Services
Service Areas
Do You Need ADAS Calibration for Mazda CX-80 After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
On a Mazda CX-80, a wheel alignment affects more than steering feel and tire wear—it can also shift the reference angles your Advanced Driver Assistance Systems (ADAS) use for lane-keeping assist (LKA), lane departure warning (LDW), adaptive cruise control (ACC), and automatic emergency braking (AEB). These systems rely on the vehicle’s direction of travel (thrust angle) and a correct steering angle sensor (SAS) zero point to define “straight ahead.” When toe, camber, or caster is adjusted, the Mazda CX-80 may track on a slightly different line, and OEM procedures often call for a SAS reset and an ADAS calibration check so the forward camera and radar match the updated geometry. Depending on requirements, that may be a static target setup, a scan-tool guided dynamic road routine, or both. After any four-wheel alignment, ask if the shop performed a diagnostic pre-scan/post-scan and documented any required camera calibration, radar calibration, or steering angle reset. Skipping steps can show up as LKA that nudges off-center, ACC that behaves inconsistently, or alerts that seem late or overly sensitive. If you’re searching “Mazda CX-80 ADAS calibration after alignment” or “ADAS calibration near me,” choose a process that verifies alignment specs first and records calibration results.
Mazda CX-80 ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Mazda CX-80—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Mazda CX-80 set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Mazda CX-80 After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
It doesn’t take a major crash to push ADAS out of spec on a Mazda CX-80. A light rear-end, slow-speed bumper hit, or curb impact can transfer force into the bumper structure, sensor brackets, or windshield/camera area. Because radar and camera assemblies are aimed within very small tolerances, a tiny shift in a bracket, bumper reinforcement, or camera mount can change what the system “thinks” is straight ahead. The symptoms may be subtle: ACC that feels inconsistent, forward-collision warnings that seem early or late, lane-keeping that drifts, or intermittent false alerts. Often there is no warning light, so the reliable approach is to scan for stored codes and follow OEM calibration requirements. Post-impact best practice is a diagnostic pre-scan, any required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status. Save the calibration report with your repair paperwork, since insurers and future shops often ask for proof. If the incident also damaged your windshield—especially on Mazda CX-80 trims with windshield-mounted cameras—Bang AutoGlass can provide mobile replacement when scheduling allows. Most installs take 30–45 minutes; plan at least one hour of safe drive time for adhesive cure. We can also help you organize scan results and direct you to an appropriate calibration resource.
Signs Your Mazda CX-80 ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
If your Mazda CX-80 has ADAS, a warning light for the camera, radar, or lane assist is the obvious sign calibration may be needed. Many issues show up earlier as behavior that feels "off." Notice lane-keeping assist pulling you off-center, lane departure alerts firing too often, or lane-centering that wanders instead of holding steady. Adaptive cruise control (ACC) can also change: inconsistent following distance, abrupt braking, or unexpected speed changes may mean the camera or radar view is no longer aligned with the vehicle's centerline. Other clues include false forward-collision warnings or blind-spot monitoring that misses vehicles. If this started right after windshield replacement with a windshield-mounted camera, wheel alignment, suspension/steering work, bumper repair, or a minor hit, assume calibration prerequisites shifted. The fix is a scan for codes and an OEM-procedure static and/or dynamic calibration, documented with a calibration report. For searches like "Mazda CX-80 ADAS calibration near me," choose a shop that can scan, calibrate, and provide paperwork. If damaged glass is involved, Bang AutoGlass offers next-day mobile windshield replacement. Installs usually take 30-45 minutes plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
How Shops Confirm Mazda CX-80 ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
When a shop says your Mazda CX-80 ADAS is "good," ask what evidence supports that claim. The standard is an OEM-style process with paperwork. It typically begins with a pre-scan to find diagnostic trouble codes (DTCs) and module status across camera, radar, braking, and lane-assist systems, including history faults that may not trigger a warning light. Next, the shop confirms calibration prerequisites: correct tire size and pressure, proper ride height, no looseness in steering/suspension components, and alignment within spec (including thrust angle). Those checks matter because camera calibration and radar calibration assume the vehicle's geometry is correct. After prerequisites, procedure selection depends on your Mazda CX-80 trim and options. A windshield replacement, bumper repair, alignment, or suspension work may require target-based static calibration, a scan-tool initiated dynamic road routine, or both, sometimes across multiple systems (front camera, front radar, steering angle sensor reset). Once complete, a post-scan verifies normal status and cleared codes. Request the deliverables: pre-scan and post-scan printouts, alignment measurements if performed, and the ADAS calibration report showing completion and final pass status for insurance and your records.
Insurance and Warranty Questions for Mazda CX-80 ADAS Calibration: What’s Typically Covered and What to Document
With Mazda CX-80 ADAS calibration, reimbursement usually depends on the cause. Collision-related calibrations (bumper repair, sensor bracket replacement, suspension impact) are commonly billed under collision coverage. Calibrations required after windshield replacement on a Mazda CX-80 with a windshield-mounted camera are often handled under comprehensive coverage, especially when the camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Deductibles and carrier rules vary, so ask whether scanning and camera/radar calibration are reimbursable for your claim. Make the decision easy for the adjuster by keeping strong documentation: a repair order stating the trigger event, photos of the affected area, alignment printouts if alignment or ride height was part of the job, and both pre-scan and post-scan results. The key document is the ADAS calibration report showing the procedure performed and the final pass status. It also helps when invoices separate glass work, diagnostic scanning, and calibration labor. Bang AutoGlass supports the glass portion with mobile service (often as soon as next day when scheduling allows) and works with all insurers when comprehensive coverage applies. Windshield replacement typically takes 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and includes a lifetime workmanship warranty.
Services
Service Areas
Do You Need ADAS Calibration for Mazda CX-80 After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
On a Mazda CX-80, a wheel alignment affects more than steering feel and tire wear—it can also shift the reference angles your Advanced Driver Assistance Systems (ADAS) use for lane-keeping assist (LKA), lane departure warning (LDW), adaptive cruise control (ACC), and automatic emergency braking (AEB). These systems rely on the vehicle’s direction of travel (thrust angle) and a correct steering angle sensor (SAS) zero point to define “straight ahead.” When toe, camber, or caster is adjusted, the Mazda CX-80 may track on a slightly different line, and OEM procedures often call for a SAS reset and an ADAS calibration check so the forward camera and radar match the updated geometry. Depending on requirements, that may be a static target setup, a scan-tool guided dynamic road routine, or both. After any four-wheel alignment, ask if the shop performed a diagnostic pre-scan/post-scan and documented any required camera calibration, radar calibration, or steering angle reset. Skipping steps can show up as LKA that nudges off-center, ACC that behaves inconsistently, or alerts that seem late or overly sensitive. If you’re searching “Mazda CX-80 ADAS calibration after alignment” or “ADAS calibration near me,” choose a process that verifies alignment specs first and records calibration results.
Mazda CX-80 ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Mazda CX-80—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Mazda CX-80 set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Mazda CX-80 After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
It doesn’t take a major crash to push ADAS out of spec on a Mazda CX-80. A light rear-end, slow-speed bumper hit, or curb impact can transfer force into the bumper structure, sensor brackets, or windshield/camera area. Because radar and camera assemblies are aimed within very small tolerances, a tiny shift in a bracket, bumper reinforcement, or camera mount can change what the system “thinks” is straight ahead. The symptoms may be subtle: ACC that feels inconsistent, forward-collision warnings that seem early or late, lane-keeping that drifts, or intermittent false alerts. Often there is no warning light, so the reliable approach is to scan for stored codes and follow OEM calibration requirements. Post-impact best practice is a diagnostic pre-scan, any required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status. Save the calibration report with your repair paperwork, since insurers and future shops often ask for proof. If the incident also damaged your windshield—especially on Mazda CX-80 trims with windshield-mounted cameras—Bang AutoGlass can provide mobile replacement when scheduling allows. Most installs take 30–45 minutes; plan at least one hour of safe drive time for adhesive cure. We can also help you organize scan results and direct you to an appropriate calibration resource.
Signs Your Mazda CX-80 ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
If your Mazda CX-80 has ADAS, a warning light for the camera, radar, or lane assist is the obvious sign calibration may be needed. Many issues show up earlier as behavior that feels "off." Notice lane-keeping assist pulling you off-center, lane departure alerts firing too often, or lane-centering that wanders instead of holding steady. Adaptive cruise control (ACC) can also change: inconsistent following distance, abrupt braking, or unexpected speed changes may mean the camera or radar view is no longer aligned with the vehicle's centerline. Other clues include false forward-collision warnings or blind-spot monitoring that misses vehicles. If this started right after windshield replacement with a windshield-mounted camera, wheel alignment, suspension/steering work, bumper repair, or a minor hit, assume calibration prerequisites shifted. The fix is a scan for codes and an OEM-procedure static and/or dynamic calibration, documented with a calibration report. For searches like "Mazda CX-80 ADAS calibration near me," choose a shop that can scan, calibrate, and provide paperwork. If damaged glass is involved, Bang AutoGlass offers next-day mobile windshield replacement. Installs usually take 30-45 minutes plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
How Shops Confirm Mazda CX-80 ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
When a shop says your Mazda CX-80 ADAS is "good," ask what evidence supports that claim. The standard is an OEM-style process with paperwork. It typically begins with a pre-scan to find diagnostic trouble codes (DTCs) and module status across camera, radar, braking, and lane-assist systems, including history faults that may not trigger a warning light. Next, the shop confirms calibration prerequisites: correct tire size and pressure, proper ride height, no looseness in steering/suspension components, and alignment within spec (including thrust angle). Those checks matter because camera calibration and radar calibration assume the vehicle's geometry is correct. After prerequisites, procedure selection depends on your Mazda CX-80 trim and options. A windshield replacement, bumper repair, alignment, or suspension work may require target-based static calibration, a scan-tool initiated dynamic road routine, or both, sometimes across multiple systems (front camera, front radar, steering angle sensor reset). Once complete, a post-scan verifies normal status and cleared codes. Request the deliverables: pre-scan and post-scan printouts, alignment measurements if performed, and the ADAS calibration report showing completion and final pass status for insurance and your records.
Insurance and Warranty Questions for Mazda CX-80 ADAS Calibration: What’s Typically Covered and What to Document
With Mazda CX-80 ADAS calibration, reimbursement usually depends on the cause. Collision-related calibrations (bumper repair, sensor bracket replacement, suspension impact) are commonly billed under collision coverage. Calibrations required after windshield replacement on a Mazda CX-80 with a windshield-mounted camera are often handled under comprehensive coverage, especially when the camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Deductibles and carrier rules vary, so ask whether scanning and camera/radar calibration are reimbursable for your claim. Make the decision easy for the adjuster by keeping strong documentation: a repair order stating the trigger event, photos of the affected area, alignment printouts if alignment or ride height was part of the job, and both pre-scan and post-scan results. The key document is the ADAS calibration report showing the procedure performed and the final pass status. It also helps when invoices separate glass work, diagnostic scanning, and calibration labor. Bang AutoGlass supports the glass portion with mobile service (often as soon as next day when scheduling allows) and works with all insurers when comprehensive coverage applies. Windshield replacement typically takes 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and includes a lifetime workmanship warranty.
Services
Service Areas
Do You Need ADAS Calibration for Mazda CX-80 After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
On a Mazda CX-80, a wheel alignment affects more than steering feel and tire wear—it can also shift the reference angles your Advanced Driver Assistance Systems (ADAS) use for lane-keeping assist (LKA), lane departure warning (LDW), adaptive cruise control (ACC), and automatic emergency braking (AEB). These systems rely on the vehicle’s direction of travel (thrust angle) and a correct steering angle sensor (SAS) zero point to define “straight ahead.” When toe, camber, or caster is adjusted, the Mazda CX-80 may track on a slightly different line, and OEM procedures often call for a SAS reset and an ADAS calibration check so the forward camera and radar match the updated geometry. Depending on requirements, that may be a static target setup, a scan-tool guided dynamic road routine, or both. After any four-wheel alignment, ask if the shop performed a diagnostic pre-scan/post-scan and documented any required camera calibration, radar calibration, or steering angle reset. Skipping steps can show up as LKA that nudges off-center, ACC that behaves inconsistently, or alerts that seem late or overly sensitive. If you’re searching “Mazda CX-80 ADAS calibration after alignment” or “ADAS calibration near me,” choose a process that verifies alignment specs first and records calibration results.
Mazda CX-80 ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Mazda CX-80—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Mazda CX-80 set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Mazda CX-80 After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
It doesn’t take a major crash to push ADAS out of spec on a Mazda CX-80. A light rear-end, slow-speed bumper hit, or curb impact can transfer force into the bumper structure, sensor brackets, or windshield/camera area. Because radar and camera assemblies are aimed within very small tolerances, a tiny shift in a bracket, bumper reinforcement, or camera mount can change what the system “thinks” is straight ahead. The symptoms may be subtle: ACC that feels inconsistent, forward-collision warnings that seem early or late, lane-keeping that drifts, or intermittent false alerts. Often there is no warning light, so the reliable approach is to scan for stored codes and follow OEM calibration requirements. Post-impact best practice is a diagnostic pre-scan, any required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status. Save the calibration report with your repair paperwork, since insurers and future shops often ask for proof. If the incident also damaged your windshield—especially on Mazda CX-80 trims with windshield-mounted cameras—Bang AutoGlass can provide mobile replacement when scheduling allows. Most installs take 30–45 minutes; plan at least one hour of safe drive time for adhesive cure. We can also help you organize scan results and direct you to an appropriate calibration resource.
Signs Your Mazda CX-80 ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
If your Mazda CX-80 has ADAS, a warning light for the camera, radar, or lane assist is the obvious sign calibration may be needed. Many issues show up earlier as behavior that feels "off." Notice lane-keeping assist pulling you off-center, lane departure alerts firing too often, or lane-centering that wanders instead of holding steady. Adaptive cruise control (ACC) can also change: inconsistent following distance, abrupt braking, or unexpected speed changes may mean the camera or radar view is no longer aligned with the vehicle's centerline. Other clues include false forward-collision warnings or blind-spot monitoring that misses vehicles. If this started right after windshield replacement with a windshield-mounted camera, wheel alignment, suspension/steering work, bumper repair, or a minor hit, assume calibration prerequisites shifted. The fix is a scan for codes and an OEM-procedure static and/or dynamic calibration, documented with a calibration report. For searches like "Mazda CX-80 ADAS calibration near me," choose a shop that can scan, calibrate, and provide paperwork. If damaged glass is involved, Bang AutoGlass offers next-day mobile windshield replacement. Installs usually take 30-45 minutes plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
How Shops Confirm Mazda CX-80 ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
When a shop says your Mazda CX-80 ADAS is "good," ask what evidence supports that claim. The standard is an OEM-style process with paperwork. It typically begins with a pre-scan to find diagnostic trouble codes (DTCs) and module status across camera, radar, braking, and lane-assist systems, including history faults that may not trigger a warning light. Next, the shop confirms calibration prerequisites: correct tire size and pressure, proper ride height, no looseness in steering/suspension components, and alignment within spec (including thrust angle). Those checks matter because camera calibration and radar calibration assume the vehicle's geometry is correct. After prerequisites, procedure selection depends on your Mazda CX-80 trim and options. A windshield replacement, bumper repair, alignment, or suspension work may require target-based static calibration, a scan-tool initiated dynamic road routine, or both, sometimes across multiple systems (front camera, front radar, steering angle sensor reset). Once complete, a post-scan verifies normal status and cleared codes. Request the deliverables: pre-scan and post-scan printouts, alignment measurements if performed, and the ADAS calibration report showing completion and final pass status for insurance and your records.
Insurance and Warranty Questions for Mazda CX-80 ADAS Calibration: What’s Typically Covered and What to Document
With Mazda CX-80 ADAS calibration, reimbursement usually depends on the cause. Collision-related calibrations (bumper repair, sensor bracket replacement, suspension impact) are commonly billed under collision coverage. Calibrations required after windshield replacement on a Mazda CX-80 with a windshield-mounted camera are often handled under comprehensive coverage, especially when the camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Deductibles and carrier rules vary, so ask whether scanning and camera/radar calibration are reimbursable for your claim. Make the decision easy for the adjuster by keeping strong documentation: a repair order stating the trigger event, photos of the affected area, alignment printouts if alignment or ride height was part of the job, and both pre-scan and post-scan results. The key document is the ADAS calibration report showing the procedure performed and the final pass status. It also helps when invoices separate glass work, diagnostic scanning, and calibration labor. Bang AutoGlass supports the glass portion with mobile service (often as soon as next day when scheduling allows) and works with all insurers when comprehensive coverage applies. Windshield replacement typically takes 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and includes a lifetime workmanship warranty.
Enjoy More Relevant Blogs
How Much Does ADAS Calibration Cost for Mazda CX-80? What Drives Pricing and What Insurance Typically Covers
How much does ADAS calibration cost for a Mazda CX-80? Learn pricing drivers, camera vs radar needs, labor time, and what insurance typically covers.
OEM Calibration Requirements for Mazda CX-80: How to Confirm What Must Be Calibrated
OEM calibration requirements for Mazda CX-80: how to confirm what must be calibrated after repairs, what triggers recalibration, and what proof to ask for.
Mobile ADAS Calibration for Mazda CX-80: What to Expect On-Site and Why Setup Matters
Mobile ADAS calibration for Mazda CX-80: what to expect on-site, space and lighting needs, and why setup and verification matter after repairs today.
How to Schedule ADAS Calibration for Mazda CX-80 After Windshield Replacement
Schedule ADAS calibration for Mazda CX-80 after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
Camera Calibration for Mazda CX-80: Lane Assist and Forward Collision Accuracy Explained
Need camera calibration for your Mazda CX-80? See how calibration affects lane assist and forward collision accuracy after windshield service or repairs.
ADAS Calibration Checklist for Mazda CX-80: Documentation, Verification, and Final Safety Checks
ADAS calibration checklist for Mazda CX-80: documentation to request, scans to verify, and safety checks that confirm cameras and sensors are set right.
Static vs Dynamic ADAS Calibration for Mazda CX-80: What the Difference Means
Static vs dynamic ADAS calibration for Mazda CX-80: key differences, when each is required, how long it takes, and what affects accuracy for safety.
Pre- and Post-Calibration Scans for Mazda CX-80: Proving Systems Are Set Correctly
Pre- and post-calibration scans for Mazda CX-80: see why scans matter, what they verify, and how reports prove ADAS systems are set correctly after service.
ADAS Warning Lights on Mazda CX-80: When Calibration Is the Fix and When It’s Not
ADAS warning lights on your Mazda CX-80? Learn when calibration fixes lane assist or AEB issues, when it will not, and what to check next. Schedule help.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm