechanical retention method specified for the roof system. We protect the cabin, remove the damaged panel safely, and inspect the aperture, seals, and mounting points so the replacement can sit at the proper OEM height. Surface prep is mandatory. The bond area must be clean, dry, and free of oils, glass dust, and residue that reduce adhesion. Where urethane bonding is used, old urethane is managed to a uniform, stable base as appropriate, and any bare metal or corrosion is treated so the adhesive has a reliable substrate. When required, we apply the correct activator and primer sequence to ensure compatible chemical bonding and UV protection at the bond line. Adhesive handling matters too; automotive urethanes cure predictably only when used per spec. AGRSS provides a benchmark for safe removal, proper prep, adhesive handling, and verification. Bang AutoGlass follows these best practices on every mobile roof-glass job and provides aftercare guidance, including recommended cure time before drive-away, often at least one hour when bonding applies.
Post-Install Verification: Fit, Leak/Wind Noise Checks, and Documentation for Ford Expedition El
A professional Ford Expedition El sunroof glass replacement is not complete until post-install verification is done. These checks prevent common complaints: sunroof leaks, wind noise, rattles, and "won't close" issues. First, we confirm fit and finish. The panel should sit flush to the roofline with even gaps, proper seal compression, and clean alignment with trim, moldings, and the sunshade track. Mounts, locating tabs, and fasteners are rechecked so the glass is not sitting high, low, or twisted. Next, we test operation. We cycle the sunroof and sunshade through vent, open, close, and any express functions to confirm smooth travel and correct stop points. Many roof systems require initialization or a teach procedure after service so the motor learns limits and anti-pinch behavior; completing it helps prevent false reversals or incomplete closing. Then we validate sealing and water management. Because sunroofs route water through a tray and drain tubes, we perform a controlled water test to confirm proper routing and drainage rather than pooling. When appropriate, we add a brief road-speed wind-noise check. Finally, we document the service, provide aftercare guidance (including cure time), coordinate with insurance when comprehensive coverage applies, and back the work with a lifetime workmanship warranty.
Services
Service Areas
OEM-Quality Sunroof Glass Replacement for Ford Expedition El: DOT Markings and FMVSS 205 Explained
What FMVSS 205 Means for Ford Expedition El Sunroof and Panoramic Roof Glass
FMVSS 205 (49 CFR 571.205) is the federal baseline for automotive safety glazing, covering sunroof and panoramic roof glass on your Ford Expedition El. The rule incorporates ANSI/SAE Z26.1, so compliant glass must meet defined test categories and display specific etched certification marks. This framework exists to ensure roof glass maintains usable optical clarity, tolerates temperature swings and moisture, and breaks in a known, safety-oriented manner. For Ford Expedition El sunroof glass replacement, OEM-quality starts with matching what the factory installed. The correct panel should match the original build (tempered or laminated), carry the proper AS classification for roof placement, and show valid DOT/AS markings indicating it was produced and labeled under FMVSS 205. When those identifiers line up, you are far more likely to get the right tint tone, thickness, edge finish, and bonding surface details that support proper sealing and sunroof operation. Bang AutoGlass photographs your existing roof-glass stamp, verifies the markings, and sources an FMVSS-compliant OEM-quality match before scheduling mobile service—often next day. Most installs take 30–45 minutes; allow about an hour of cure time where bonding applies. We back our work with a lifetime workmanship warranty and coordinate with all insurers when comprehensive coverage applies.
How to Read the Sunroof Glass Stamp: DOT Symbol, Manufacturer Code, and Required Marks
The stamp etched into your Ford Expedition El sunroof or panoramic roof glass functions as its compliance label. Knowing what it means helps you verify you are comparing like-for-like parts and strengthens documentation for a claim. Start with the “DOT” marking. Under FMVSS 205, prime glazing manufacturers add DOT plus a manufacturer number assigned by NHTSA, linking the panel to the company that certified it as U.S. motor-vehicle safety glazing. Then confirm the AS classification (AS1, AS2, AS3, etc.) from ANSI/SAE Z26.1. These codes align with tested performance requirements and allowable installation locations. Windshields are often AS1, while Ford Expedition El roof panels are commonly AS2 or AS3 depending on factory tint and design. Many stamps also call out construction—“TEMPERED” or “LAMINATED”—and may include a logo, an “M” model code, production date/batch symbols, and indicators for coatings or privacy tint. You might also see international approvals like an “E” mark with “43R” (UNECE R43). That can be legitimate, but the replacement should still match your original DOT/AS details, tint cues, and construction. Bang AutoGlass photographs the stamp, verifies the markings, and sources an OEM-quality match through mobile service.
AS Ratings and Safety Glazing Types: What the Markings Indicate for Roof Glass
On your Ford Expedition El, the “AS” code etched on the sunroof or panoramic roof glass is the safety-glazing classification from ANSI/SAE Z26.1, which FMVSS 205 incorporates. AS codes indicate the performance category the glass was tested to and where it is intended to be installed. AS1 is typically used for windshields because it aligns with stricter optical and light-transmission requirements, while roof glass is commonly marked AS2 or AS3 based on vehicle design and factory tint. The stamp also identifies construction. Tempered safety glass is heat-treated and usually fractures into many small pieces to reduce sharp shards. Laminated safety glass uses an interlayer that helps retain fragments; depending on the build, it can improve retention, reduce noise, and support UV or solar-control features. Because roof systems vary by trim and model year, OEM-quality Ford Expedition El roof-glass replacement means matching the original construction and markings, not guessing. Why it matters: AS rating, tint category, and glass type affect glare, heat rejection, break behavior, and overall compliance. Bang AutoGlass verifies the AS code and whether the panel is tempered or laminated, then sources an OEM-quality, FMVSS 205-compliant match for your Ford Expedition El sunroof or panoramic roof replacement.
OEM-Quality Match for Ford Expedition El: Tint, Coatings, Hardware, and Sensor Compatibility
An OEM-quality match for Ford Expedition El roof glass means the panel looks and performs like the factory part. Sunroof and panoramic roof panels are engineered to a specific curvature, thickness, and tint tone, and many include UV filtration and solar-control coatings that reduce infrared heat while maintaining clarity. If replacement glass is not built to the same spec, the difference can be obvious: a slightly different color in sunlight, a two-tone roof, or changed heat rejection on bright days. Perimeter details are functional, not cosmetic. The ceramic frit band and dot matrix create a uniform bonding surface, protect urethane from UV exposure, and conceal the bond line and trim for an OEM finish. Roof glass can also include encapsulation, polished edges, brackets, and locating features that set panel height and determine how seals compress and how wind noise is managed at speed. On many Ford Expedition El configurations, those interfaces must match so the tilt/slide mechanism and sunshade move smoothly. Bang AutoGlass verifies the stamp, DOT markings, and key fitment features, then sources a verified OEM-quality match for your Ford Expedition El. Our fully mobile service can often perform roof glass replacement as soon as next day, backed by a lifetime workmanship warranty.
Installation Standards That Protect the Result: Bond Prep, Adhesive Choice, and AGRSS Best Practices
The difference between installed and installed correctly is process control. For Ford Expedition El sunroof and panoramic roof glass, installation standards prevent leaks, wind noise, rattles, and premature seal failure. A high-quality panel still depends on correct removal technique, meticulous surface preparation, and the adhesive or mechanical retention method specified for the roof system. We protect the cabin, remove the damaged panel safely, and inspect the aperture, seals, and mounting points so the replacement can sit at the proper OEM height. Surface prep is mandatory. The bond area must be clean, dry, and free of oils, glass dust, and residue that reduce adhesion. Where urethane bonding is used, old urethane is managed to a uniform, stable base as appropriate, and any bare metal or corrosion is treated so the adhesive has a reliable substrate. When required, we apply the correct activator and primer sequence to ensure compatible chemical bonding and UV protection at the bond line. Adhesive handling matters too; automotive urethanes cure predictably only when used per spec. AGRSS provides a benchmark for safe removal, proper prep, adhesive handling, and verification. Bang AutoGlass follows these best practices on every mobile roof-glass job and provides aftercare guidance, including recommended cure time before drive-away, often at least one hour when bonding applies.
Post-Install Verification: Fit, Leak/Wind Noise Checks, and Documentation for Ford Expedition El
A professional Ford Expedition El sunroof glass replacement is not complete until post-install verification is done. These checks prevent common complaints: sunroof leaks, wind noise, rattles, and "won't close" issues. First, we confirm fit and finish. The panel should sit flush to the roofline with even gaps, proper seal compression, and clean alignment with trim, moldings, and the sunshade track. Mounts, locating tabs, and fasteners are rechecked so the glass is not sitting high, low, or twisted. Next, we test operation. We cycle the sunroof and sunshade through vent, open, close, and any express functions to confirm smooth travel and correct stop points. Many roof systems require initialization or a teach procedure after service so the motor learns limits and anti-pinch behavior; completing it helps prevent false reversals or incomplete closing. Then we validate sealing and water management. Because sunroofs route water through a tray and drain tubes, we perform a controlled water test to confirm proper routing and drainage rather than pooling. When appropriate, we add a brief road-speed wind-noise check. Finally, we document the service, provide aftercare guidance (including cure time), coordinate with insurance when comprehensive coverage applies, and back the work with a lifetime workmanship warranty.
Enjoy More Relevant Blogs
Tempered vs Laminated Door Glass on Dodge Ram 2500 Regular Cab: What’s Used and Why It Matters
Tempered vs laminated door glass on Dodge Ram 2500 Regular Cab: what your vehicle uses, how it breaks, and what it means for replacement safety, cost, and cleanup.
How to Schedule ADAS Calibration for Ford F250 Super Duty Crew Cab After Windshield Replacement
Schedule ADAS calibration for Ford F250 Super Duty Crew Cab after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
After a Break-In: Dodge Challenger Quarter Glass Replacement Plan to Restore Security and Visibility
After a break-in on Dodge Challenger, restore security with a quarter glass replacement plan: cleanup, temporary protection, scheduling, and post-install checks.
Will Insurance Cover Door Glass Replacement for a Ford Focus RS? Claims Steps, Deductibles, and What to Document
Will insurance cover Ford Focus RS door glass replacement? Learn claim steps, deductibles, photos to document, and how to schedule fast repairs today.
ADAS After Windshield Replacement on Gmc Terrain: Calibration Basics and Safety Checks
ADAS after Gmc Terrain windshield replacement: calibration basics, common safety checks, and how to confirm cameras and sensors are working correctly.
How to Schedule Mobile Rear Glass Replacement for Gmc Rally Wagon 2500
Schedule mobile rear glass replacement for your Gmc Rally Wagon 2500 in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Stop Leaks and Wind Noise: What Proper Dodge Durango Quarter Glass Replacement Should Prevent
Stop leaks and wind noise with proper Dodge Durango quarter glass replacement. Learn what correct fit, sealing, and trim should prevent after install.
Tempered Safety Rear Glass Replacement for Gmc Canyon Crew Cab: Understanding DOT Markings and FMVSS 205
Need Gmc Canyon Crew Cab rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Post-Install Checks for Gmc Sierra (Classic) 1500 Extended Cab: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Gmc Sierra (Classic) 1500 Extended Cab: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Fast Scheduling Guide: Gmc Sierra 3500 Hd Extended Cab Windshield Replacement From Booking to Install
Book Gmc Sierra 3500 Hd Extended Cab windshield replacement fast. See scheduling steps, what to prep, install timing, and when you can safely drive away. Get a quote today.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm