Services
Service Areas
Do You Need ADAS Calibration for Mazda CX-4 After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
A Mazda CX-4 can drive straight after an alignment and still have ADAS that’s slightly out of sync if the reference angles changed. Lane-keeping assist and lane departure warning use lane lines from the forward camera, but the software also depends on the vehicle’s calibrated centerline and an accurate steering angle sensor (SAS) baseline. ACC and AEB likewise assume the camera/radar are aimed relative to the true direction of travel. When a technician adjusts toe, camber, caster, or corrects thrust angle, the Mazda CX-4 may follow a subtly different path than before. If the SAS zero point and sensor aiming are not updated, the system can misread what “straight ahead” is. That’s why OEM workflows often pair alignment with a scan-tool routine: pre-scan for stored codes, SAS reset or relearn, then calibration verification for the front camera and/or radar using static targets, a dynamic road drive, or both. A practical red flag is an alignment invoice with no post-scan results or calibration documentation. In real driving, miscalibration can feel like drifting lane centering, ACC that changes following behavior unexpectedly, or warnings that trigger too early or too late. Choose providers that confirm alignment specs first and then record the calibration outcome.
Mazda CX-4 ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Mazda CX-4—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Mazda CX-4 set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Mazda CX-4 After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
It doesn’t take a major crash to push ADAS out of spec on a Mazda CX-4. A light rear-end, slow-speed bumper hit, or curb impact can transfer force into the bumper structure, sensor brackets, or windshield/camera area. Because radar and camera assemblies are aimed within very small tolerances, a tiny shift in a bracket, bumper reinforcement, or camera mount can change what the system “thinks” is straight ahead. The symptoms may be subtle: ACC that feels inconsistent, forward-collision warnings that seem early or late, lane-keeping that drifts, or intermittent false alerts. Often there is no warning light, so the reliable approach is to scan for stored codes and follow OEM calibration requirements. Post-impact best practice is a diagnostic pre-scan, any required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status. Save the calibration report with your repair paperwork, since insurers and future shops often ask for proof. If the incident also damaged your windshield—especially on Mazda CX-4 trims with windshield-mounted cameras—Bang AutoGlass can provide mobile replacement when scheduling allows. Most installs take 30–45 minutes; plan at least one hour of safe drive time for adhesive cure. We can also help you organize scan results and direct you to an appropriate calibration resource.
Signs Your Mazda CX-4 ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
On a Mazda CX-4, ADAS calibration problems do not always look like a dramatic failure. A dashboard message for the camera, radar, lane assist, or ACC is a clear indicator, but many drivers notice subtle changes first: lane-keeping that favors one side, lane departure warnings that feel overly sensitive, or lane-centering that wanders on roads with clear markings. Adaptive cruise control (ACC) may brake too aggressively, vary the following gap, or react late to vehicles ahead. You might also get random forward-collision warnings or blind-spot alerts at the wrong times. These symptoms can happen when sensor aim is slightly off, a radar bracket shifted, a windshield-mounted camera moved, or the steering angle sensor baseline no longer matches straight-ahead. The best clue is timing. If the behavior began after windshield replacement, alignment, suspension/steering repair, bumper work, or a minor impact, treat calibration verification as a safety step. An OEM-aligned approach is: scan for codes, confirm prerequisites (tires, ride height, alignment), complete static and/or dynamic calibration, then document results. If cracked glass is involved, Bang AutoGlass provides next-day mobile windshield replacement when scheduling allows. Most replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and are backed by a lifetime workmanship warranty.
How Shops Confirm Mazda CX-4 ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
To verify your Mazda CX-4 ADAS is truly in-spec, a quality shop relies on process and documentation, not a quick drive. Step one is a pre-repair diagnostic scan to capture diagnostic trouble codes (DTCs), module communication status, and any stored ADAS history faults. Next, they confirm the mechanical items that make calibration valid: correct tire size and pressure, proper ride height, no looseness in steering or suspension, and a four-wheel alignment within spec (including thrust angle). Because ADAS targets vehicle geometry, even small alignment or ride-height errors can compromise camera calibration and radar calibration. With prerequisites met, the shop checks the exact ADAS configuration on your Mazda CX-4 and selects the required OEM procedures for the repair event. Calibration may be static (targets placed at measured distances and heights on a level floor with controlled lighting) and/or dynamic (a scan-tool initiated road routine completed under defined speed, lane-marking, and weather conditions). After the routine, a post-scan confirms codes are cleared and systems report normal operation. Ask for proof: pre-scan/post-scan printouts, alignment measurements when applicable, and the ADAS calibration report (certificate) showing successful completion and final status.
Insurance and Warranty Questions for Mazda CX-4 ADAS Calibration: What’s Typically Covered and What to Document
With Mazda CX-4 ADAS calibration, reimbursement usually depends on the cause. Collision-related calibrations (bumper repair, sensor bracket replacement, suspension impact) are commonly billed under collision coverage. Calibrations required after windshield replacement on a Mazda CX-4 with a windshield-mounted camera are often handled under comprehensive coverage, especially when the camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Deductibles and carrier rules vary, so ask whether scanning and camera/radar calibration are reimbursable for your claim. Make the decision easy for the adjuster by keeping strong documentation: a repair order stating the trigger event, photos of the affected area, alignment printouts if alignment or ride height was part of the job, and both pre-scan and post-scan results. The key document is the ADAS calibration report showing the procedure performed and the final pass status. It also helps when invoices separate glass work, diagnostic scanning, and calibration labor. Bang AutoGlass supports the glass portion with mobile service (often as soon as next day when scheduling allows) and works with all insurers when comprehensive coverage applies. Windshield replacement typically takes 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and includes a lifetime workmanship warranty.
Services
Service Areas
Do You Need ADAS Calibration for Mazda CX-4 After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
A Mazda CX-4 can drive straight after an alignment and still have ADAS that’s slightly out of sync if the reference angles changed. Lane-keeping assist and lane departure warning use lane lines from the forward camera, but the software also depends on the vehicle’s calibrated centerline and an accurate steering angle sensor (SAS) baseline. ACC and AEB likewise assume the camera/radar are aimed relative to the true direction of travel. When a technician adjusts toe, camber, caster, or corrects thrust angle, the Mazda CX-4 may follow a subtly different path than before. If the SAS zero point and sensor aiming are not updated, the system can misread what “straight ahead” is. That’s why OEM workflows often pair alignment with a scan-tool routine: pre-scan for stored codes, SAS reset or relearn, then calibration verification for the front camera and/or radar using static targets, a dynamic road drive, or both. A practical red flag is an alignment invoice with no post-scan results or calibration documentation. In real driving, miscalibration can feel like drifting lane centering, ACC that changes following behavior unexpectedly, or warnings that trigger too early or too late. Choose providers that confirm alignment specs first and then record the calibration outcome.
Mazda CX-4 ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Mazda CX-4—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Mazda CX-4 set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Mazda CX-4 After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
It doesn’t take a major crash to push ADAS out of spec on a Mazda CX-4. A light rear-end, slow-speed bumper hit, or curb impact can transfer force into the bumper structure, sensor brackets, or windshield/camera area. Because radar and camera assemblies are aimed within very small tolerances, a tiny shift in a bracket, bumper reinforcement, or camera mount can change what the system “thinks” is straight ahead. The symptoms may be subtle: ACC that feels inconsistent, forward-collision warnings that seem early or late, lane-keeping that drifts, or intermittent false alerts. Often there is no warning light, so the reliable approach is to scan for stored codes and follow OEM calibration requirements. Post-impact best practice is a diagnostic pre-scan, any required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status. Save the calibration report with your repair paperwork, since insurers and future shops often ask for proof. If the incident also damaged your windshield—especially on Mazda CX-4 trims with windshield-mounted cameras—Bang AutoGlass can provide mobile replacement when scheduling allows. Most installs take 30–45 minutes; plan at least one hour of safe drive time for adhesive cure. We can also help you organize scan results and direct you to an appropriate calibration resource.
Signs Your Mazda CX-4 ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
On a Mazda CX-4, ADAS calibration problems do not always look like a dramatic failure. A dashboard message for the camera, radar, lane assist, or ACC is a clear indicator, but many drivers notice subtle changes first: lane-keeping that favors one side, lane departure warnings that feel overly sensitive, or lane-centering that wanders on roads with clear markings. Adaptive cruise control (ACC) may brake too aggressively, vary the following gap, or react late to vehicles ahead. You might also get random forward-collision warnings or blind-spot alerts at the wrong times. These symptoms can happen when sensor aim is slightly off, a radar bracket shifted, a windshield-mounted camera moved, or the steering angle sensor baseline no longer matches straight-ahead. The best clue is timing. If the behavior began after windshield replacement, alignment, suspension/steering repair, bumper work, or a minor impact, treat calibration verification as a safety step. An OEM-aligned approach is: scan for codes, confirm prerequisites (tires, ride height, alignment), complete static and/or dynamic calibration, then document results. If cracked glass is involved, Bang AutoGlass provides next-day mobile windshield replacement when scheduling allows. Most replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and are backed by a lifetime workmanship warranty.
How Shops Confirm Mazda CX-4 ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
To verify your Mazda CX-4 ADAS is truly in-spec, a quality shop relies on process and documentation, not a quick drive. Step one is a pre-repair diagnostic scan to capture diagnostic trouble codes (DTCs), module communication status, and any stored ADAS history faults. Next, they confirm the mechanical items that make calibration valid: correct tire size and pressure, proper ride height, no looseness in steering or suspension, and a four-wheel alignment within spec (including thrust angle). Because ADAS targets vehicle geometry, even small alignment or ride-height errors can compromise camera calibration and radar calibration. With prerequisites met, the shop checks the exact ADAS configuration on your Mazda CX-4 and selects the required OEM procedures for the repair event. Calibration may be static (targets placed at measured distances and heights on a level floor with controlled lighting) and/or dynamic (a scan-tool initiated road routine completed under defined speed, lane-marking, and weather conditions). After the routine, a post-scan confirms codes are cleared and systems report normal operation. Ask for proof: pre-scan/post-scan printouts, alignment measurements when applicable, and the ADAS calibration report (certificate) showing successful completion and final status.
Insurance and Warranty Questions for Mazda CX-4 ADAS Calibration: What’s Typically Covered and What to Document
With Mazda CX-4 ADAS calibration, reimbursement usually depends on the cause. Collision-related calibrations (bumper repair, sensor bracket replacement, suspension impact) are commonly billed under collision coverage. Calibrations required after windshield replacement on a Mazda CX-4 with a windshield-mounted camera are often handled under comprehensive coverage, especially when the camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Deductibles and carrier rules vary, so ask whether scanning and camera/radar calibration are reimbursable for your claim. Make the decision easy for the adjuster by keeping strong documentation: a repair order stating the trigger event, photos of the affected area, alignment printouts if alignment or ride height was part of the job, and both pre-scan and post-scan results. The key document is the ADAS calibration report showing the procedure performed and the final pass status. It also helps when invoices separate glass work, diagnostic scanning, and calibration labor. Bang AutoGlass supports the glass portion with mobile service (often as soon as next day when scheduling allows) and works with all insurers when comprehensive coverage applies. Windshield replacement typically takes 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and includes a lifetime workmanship warranty.
Services
Service Areas
Do You Need ADAS Calibration for Mazda CX-4 After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
A Mazda CX-4 can drive straight after an alignment and still have ADAS that’s slightly out of sync if the reference angles changed. Lane-keeping assist and lane departure warning use lane lines from the forward camera, but the software also depends on the vehicle’s calibrated centerline and an accurate steering angle sensor (SAS) baseline. ACC and AEB likewise assume the camera/radar are aimed relative to the true direction of travel. When a technician adjusts toe, camber, caster, or corrects thrust angle, the Mazda CX-4 may follow a subtly different path than before. If the SAS zero point and sensor aiming are not updated, the system can misread what “straight ahead” is. That’s why OEM workflows often pair alignment with a scan-tool routine: pre-scan for stored codes, SAS reset or relearn, then calibration verification for the front camera and/or radar using static targets, a dynamic road drive, or both. A practical red flag is an alignment invoice with no post-scan results or calibration documentation. In real driving, miscalibration can feel like drifting lane centering, ACC that changes following behavior unexpectedly, or warnings that trigger too early or too late. Choose providers that confirm alignment specs first and then record the calibration outcome.
Mazda CX-4 ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Mazda CX-4—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Mazda CX-4 set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Mazda CX-4 After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
It doesn’t take a major crash to push ADAS out of spec on a Mazda CX-4. A light rear-end, slow-speed bumper hit, or curb impact can transfer force into the bumper structure, sensor brackets, or windshield/camera area. Because radar and camera assemblies are aimed within very small tolerances, a tiny shift in a bracket, bumper reinforcement, or camera mount can change what the system “thinks” is straight ahead. The symptoms may be subtle: ACC that feels inconsistent, forward-collision warnings that seem early or late, lane-keeping that drifts, or intermittent false alerts. Often there is no warning light, so the reliable approach is to scan for stored codes and follow OEM calibration requirements. Post-impact best practice is a diagnostic pre-scan, any required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status. Save the calibration report with your repair paperwork, since insurers and future shops often ask for proof. If the incident also damaged your windshield—especially on Mazda CX-4 trims with windshield-mounted cameras—Bang AutoGlass can provide mobile replacement when scheduling allows. Most installs take 30–45 minutes; plan at least one hour of safe drive time for adhesive cure. We can also help you organize scan results and direct you to an appropriate calibration resource.
Signs Your Mazda CX-4 ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
On a Mazda CX-4, ADAS calibration problems do not always look like a dramatic failure. A dashboard message for the camera, radar, lane assist, or ACC is a clear indicator, but many drivers notice subtle changes first: lane-keeping that favors one side, lane departure warnings that feel overly sensitive, or lane-centering that wanders on roads with clear markings. Adaptive cruise control (ACC) may brake too aggressively, vary the following gap, or react late to vehicles ahead. You might also get random forward-collision warnings or blind-spot alerts at the wrong times. These symptoms can happen when sensor aim is slightly off, a radar bracket shifted, a windshield-mounted camera moved, or the steering angle sensor baseline no longer matches straight-ahead. The best clue is timing. If the behavior began after windshield replacement, alignment, suspension/steering repair, bumper work, or a minor impact, treat calibration verification as a safety step. An OEM-aligned approach is: scan for codes, confirm prerequisites (tires, ride height, alignment), complete static and/or dynamic calibration, then document results. If cracked glass is involved, Bang AutoGlass provides next-day mobile windshield replacement when scheduling allows. Most replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and are backed by a lifetime workmanship warranty.
How Shops Confirm Mazda CX-4 ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
To verify your Mazda CX-4 ADAS is truly in-spec, a quality shop relies on process and documentation, not a quick drive. Step one is a pre-repair diagnostic scan to capture diagnostic trouble codes (DTCs), module communication status, and any stored ADAS history faults. Next, they confirm the mechanical items that make calibration valid: correct tire size and pressure, proper ride height, no looseness in steering or suspension, and a four-wheel alignment within spec (including thrust angle). Because ADAS targets vehicle geometry, even small alignment or ride-height errors can compromise camera calibration and radar calibration. With prerequisites met, the shop checks the exact ADAS configuration on your Mazda CX-4 and selects the required OEM procedures for the repair event. Calibration may be static (targets placed at measured distances and heights on a level floor with controlled lighting) and/or dynamic (a scan-tool initiated road routine completed under defined speed, lane-marking, and weather conditions). After the routine, a post-scan confirms codes are cleared and systems report normal operation. Ask for proof: pre-scan/post-scan printouts, alignment measurements when applicable, and the ADAS calibration report (certificate) showing successful completion and final status.
Insurance and Warranty Questions for Mazda CX-4 ADAS Calibration: What’s Typically Covered and What to Document
With Mazda CX-4 ADAS calibration, reimbursement usually depends on the cause. Collision-related calibrations (bumper repair, sensor bracket replacement, suspension impact) are commonly billed under collision coverage. Calibrations required after windshield replacement on a Mazda CX-4 with a windshield-mounted camera are often handled under comprehensive coverage, especially when the camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Deductibles and carrier rules vary, so ask whether scanning and camera/radar calibration are reimbursable for your claim. Make the decision easy for the adjuster by keeping strong documentation: a repair order stating the trigger event, photos of the affected area, alignment printouts if alignment or ride height was part of the job, and both pre-scan and post-scan results. The key document is the ADAS calibration report showing the procedure performed and the final pass status. It also helps when invoices separate glass work, diagnostic scanning, and calibration labor. Bang AutoGlass supports the glass portion with mobile service (often as soon as next day when scheduling allows) and works with all insurers when comprehensive coverage applies. Windshield replacement typically takes 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and includes a lifetime workmanship warranty.
Enjoy More Relevant Blogs
OEM Calibration Requirements for Mazda CX-4: How to Confirm What Must Be Calibrated
OEM calibration requirements for Mazda CX-4: how to confirm what must be calibrated after repairs, what triggers recalibration, and what proof to ask for.
Camera Calibration for Mazda CX-4: Lane Assist and Forward Collision Accuracy Explained
Need camera calibration for your Mazda CX-4? See how calibration affects lane assist and forward collision accuracy after windshield service or repairs.
How to Schedule ADAS Calibration for Mazda CX-4 After Windshield Replacement
Schedule ADAS calibration for Mazda CX-4 after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
Static vs Dynamic ADAS Calibration for Mazda CX-4: What the Difference Means
Static vs dynamic ADAS calibration for Mazda CX-4: key differences, when each is required, how long it takes, and what affects accuracy for safety.
Pre- and Post-Calibration Scans for Mazda CX-4: Proving Systems Are Set Correctly
Pre- and post-calibration scans for Mazda CX-4: see why scans matter, what they verify, and how reports prove ADAS systems are set correctly after service.
ADAS Calibration Checklist for Mazda CX-4: Documentation, Verification, and Final Safety Checks
ADAS calibration checklist for Mazda CX-4: documentation to request, scans to verify, and safety checks that confirm cameras and sensors are set right.
How Much Does ADAS Calibration Cost for Mazda CX-4? What Drives Pricing and What Insurance Typically Covers
How much does ADAS calibration cost for a Mazda CX-4? Learn pricing drivers, camera vs radar needs, labor time, and what insurance typically covers.
Mobile ADAS Calibration for Mazda CX-4: What to Expect On-Site and Why Setup Matters
Mobile ADAS calibration for Mazda CX-4: what to expect on-site, space and lighting needs, and why setup and verification matter after repairs today.
ADAS Warning Lights on Mazda CX-4: When Calibration Is the Fix and When It’s Not
ADAS warning lights on your Mazda CX-4? Learn when calibration fixes lane assist or AEB issues, when it will not, and what to check next. Schedule help.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm