Services
Service Areas
Shattered Back Window on Rolls-Royce Ghost: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Rolls-Royce Ghost: Safety, Visibility, and Securing the Vehicle
A shattered rear window on your Rolls-Royce Ghost is urgent, but the right steps prevent injuries and limit secondary damage. If the glass breaks while driving, slow down gradually, activate hazard lights, and park in a safe spot away from traffic. Do not sweep glass with bare hands. Tempered back glass breaks into small pellets that can cling to clothing and hide in seat seams, so keep passengers from leaning into the opening and keep kids and pets out until cleanup is underway. If you must move the vehicle, clear the rear deck so pieces do not slide forward under braking. Remove any loose chunks hanging in the frame, but leave stubborn fragments for the installer. Then cover the opening from the outside with plastic sheeting and painter's tape to reduce water intrusion and deter theft. Avoid slamming doors or closing all windows with high HVAC pressure, since pressure pulses can pop remaining shards free. Take photos for your insurance claim; comprehensive coverage often applies to rear glass. Bang AutoGlass can then complete mobile Rolls-Royce Ghost back glass replacement, often as soon as next day. Installation typically takes 30-45 minutes, followed by at least 1 hour of urethane cure time, and every job includes our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A broken rear window means your Rolls-Royce Ghost likely has glass in the rear deck, seat seams, and trunk/cargo area. Clean it in stages so you do not drive shards deeper into upholstery. Put on safety glasses, thick gloves, and sturdy shoes, and keep unprotected passengers out of the work area. If available, lay plastic sheeting over seats and the cargo floor before you start lifting pieces. Start with big fragments. Pick larger chunks from the window frame and rear deck and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong vacuum using a crevice tool. Follow a top-down route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk well, including the spare-tire compartment. After the first vacuum, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from fabric and corners; repeat until the tape comes back clean. Finish by wiping plastics with a slightly damp microfiber towel rather than scrubbing. If you have mobile rear glass replacement scheduled with Bang AutoGlass, clear loose debris around the opening so the bond area stays clean.
Confirm the Correct Rear Glass for Rolls-Royce Ghost: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Ordering the rear glass for a Rolls-Royce Ghost starts with matching the vehicle's options. Begin with the rear defroster: most Rolls-Royce Ghost back windows use a printed heating grid, and the replacement must match the layout and have the connector tabs so it plugs into the factory harness. Also confirm antenna features. Many vehicles integrate AM/FM, GPS, or cellular traces into the rear window; if your reception depended on the original glass, you need an antenna-equipped replacement. Next, match tint and privacy shading. Rear glass may be clear, lightly tinted, or privacy glass. Matching shade matters for appearance, heat rejection, and (by state) compliance. If your Rolls-Royce Ghost had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after rear windshield replacement. Finally, verify markings and fit. Automotive glass carries DOT identification and AS markings (AS2/AS3 are common on rear and side glass and can indicate tinted variations). VIN validation and the part number help ensure proper curvature, tempered-glass performance, and an insurance-friendly repair. Bang AutoGlass verifies these details before dispatching our mobile team, and every install is backed by our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
Removal and preparation are the foundation of a leak-free rear window replacement on your Rolls-Royce Ghost. We start with containment: seats, the rear deck, and the cargo area are covered so glass pellets and adhesive debris don't contaminate the interior. Trim, fasteners, and moldings are removed in the proper sequence to protect clips and keep the opening accessible, and defroster/antenna leads are secured so wiring isn't strained. Next, the old urethane is cut and reduced to create a stable bonding surface. Standard methods remove most cured adhesive while leaving an even base layer (about 1-2 mm) so new urethane bonds to existing urethane rather than bare metal. We inspect the pinchweld for scratches through paint, rust, contamination, or misalignment from prior repairs, then treat, prime, and seal any exposed metal because corrosion under the bond line can cause leaks and adhesion loss. Before installation, we dry-fit the replacement rear glass for your Rolls-Royce Ghost, confirm molding and spacer condition, clean the frit and aperture, and apply the correct primer/activator with proper flash times. This prep discipline lets Bang AutoGlass set the glass evenly and deliver mobile, next-day rear glass replacement backed by a lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Rolls-Royce Ghost: What Controls Safe Release
For your Rolls-Royce Ghost rear windshield replacement, urethane curing is the gating factor for safe release. The adhesive that holds the back glass is a high-strength urethane system, and each product has a documented Safe Drive-Away Time (SDAT). SDAT depends on formulation and, critically, installation conditions and process control. Temperature and humidity influence moisture-cure speed: cold temperatures and very dry air can slow cure, while warm, humid conditions usually shorten it. Primers must be applied to the correct surfaces, flash times must be respected, and the glass must be set within the urethane's open time. Bond integrity is also mechanical: a consistent bead profile and uniform set-down pressure compress the bead evenly around the perimeter, creating a continuous seal without thin spots. Contamination-dust, oils, or silicone dressings-can interfere with adhesion and lead to leaks or wind noise. Bare-metal scratches or corrosion on the pinchweld must be treated and primed because rust under the bond line is a common long-term failure point. Bang AutoGlass usually completes a Rolls-Royce Ghost rear glass replacement in 30-45 minutes, then recommends a minimum of 1 hour before safe drive-away. Avoid slamming doors and skip automated car washes for the first day; if conditions warrant, we'll extend cure time, backed by our lifetime workmanship warranty.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Rolls-Royce Ghost rear window replacement is installed, verification confirms the glass is correct, sealed, and functional. First, check electrical features: rear defroster connectors should be firmly seated on the tabs, and any in-glass antenna leads should be reconnected and strain-relieved so hatch or trunk movement won't tug the wiring. A quick function check helps you avoid discovering a loose connection or weak reception later. Next, validate sealing and wind noise. The molding and reveal line should be even, with consistent spacing around the perimeter. We perform a controlled perimeter water test to confirm there are no leaks, and when practical a short road test to replicate highway airflow; a whistle usually points to a small gap or mis-seated molding. As a simple owner check after rain, look for damp headliner edges or moisture in the cargo area. Finally, keep documentation: you should receive an invoice, warranty record, and notes on the rear glass installed for your Rolls-Royce Ghost (tint, defroster grid, antenna integration, and DOT/AS markings). Bang AutoGlass backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Services
Service Areas
Shattered Back Window on Rolls-Royce Ghost: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Rolls-Royce Ghost: Safety, Visibility, and Securing the Vehicle
A shattered rear window on your Rolls-Royce Ghost is urgent, but the right steps prevent injuries and limit secondary damage. If the glass breaks while driving, slow down gradually, activate hazard lights, and park in a safe spot away from traffic. Do not sweep glass with bare hands. Tempered back glass breaks into small pellets that can cling to clothing and hide in seat seams, so keep passengers from leaning into the opening and keep kids and pets out until cleanup is underway. If you must move the vehicle, clear the rear deck so pieces do not slide forward under braking. Remove any loose chunks hanging in the frame, but leave stubborn fragments for the installer. Then cover the opening from the outside with plastic sheeting and painter's tape to reduce water intrusion and deter theft. Avoid slamming doors or closing all windows with high HVAC pressure, since pressure pulses can pop remaining shards free. Take photos for your insurance claim; comprehensive coverage often applies to rear glass. Bang AutoGlass can then complete mobile Rolls-Royce Ghost back glass replacement, often as soon as next day. Installation typically takes 30-45 minutes, followed by at least 1 hour of urethane cure time, and every job includes our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A broken rear window means your Rolls-Royce Ghost likely has glass in the rear deck, seat seams, and trunk/cargo area. Clean it in stages so you do not drive shards deeper into upholstery. Put on safety glasses, thick gloves, and sturdy shoes, and keep unprotected passengers out of the work area. If available, lay plastic sheeting over seats and the cargo floor before you start lifting pieces. Start with big fragments. Pick larger chunks from the window frame and rear deck and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong vacuum using a crevice tool. Follow a top-down route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk well, including the spare-tire compartment. After the first vacuum, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from fabric and corners; repeat until the tape comes back clean. Finish by wiping plastics with a slightly damp microfiber towel rather than scrubbing. If you have mobile rear glass replacement scheduled with Bang AutoGlass, clear loose debris around the opening so the bond area stays clean.
Confirm the Correct Rear Glass for Rolls-Royce Ghost: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Ordering the rear glass for a Rolls-Royce Ghost starts with matching the vehicle's options. Begin with the rear defroster: most Rolls-Royce Ghost back windows use a printed heating grid, and the replacement must match the layout and have the connector tabs so it plugs into the factory harness. Also confirm antenna features. Many vehicles integrate AM/FM, GPS, or cellular traces into the rear window; if your reception depended on the original glass, you need an antenna-equipped replacement. Next, match tint and privacy shading. Rear glass may be clear, lightly tinted, or privacy glass. Matching shade matters for appearance, heat rejection, and (by state) compliance. If your Rolls-Royce Ghost had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after rear windshield replacement. Finally, verify markings and fit. Automotive glass carries DOT identification and AS markings (AS2/AS3 are common on rear and side glass and can indicate tinted variations). VIN validation and the part number help ensure proper curvature, tempered-glass performance, and an insurance-friendly repair. Bang AutoGlass verifies these details before dispatching our mobile team, and every install is backed by our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
Removal and preparation are the foundation of a leak-free rear window replacement on your Rolls-Royce Ghost. We start with containment: seats, the rear deck, and the cargo area are covered so glass pellets and adhesive debris don't contaminate the interior. Trim, fasteners, and moldings are removed in the proper sequence to protect clips and keep the opening accessible, and defroster/antenna leads are secured so wiring isn't strained. Next, the old urethane is cut and reduced to create a stable bonding surface. Standard methods remove most cured adhesive while leaving an even base layer (about 1-2 mm) so new urethane bonds to existing urethane rather than bare metal. We inspect the pinchweld for scratches through paint, rust, contamination, or misalignment from prior repairs, then treat, prime, and seal any exposed metal because corrosion under the bond line can cause leaks and adhesion loss. Before installation, we dry-fit the replacement rear glass for your Rolls-Royce Ghost, confirm molding and spacer condition, clean the frit and aperture, and apply the correct primer/activator with proper flash times. This prep discipline lets Bang AutoGlass set the glass evenly and deliver mobile, next-day rear glass replacement backed by a lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Rolls-Royce Ghost: What Controls Safe Release
For your Rolls-Royce Ghost rear windshield replacement, urethane curing is the gating factor for safe release. The adhesive that holds the back glass is a high-strength urethane system, and each product has a documented Safe Drive-Away Time (SDAT). SDAT depends on formulation and, critically, installation conditions and process control. Temperature and humidity influence moisture-cure speed: cold temperatures and very dry air can slow cure, while warm, humid conditions usually shorten it. Primers must be applied to the correct surfaces, flash times must be respected, and the glass must be set within the urethane's open time. Bond integrity is also mechanical: a consistent bead profile and uniform set-down pressure compress the bead evenly around the perimeter, creating a continuous seal without thin spots. Contamination-dust, oils, or silicone dressings-can interfere with adhesion and lead to leaks or wind noise. Bare-metal scratches or corrosion on the pinchweld must be treated and primed because rust under the bond line is a common long-term failure point. Bang AutoGlass usually completes a Rolls-Royce Ghost rear glass replacement in 30-45 minutes, then recommends a minimum of 1 hour before safe drive-away. Avoid slamming doors and skip automated car washes for the first day; if conditions warrant, we'll extend cure time, backed by our lifetime workmanship warranty.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Rolls-Royce Ghost rear window replacement is installed, verification confirms the glass is correct, sealed, and functional. First, check electrical features: rear defroster connectors should be firmly seated on the tabs, and any in-glass antenna leads should be reconnected and strain-relieved so hatch or trunk movement won't tug the wiring. A quick function check helps you avoid discovering a loose connection or weak reception later. Next, validate sealing and wind noise. The molding and reveal line should be even, with consistent spacing around the perimeter. We perform a controlled perimeter water test to confirm there are no leaks, and when practical a short road test to replicate highway airflow; a whistle usually points to a small gap or mis-seated molding. As a simple owner check after rain, look for damp headliner edges or moisture in the cargo area. Finally, keep documentation: you should receive an invoice, warranty record, and notes on the rear glass installed for your Rolls-Royce Ghost (tint, defroster grid, antenna integration, and DOT/AS markings). Bang AutoGlass backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Services
Service Areas
Shattered Back Window on Rolls-Royce Ghost: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Rolls-Royce Ghost: Safety, Visibility, and Securing the Vehicle
A shattered rear window on your Rolls-Royce Ghost is urgent, but the right steps prevent injuries and limit secondary damage. If the glass breaks while driving, slow down gradually, activate hazard lights, and park in a safe spot away from traffic. Do not sweep glass with bare hands. Tempered back glass breaks into small pellets that can cling to clothing and hide in seat seams, so keep passengers from leaning into the opening and keep kids and pets out until cleanup is underway. If you must move the vehicle, clear the rear deck so pieces do not slide forward under braking. Remove any loose chunks hanging in the frame, but leave stubborn fragments for the installer. Then cover the opening from the outside with plastic sheeting and painter's tape to reduce water intrusion and deter theft. Avoid slamming doors or closing all windows with high HVAC pressure, since pressure pulses can pop remaining shards free. Take photos for your insurance claim; comprehensive coverage often applies to rear glass. Bang AutoGlass can then complete mobile Rolls-Royce Ghost back glass replacement, often as soon as next day. Installation typically takes 30-45 minutes, followed by at least 1 hour of urethane cure time, and every job includes our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A broken rear window means your Rolls-Royce Ghost likely has glass in the rear deck, seat seams, and trunk/cargo area. Clean it in stages so you do not drive shards deeper into upholstery. Put on safety glasses, thick gloves, and sturdy shoes, and keep unprotected passengers out of the work area. If available, lay plastic sheeting over seats and the cargo floor before you start lifting pieces. Start with big fragments. Pick larger chunks from the window frame and rear deck and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong vacuum using a crevice tool. Follow a top-down route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk well, including the spare-tire compartment. After the first vacuum, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from fabric and corners; repeat until the tape comes back clean. Finish by wiping plastics with a slightly damp microfiber towel rather than scrubbing. If you have mobile rear glass replacement scheduled with Bang AutoGlass, clear loose debris around the opening so the bond area stays clean.
Confirm the Correct Rear Glass for Rolls-Royce Ghost: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Ordering the rear glass for a Rolls-Royce Ghost starts with matching the vehicle's options. Begin with the rear defroster: most Rolls-Royce Ghost back windows use a printed heating grid, and the replacement must match the layout and have the connector tabs so it plugs into the factory harness. Also confirm antenna features. Many vehicles integrate AM/FM, GPS, or cellular traces into the rear window; if your reception depended on the original glass, you need an antenna-equipped replacement. Next, match tint and privacy shading. Rear glass may be clear, lightly tinted, or privacy glass. Matching shade matters for appearance, heat rejection, and (by state) compliance. If your Rolls-Royce Ghost had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after rear windshield replacement. Finally, verify markings and fit. Automotive glass carries DOT identification and AS markings (AS2/AS3 are common on rear and side glass and can indicate tinted variations). VIN validation and the part number help ensure proper curvature, tempered-glass performance, and an insurance-friendly repair. Bang AutoGlass verifies these details before dispatching our mobile team, and every install is backed by our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
Removal and preparation are the foundation of a leak-free rear window replacement on your Rolls-Royce Ghost. We start with containment: seats, the rear deck, and the cargo area are covered so glass pellets and adhesive debris don't contaminate the interior. Trim, fasteners, and moldings are removed in the proper sequence to protect clips and keep the opening accessible, and defroster/antenna leads are secured so wiring isn't strained. Next, the old urethane is cut and reduced to create a stable bonding surface. Standard methods remove most cured adhesive while leaving an even base layer (about 1-2 mm) so new urethane bonds to existing urethane rather than bare metal. We inspect the pinchweld for scratches through paint, rust, contamination, or misalignment from prior repairs, then treat, prime, and seal any exposed metal because corrosion under the bond line can cause leaks and adhesion loss. Before installation, we dry-fit the replacement rear glass for your Rolls-Royce Ghost, confirm molding and spacer condition, clean the frit and aperture, and apply the correct primer/activator with proper flash times. This prep discipline lets Bang AutoGlass set the glass evenly and deliver mobile, next-day rear glass replacement backed by a lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Rolls-Royce Ghost: What Controls Safe Release
For your Rolls-Royce Ghost rear windshield replacement, urethane curing is the gating factor for safe release. The adhesive that holds the back glass is a high-strength urethane system, and each product has a documented Safe Drive-Away Time (SDAT). SDAT depends on formulation and, critically, installation conditions and process control. Temperature and humidity influence moisture-cure speed: cold temperatures and very dry air can slow cure, while warm, humid conditions usually shorten it. Primers must be applied to the correct surfaces, flash times must be respected, and the glass must be set within the urethane's open time. Bond integrity is also mechanical: a consistent bead profile and uniform set-down pressure compress the bead evenly around the perimeter, creating a continuous seal without thin spots. Contamination-dust, oils, or silicone dressings-can interfere with adhesion and lead to leaks or wind noise. Bare-metal scratches or corrosion on the pinchweld must be treated and primed because rust under the bond line is a common long-term failure point. Bang AutoGlass usually completes a Rolls-Royce Ghost rear glass replacement in 30-45 minutes, then recommends a minimum of 1 hour before safe drive-away. Avoid slamming doors and skip automated car washes for the first day; if conditions warrant, we'll extend cure time, backed by our lifetime workmanship warranty.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Rolls-Royce Ghost rear window replacement is installed, verification confirms the glass is correct, sealed, and functional. First, check electrical features: rear defroster connectors should be firmly seated on the tabs, and any in-glass antenna leads should be reconnected and strain-relieved so hatch or trunk movement won't tug the wiring. A quick function check helps you avoid discovering a loose connection or weak reception later. Next, validate sealing and wind noise. The molding and reveal line should be even, with consistent spacing around the perimeter. We perform a controlled perimeter water test to confirm there are no leaks, and when practical a short road test to replicate highway airflow; a whistle usually points to a small gap or mis-seated molding. As a simple owner check after rain, look for damp headliner edges or moisture in the cargo area. Finally, keep documentation: you should receive an invoice, warranty record, and notes on the rear glass installed for your Rolls-Royce Ghost (tint, defroster grid, antenna integration, and DOT/AS markings). Bang AutoGlass backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Enjoy More Relevant Blogs
Back Glass Replacement on Rolls-Royce Ghost: Defroster Tabs, Antenna Lines, and Connector Reattachment Basics
Back glass replacement on Rolls-Royce Ghost: defroster tabs, antenna lines, and connectors explained, plus install tips to avoid damage and rework safely.
How to Schedule Mobile Rear Glass Replacement for Rolls-Royce Ghost
Schedule mobile rear glass replacement for your Rolls-Royce Ghost in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Tempered Safety Rear Glass Replacement for Rolls-Royce Ghost: Understanding DOT Markings and FMVSS 205
Need Rolls-Royce Ghost rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Post-Install Checks for Rolls-Royce Ghost: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Rolls-Royce Ghost: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
How Much Does Rear Glass Replacement Cost for Rolls-Royce Ghost? Pricing Factors, OEM vs Aftermarket, and Insurance Deductibles
Estimate Rolls-Royce Ghost rear glass replacement cost. Compare OEM vs aftermarket, labor factors, insurance deductibles, and ways to save. Request a quote.
OEM-Quality Rear Glass Replacement for Rolls-Royce Ghost: Defroster Grid and Tint-Match Checklist
OEM-quality rear glass replacement for Rolls-Royce Ghost: defroster grid and tint-match checklist, plus install tips to avoid callbacks—schedule service.
Rear Defroster Not Working on Rolls-Royce Ghost? When Rear Glass Replacement Makes More Sense Than Repair
Rear defroster not working on your Rolls-Royce Ghost? Learn common causes, when repair fails, and when rear glass replacement is the smarter fix for winter.
How Long Does Rear Glass Replacement Take on Rolls-Royce Ghost? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How long is Rolls-Royce Ghost rear glass replacement? Get install time, urethane cure guidelines, and drive-away timing after service. Plan your visit today.
Rear Glass Replacement for Rolls-Royce Ghost: What to Expect During Install and Aftercare
Rear glass replacement for Rolls-Royce Ghost: what happens during install, defroster and tint considerations, cure time, and aftercare to prevent leaks long-term.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm