Services
Service Areas
ADAS Warning Lights on Ford Fusion: What the Icons and Messages Commonly Indicate
ADAS icons or “driver assist” messages on your Ford Fusion usually mean the vehicle has reduced or disabled a safety feature because sensor inputs did not pass its self-check. The dash symbol points to the feature: lane-line graphics for Lane Keep Assist/Lane Departure Warning, a crash icon for Forward Collision Warning or Automatic Emergency Braking, and a cruise/speedometer symbol for Adaptive Cruise Control. Text such as “Service Driver Assist,” “Camera Obscured,” “Front Sensor Blocked,” or “ACC Unavailable” is common when the camera or radar can’t see clearly. Before assuming a repair is required, do quick visibility checks. Clean the camera viewing zone near the rearview mirror inside and out; haze, fogging, frost, salt film, and wiper streaks can hide lane markings. Verify washer function and blades. Then inspect the front fascia where the radar looks through a cover or emblem and remove dirt, bugs, ice, or snow. In severe weather (rain, fog, blowing snow, glare), brief dropouts can be normal. If the warning started right after windshield damage, a windshield replacement, or a minor front-end tap, calibration may be needed. Bang AutoGlass offers mobile next-day service, 30–45 minute installs, at least 1 hour safe drive-away time, and a lifetime workmanship warranty.
When Calibration Is the Fix for Ford Fusion: Post-Windshield Replacement and Sensor Alignment Triggers
Calibration on a Ford Fusion is an aiming and reference reset. The forward camera and radar must agree on where “straight ahead” is so the software can judge lanes, closing distance, and object position. That’s why calibration is most commonly needed after a windshield replacement, camera bracket service, or front-end work that required removing and reinstalling the radar. Even small shifts in bracket angle, fastener torque, or windshield specification can trigger “ACC Unavailable,” “Driver Assist Limited,” or “Calibration Required” and keep features offline. A second group of triggers involves geometry changes that move the baseline the modules expect. Alignment adjustments, suspension or ride-height changes, steering repairs, and non-OEM tire sizing can invalidate prior calibration data. A clean workflow reduces comebacks: document DTCs with a pre-scan, verify the correct windshield for the Ford Fusion, inspect the camera mount and radar cover, confirm stable battery voltage and tire pressures, run the required static targets and/or dynamic road learning, then complete a post-scan to confirm everything is clear. Bang AutoGlass can handle the glass portion with mobile next-day service and a lifetime workmanship warranty.
When It’s Not Calibration on Ford Fusion: Obstructions, Damage, Voltage, Wiring, and Module Faults
Not every ADAS warning on a Ford Fusion is solved with calibration. Many alerts are input-quality issues that make the system temporarily shut down. Frost, condensation, mud, road salt, heavy rain, or snow across the camera area can trigger “Camera Obscured” and pause Lane Keep Assist or Forward Collision features until the glass clears. If lane markings are faded or covered, lane-keeping may also suspend because the camera cannot track the road reliably. Other obstructions are self-inflicted: stickers or toll tags in the camera’s view, a dashcam mount too close to the sensor, aftermarket tint over the camera window, or a damaged radar cover/emblem. Electrical stability matters as well. A weak 12-volt battery, a battery disconnect, or charging issues can set driver-assist and communication faults because ADAS modules are sensitive to voltage dips during self-checks. If warnings persist, treat it as diagnostics, not guessing. A scan for DTCs helps separate blocked sensors from fuse, wiring, connector, corrosion, module, or software faults. If the issue started after windshield damage or replacement on your Ford Fusion, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Ford Fusion: Reading DTCs, Root-Cause Checks, and OEM Procedures
On a modern Ford Fusion, clearing ADAS warning lights starts with scan data, not parts swapping. The dash icon only tells you a system is limited; it does not identify the trigger. Many OEM procedures call for a pre-repair health scan whenever the windshield camera, front radar, ABS/steering inputs, or related wiring has been disturbed—common after windshield replacement, collision or bumper work, alignments, suspension changes, or low-voltage events. Run a pre-scan with a tool that can access ADAS, ABS, steering, and body modules. Save all DTCs (current, pending, history) and freeze-frame information before clearing anything, and use the results to confirm which driver-assist features your Ford Fusion actually has. Then follow OEM service information: confirm stable battery/charging voltage, inspect fuses and grounds, and check connectors and harness routing at the camera and radar for corrosion, pin-fit issues, or strain. Verify the correct windshield specification, an intact and properly bonded camera bracket, and clean, unobstructed sensor viewing zones. Ensure prerequisites are within spec—tire size/pressure, ride height, and alignment—before attempting calibration. After corrections and any required calibration/initialization, complete a post-scan to confirm codes are resolved and do not return. Bang AutoGlass can handle mobile next-day glass service and help coordinate the OEM-required next step.
Static vs Dynamic ADAS Calibration for Ford Fusion: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both return your Ford Fusion to OEM aiming specs, but they work differently and have strict prerequisites. Static calibration is done with the vehicle stationary in a controlled bay using OEM targets, measurements, and a scan tool to start the routine. Success typically requires a level floor, precise target distance/height, consistent lighting, correct tire pressures and tire size, normal ride height, and no active DTCs that would block the procedure. Dynamic calibration is completed on the road. The technician puts the system in learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, time or distance requirements, clear lane markings, and good visibility. Weather, traffic, construction zones, glare, or inconsistent lane paint can prevent learning and trigger “calibration incomplete” or “system unavailable” messages. Many Ford Fusion platforms require static, dynamic, or a dual process depending on what was disturbed (camera vs radar), and some also require steering angle sensor initialization. Calibration is not a reset: if alignment is out of spec, voltage is unstable, or the camera/radar area is obstructed, the warning may return even after an attempted routine. Bang AutoGlass offers mobile next-day windshield replacement and can help you plan the required OEM calibration.
Proving the Repair Worked on Ford Fusion: Post-Scan, Verification Drive, and Documentation
After ADAS-related work on a Ford Fusion, a warning light turning off is helpful, but proper closeout requires proof. Begin with a post-repair diagnostic scan across all relevant modules to confirm ADAS-related DTCs are cleared and no new communication, camera, or radar faults are present. If calibration or initialization was performed, retain the completion report showing which routines ran (camera, radar, steering angle sensor as applicable) and that each finished successfully. Next, follow OEM guidance for functional validation. When required, complete a verification drive to confirm lane keep assist stays available, adaptive cruise control engages and holds, and forward collision warning operates normally without “system limited” messages. Also check practical items that affect performance: the windshield camera zone is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare in the camera’s view. Finally, keep documentation organized—pre-scan and post-scan results, OEM procedure references, calibration reports, and road-test notes—to support insurance reimbursement and reduce disputes later. Bang AutoGlass makes the glass portion simple with mobile, as-soon-as-next-day service; most installs take 30–45 minutes plus at least 1 hour of safe drive-away time, and workmanship is backed by a lifetime warranty.
Services
Service Areas
ADAS Warning Lights on Ford Fusion: What the Icons and Messages Commonly Indicate
ADAS icons or “driver assist” messages on your Ford Fusion usually mean the vehicle has reduced or disabled a safety feature because sensor inputs did not pass its self-check. The dash symbol points to the feature: lane-line graphics for Lane Keep Assist/Lane Departure Warning, a crash icon for Forward Collision Warning or Automatic Emergency Braking, and a cruise/speedometer symbol for Adaptive Cruise Control. Text such as “Service Driver Assist,” “Camera Obscured,” “Front Sensor Blocked,” or “ACC Unavailable” is common when the camera or radar can’t see clearly. Before assuming a repair is required, do quick visibility checks. Clean the camera viewing zone near the rearview mirror inside and out; haze, fogging, frost, salt film, and wiper streaks can hide lane markings. Verify washer function and blades. Then inspect the front fascia where the radar looks through a cover or emblem and remove dirt, bugs, ice, or snow. In severe weather (rain, fog, blowing snow, glare), brief dropouts can be normal. If the warning started right after windshield damage, a windshield replacement, or a minor front-end tap, calibration may be needed. Bang AutoGlass offers mobile next-day service, 30–45 minute installs, at least 1 hour safe drive-away time, and a lifetime workmanship warranty.
When Calibration Is the Fix for Ford Fusion: Post-Windshield Replacement and Sensor Alignment Triggers
Calibration on a Ford Fusion is an aiming and reference reset. The forward camera and radar must agree on where “straight ahead” is so the software can judge lanes, closing distance, and object position. That’s why calibration is most commonly needed after a windshield replacement, camera bracket service, or front-end work that required removing and reinstalling the radar. Even small shifts in bracket angle, fastener torque, or windshield specification can trigger “ACC Unavailable,” “Driver Assist Limited,” or “Calibration Required” and keep features offline. A second group of triggers involves geometry changes that move the baseline the modules expect. Alignment adjustments, suspension or ride-height changes, steering repairs, and non-OEM tire sizing can invalidate prior calibration data. A clean workflow reduces comebacks: document DTCs with a pre-scan, verify the correct windshield for the Ford Fusion, inspect the camera mount and radar cover, confirm stable battery voltage and tire pressures, run the required static targets and/or dynamic road learning, then complete a post-scan to confirm everything is clear. Bang AutoGlass can handle the glass portion with mobile next-day service and a lifetime workmanship warranty.
When It’s Not Calibration on Ford Fusion: Obstructions, Damage, Voltage, Wiring, and Module Faults
Not every ADAS warning on a Ford Fusion is solved with calibration. Many alerts are input-quality issues that make the system temporarily shut down. Frost, condensation, mud, road salt, heavy rain, or snow across the camera area can trigger “Camera Obscured” and pause Lane Keep Assist or Forward Collision features until the glass clears. If lane markings are faded or covered, lane-keeping may also suspend because the camera cannot track the road reliably. Other obstructions are self-inflicted: stickers or toll tags in the camera’s view, a dashcam mount too close to the sensor, aftermarket tint over the camera window, or a damaged radar cover/emblem. Electrical stability matters as well. A weak 12-volt battery, a battery disconnect, or charging issues can set driver-assist and communication faults because ADAS modules are sensitive to voltage dips during self-checks. If warnings persist, treat it as diagnostics, not guessing. A scan for DTCs helps separate blocked sensors from fuse, wiring, connector, corrosion, module, or software faults. If the issue started after windshield damage or replacement on your Ford Fusion, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Ford Fusion: Reading DTCs, Root-Cause Checks, and OEM Procedures
On a modern Ford Fusion, clearing ADAS warning lights starts with scan data, not parts swapping. The dash icon only tells you a system is limited; it does not identify the trigger. Many OEM procedures call for a pre-repair health scan whenever the windshield camera, front radar, ABS/steering inputs, or related wiring has been disturbed—common after windshield replacement, collision or bumper work, alignments, suspension changes, or low-voltage events. Run a pre-scan with a tool that can access ADAS, ABS, steering, and body modules. Save all DTCs (current, pending, history) and freeze-frame information before clearing anything, and use the results to confirm which driver-assist features your Ford Fusion actually has. Then follow OEM service information: confirm stable battery/charging voltage, inspect fuses and grounds, and check connectors and harness routing at the camera and radar for corrosion, pin-fit issues, or strain. Verify the correct windshield specification, an intact and properly bonded camera bracket, and clean, unobstructed sensor viewing zones. Ensure prerequisites are within spec—tire size/pressure, ride height, and alignment—before attempting calibration. After corrections and any required calibration/initialization, complete a post-scan to confirm codes are resolved and do not return. Bang AutoGlass can handle mobile next-day glass service and help coordinate the OEM-required next step.
Static vs Dynamic ADAS Calibration for Ford Fusion: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both return your Ford Fusion to OEM aiming specs, but they work differently and have strict prerequisites. Static calibration is done with the vehicle stationary in a controlled bay using OEM targets, measurements, and a scan tool to start the routine. Success typically requires a level floor, precise target distance/height, consistent lighting, correct tire pressures and tire size, normal ride height, and no active DTCs that would block the procedure. Dynamic calibration is completed on the road. The technician puts the system in learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, time or distance requirements, clear lane markings, and good visibility. Weather, traffic, construction zones, glare, or inconsistent lane paint can prevent learning and trigger “calibration incomplete” or “system unavailable” messages. Many Ford Fusion platforms require static, dynamic, or a dual process depending on what was disturbed (camera vs radar), and some also require steering angle sensor initialization. Calibration is not a reset: if alignment is out of spec, voltage is unstable, or the camera/radar area is obstructed, the warning may return even after an attempted routine. Bang AutoGlass offers mobile next-day windshield replacement and can help you plan the required OEM calibration.
Proving the Repair Worked on Ford Fusion: Post-Scan, Verification Drive, and Documentation
After ADAS-related work on a Ford Fusion, a warning light turning off is helpful, but proper closeout requires proof. Begin with a post-repair diagnostic scan across all relevant modules to confirm ADAS-related DTCs are cleared and no new communication, camera, or radar faults are present. If calibration or initialization was performed, retain the completion report showing which routines ran (camera, radar, steering angle sensor as applicable) and that each finished successfully. Next, follow OEM guidance for functional validation. When required, complete a verification drive to confirm lane keep assist stays available, adaptive cruise control engages and holds, and forward collision warning operates normally without “system limited” messages. Also check practical items that affect performance: the windshield camera zone is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare in the camera’s view. Finally, keep documentation organized—pre-scan and post-scan results, OEM procedure references, calibration reports, and road-test notes—to support insurance reimbursement and reduce disputes later. Bang AutoGlass makes the glass portion simple with mobile, as-soon-as-next-day service; most installs take 30–45 minutes plus at least 1 hour of safe drive-away time, and workmanship is backed by a lifetime warranty.
Services
Service Areas
ADAS Warning Lights on Ford Fusion: What the Icons and Messages Commonly Indicate
ADAS icons or “driver assist” messages on your Ford Fusion usually mean the vehicle has reduced or disabled a safety feature because sensor inputs did not pass its self-check. The dash symbol points to the feature: lane-line graphics for Lane Keep Assist/Lane Departure Warning, a crash icon for Forward Collision Warning or Automatic Emergency Braking, and a cruise/speedometer symbol for Adaptive Cruise Control. Text such as “Service Driver Assist,” “Camera Obscured,” “Front Sensor Blocked,” or “ACC Unavailable” is common when the camera or radar can’t see clearly. Before assuming a repair is required, do quick visibility checks. Clean the camera viewing zone near the rearview mirror inside and out; haze, fogging, frost, salt film, and wiper streaks can hide lane markings. Verify washer function and blades. Then inspect the front fascia where the radar looks through a cover or emblem and remove dirt, bugs, ice, or snow. In severe weather (rain, fog, blowing snow, glare), brief dropouts can be normal. If the warning started right after windshield damage, a windshield replacement, or a minor front-end tap, calibration may be needed. Bang AutoGlass offers mobile next-day service, 30–45 minute installs, at least 1 hour safe drive-away time, and a lifetime workmanship warranty.
When Calibration Is the Fix for Ford Fusion: Post-Windshield Replacement and Sensor Alignment Triggers
Calibration on a Ford Fusion is an aiming and reference reset. The forward camera and radar must agree on where “straight ahead” is so the software can judge lanes, closing distance, and object position. That’s why calibration is most commonly needed after a windshield replacement, camera bracket service, or front-end work that required removing and reinstalling the radar. Even small shifts in bracket angle, fastener torque, or windshield specification can trigger “ACC Unavailable,” “Driver Assist Limited,” or “Calibration Required” and keep features offline. A second group of triggers involves geometry changes that move the baseline the modules expect. Alignment adjustments, suspension or ride-height changes, steering repairs, and non-OEM tire sizing can invalidate prior calibration data. A clean workflow reduces comebacks: document DTCs with a pre-scan, verify the correct windshield for the Ford Fusion, inspect the camera mount and radar cover, confirm stable battery voltage and tire pressures, run the required static targets and/or dynamic road learning, then complete a post-scan to confirm everything is clear. Bang AutoGlass can handle the glass portion with mobile next-day service and a lifetime workmanship warranty.
When It’s Not Calibration on Ford Fusion: Obstructions, Damage, Voltage, Wiring, and Module Faults
Not every ADAS warning on a Ford Fusion is solved with calibration. Many alerts are input-quality issues that make the system temporarily shut down. Frost, condensation, mud, road salt, heavy rain, or snow across the camera area can trigger “Camera Obscured” and pause Lane Keep Assist or Forward Collision features until the glass clears. If lane markings are faded or covered, lane-keeping may also suspend because the camera cannot track the road reliably. Other obstructions are self-inflicted: stickers or toll tags in the camera’s view, a dashcam mount too close to the sensor, aftermarket tint over the camera window, or a damaged radar cover/emblem. Electrical stability matters as well. A weak 12-volt battery, a battery disconnect, or charging issues can set driver-assist and communication faults because ADAS modules are sensitive to voltage dips during self-checks. If warnings persist, treat it as diagnostics, not guessing. A scan for DTCs helps separate blocked sensors from fuse, wiring, connector, corrosion, module, or software faults. If the issue started after windshield damage or replacement on your Ford Fusion, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Ford Fusion: Reading DTCs, Root-Cause Checks, and OEM Procedures
On a modern Ford Fusion, clearing ADAS warning lights starts with scan data, not parts swapping. The dash icon only tells you a system is limited; it does not identify the trigger. Many OEM procedures call for a pre-repair health scan whenever the windshield camera, front radar, ABS/steering inputs, or related wiring has been disturbed—common after windshield replacement, collision or bumper work, alignments, suspension changes, or low-voltage events. Run a pre-scan with a tool that can access ADAS, ABS, steering, and body modules. Save all DTCs (current, pending, history) and freeze-frame information before clearing anything, and use the results to confirm which driver-assist features your Ford Fusion actually has. Then follow OEM service information: confirm stable battery/charging voltage, inspect fuses and grounds, and check connectors and harness routing at the camera and radar for corrosion, pin-fit issues, or strain. Verify the correct windshield specification, an intact and properly bonded camera bracket, and clean, unobstructed sensor viewing zones. Ensure prerequisites are within spec—tire size/pressure, ride height, and alignment—before attempting calibration. After corrections and any required calibration/initialization, complete a post-scan to confirm codes are resolved and do not return. Bang AutoGlass can handle mobile next-day glass service and help coordinate the OEM-required next step.
Static vs Dynamic ADAS Calibration for Ford Fusion: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both return your Ford Fusion to OEM aiming specs, but they work differently and have strict prerequisites. Static calibration is done with the vehicle stationary in a controlled bay using OEM targets, measurements, and a scan tool to start the routine. Success typically requires a level floor, precise target distance/height, consistent lighting, correct tire pressures and tire size, normal ride height, and no active DTCs that would block the procedure. Dynamic calibration is completed on the road. The technician puts the system in learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, time or distance requirements, clear lane markings, and good visibility. Weather, traffic, construction zones, glare, or inconsistent lane paint can prevent learning and trigger “calibration incomplete” or “system unavailable” messages. Many Ford Fusion platforms require static, dynamic, or a dual process depending on what was disturbed (camera vs radar), and some also require steering angle sensor initialization. Calibration is not a reset: if alignment is out of spec, voltage is unstable, or the camera/radar area is obstructed, the warning may return even after an attempted routine. Bang AutoGlass offers mobile next-day windshield replacement and can help you plan the required OEM calibration.
Proving the Repair Worked on Ford Fusion: Post-Scan, Verification Drive, and Documentation
After ADAS-related work on a Ford Fusion, a warning light turning off is helpful, but proper closeout requires proof. Begin with a post-repair diagnostic scan across all relevant modules to confirm ADAS-related DTCs are cleared and no new communication, camera, or radar faults are present. If calibration or initialization was performed, retain the completion report showing which routines ran (camera, radar, steering angle sensor as applicable) and that each finished successfully. Next, follow OEM guidance for functional validation. When required, complete a verification drive to confirm lane keep assist stays available, adaptive cruise control engages and holds, and forward collision warning operates normally without “system limited” messages. Also check practical items that affect performance: the windshield camera zone is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare in the camera’s view. Finally, keep documentation organized—pre-scan and post-scan results, OEM procedure references, calibration reports, and road-test notes—to support insurance reimbursement and reduce disputes later. Bang AutoGlass makes the glass portion simple with mobile, as-soon-as-next-day service; most installs take 30–45 minutes plus at least 1 hour of safe drive-away time, and workmanship is backed by a lifetime warranty.
Enjoy More Relevant Blogs
Tempered vs Laminated Door Glass on Dodge Ram 2500 Regular Cab: What’s Used and Why It Matters
Tempered vs laminated door glass on Dodge Ram 2500 Regular Cab: what your vehicle uses, how it breaks, and what it means for replacement safety, cost, and cleanup.
How to Schedule ADAS Calibration for Ford F250 Super Duty Crew Cab After Windshield Replacement
Schedule ADAS calibration for Ford F250 Super Duty Crew Cab after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
After a Break-In: Dodge Challenger Quarter Glass Replacement Plan to Restore Security and Visibility
After a break-in on Dodge Challenger, restore security with a quarter glass replacement plan: cleanup, temporary protection, scheduling, and post-install checks.
Will Insurance Cover Door Glass Replacement for a Ford Focus RS? Claims Steps, Deductibles, and What to Document
Will insurance cover Ford Focus RS door glass replacement? Learn claim steps, deductibles, photos to document, and how to schedule fast repairs today.
ADAS After Windshield Replacement on Gmc Terrain: Calibration Basics and Safety Checks
ADAS after Gmc Terrain windshield replacement: calibration basics, common safety checks, and how to confirm cameras and sensors are working correctly.
How to Schedule Mobile Rear Glass Replacement for Gmc Rally Wagon 2500
Schedule mobile rear glass replacement for your Gmc Rally Wagon 2500 in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Stop Leaks and Wind Noise: What Proper Dodge Durango Quarter Glass Replacement Should Prevent
Stop leaks and wind noise with proper Dodge Durango quarter glass replacement. Learn what correct fit, sealing, and trim should prevent after install.
Tempered Safety Rear Glass Replacement for Gmc Canyon Crew Cab: Understanding DOT Markings and FMVSS 205
Need Gmc Canyon Crew Cab rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Post-Install Checks for Gmc Sierra (Classic) 1500 Extended Cab: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Gmc Sierra (Classic) 1500 Extended Cab: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Fast Scheduling Guide: Gmc Sierra 3500 Hd Extended Cab Windshield Replacement From Booking to Install
Book Gmc Sierra 3500 Hd Extended Cab windshield replacement fast. See scheduling steps, what to prep, install timing, and when you can safely drive away. Get a quote today.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm