Services
Service Areas
Sunroof vs Moonroof on Subaru Exiga Crossover 7: How to Order the Correct Roof Glass Replacement
Sunroof vs Moonroof on Subaru Exiga Crossover 7: Terminology vs Actual Roof Design
When people search sunroof vs moonroof for a Subaru Exiga Crossover 7, they want a definition, but the right roof glass replacement depends on the roof design, not the name. Older usage called an opaque tilting or sliding panel a sunroof and a tinted glass panel with a sunshade a moonroof, yet many OEMs now use the terms interchangeably. For correct sunroof glass replacement or moonroof glass replacement, confirm what you have: fixed roof glass vs an operable panel, vent only vs vent and slide, slides above the roof spoiler style vs retracts into the roof pocket, and single panel vs panoramic roof glass with multiple panels. These details determine curvature, mounting tabs, track interface, seals, and flush fit. Bang AutoGlass verifies fitment before ordering. If you are unsure, take photos outside and inside with the roof closed, vented, and open, and note how the panel travels. We can confirm the correct roof glass for your Subaru Exiga Crossover 7 and schedule mobile replacement as soon as next day. Most installs take 30-45 minutes; allow at least one hour of cure time before safe drive away. Every job includes a lifetime workmanship warranty.
Identify Your Roof Type Before Ordering: Pop-Up, Tilt/Slide, and Panoramic on Subaru Exiga Crossover 7
Before ordering roof glass replacement for a Subaru Exiga Crossover 7, identify the roof type by how the panel opens and where it stores, because sunroof glass is not one size fits all. Pop up roofs are simplest: the panel tilts for ventilation, is often manual, and uses basic hinge or latch hardware. Tilt and slide spoiler roofs vent first, then slide rearward above the roof skin; the glass stays visible and you usually see side rails. In built sliding roofs also vent, but then retract into a pocket between the roof and headliner, changing the glass edge and attachment points. Panoramic roofs add complexity with multiple panels, larger frames, and specific drain routing, often a fixed rear section plus a movable front section. Also confirm factory vs aftermarket. Aftermarket roofs often show a trim ring and raised cutout lip, while factory systems sit more flush and rely on OEM specific tabs. Checklist for your Subaru Exiga Crossover 7: watch the first motion, count panels, note manual vs powered shade, and photograph the tracks, wind deflector area, and perimeter seal. Bang AutoGlass can verify fitment and handle mobile sunroof glass replacement, moonroof glass replacement, or panoramic roof glass replacement as soon as next day.
Get the Right Part Number: VIN, Trim Level, Model Year, and Build Variations for Subaru Exiga Crossover 7
Ordering roof glass replacement for a Subaru Exiga Crossover 7 is a part number exercise, and the correct option can vary even within the same model year. Begin with the VIN, because glass databases use it to confirm generation, submodel, and option codes that are easy to miss online. Then confirm trim and roof package: fixed glass, power tilt and slide, and panoramic multi panel assemblies are usually separate listings. Next, look for production breaks. Check the driver door jamb build date and compare it to catalog notes that specify from and to ranges or VIN serial breakpoints. Mid year plant or supplier changes can alter curvature, thickness, or mounting tab layout, so two same year Subaru Exiga Crossover 7 vehicles can legitimately use different sunroof glass or moonroof glass. A final cross check is visual: photograph the glass edge, tabs, and the track interface, and note whether the panel slides above the roof or retracts inward. If you want an end to end solution, Bang AutoGlass can verify fitment, source the correct part, and perform mobile replacement as soon as next day. Most installs take 30-45 minutes; allow one hour cure time before safe drive away. Every job is backed by a lifetime workmanship warranty.
Match the Glass Features: Tint/Privacy Shade, Coatings, and Factory Options on Subaru Exiga Crossover 7
Choosing roof glass for a Subaru Exiga Crossover 7 isn’t only about calling it a sunroof or moonroof; it’s about ordering the exact factory configuration. Start with the obvious: tint level and whether the interior shade is manual or powered, because shade tracks and clearances vary by package. Then confirm solar-control technology. Many roof panels are laminated with UV- and IR-filtering interlayers, and those layers can affect color, gloss, and reflectivity. Next, match the edge treatment. The black frit border and dot-matrix are baked-on ceramic layers that shield the urethane bond and seals from UV and create a stable bonding surface, so the frit placement and edge profile should mirror your original Subaru Exiga Crossover 7 glass. Also verify tempered versus laminated construction and thickness; some laminated panels include acoustic layers to cut wind noise. Finally, account for options that drive different parts: panoramic multi-panel systems, integrated shade rails, sensors or antenna provisions on certain trims, and roof curvature differences across builds. Getting tint, coatings, frit pattern, and construction right helps you avoid common fitment and appearance issues in sunroof glass replacement and panoramic roof glass replacement. Bang AutoGlass can confirm the specs and complete mobile roof glass installation as soon as next day.
Verify Safety Markings: DOT Symbol, Manufacturer Code, and FMVSS 205 Compliance
Before installing roof glass on a Subaru Exiga Crossover 7, verify the permanent safety markings. In the U.S., FMVSS 205 (49 CFR 571.205) governs automotive glazing and incorporates labeling requirements through ANSI/SAE Z26.1, so reputable replacement roof glass will have an etched manufacturer “bug,” not just a sticker. Look for the DOT code (DOT plus a number) that identifies the glazing manufacturer, along with additional codes used for traceability. Many pieces also show an AS classification (often AS1, AS2, or AS3) that reflects glazing category and typical placement based on light transmission, and the etching may indicate tempered versus laminated construction. Some roof panels also carry international marks such as ECE R43 when produced for multiple markets. You may see an “M” number or internal variant code that differentiates tint shade, thickness, or coatings—helpful for matching like-for-like features on your Subaru Exiga Crossover 7. The goal is simple: confirm the replacement roof glass is clearly marked, readable, and consistent with the original glass type and features. Missing or suspicious markings are a red flag for compliance and reliability in sunroof glass replacement, moonroof glass replacement, and panoramic roof glass replacement. Bang AutoGlass can confirm the markings and complete mobile roof glass replacement as soon as next day.
Order-Ready Checklist: Frame, Seals, Deflector, and Hardware Notes That Prevent Reorders
To avoid a reorder on a Subaru Exiga Crossover 7 roof glass replacement, treat the roof as a system—not just a panel. Start by confirming whether you need glass-only or a full assembly/cassette. On many roofs, the glass bolts to hinge blocks, lift arms, and mounting brackets; if any are bent, cracked, or missing, even the correct glass can sit high, bind, or leak. If you’re reusing hardware, photograph and mark hinge-block positions and adjustment points so the new panel returns to the same alignment references. Next, inspect perimeter seals and secondary gaskets for tears, flattening, or shrinkage, since worn seals are a top cause of wind noise and water intrusion. Check the wind deflector (arms, clips, springs) and verify drains are clear. Finally, confirm the “small parts” that derail installs: correct fasteners, intact guide shoes, undamaged trim rings, and matching tabs. Note any prior aftermarket modifications or evidence of previous adhesive work so installation planning is realistic. For end-to-end verification, Bang AutoGlass can confirm the right parts and perform mobile service as soon as next day. Most replacements take 30–45 minutes; allow at least one hour of cure time before drive-away. Every job is backed by our lifetime workmanship warranty.
Services
Service Areas
Sunroof vs Moonroof on Subaru Exiga Crossover 7: How to Order the Correct Roof Glass Replacement
Sunroof vs Moonroof on Subaru Exiga Crossover 7: Terminology vs Actual Roof Design
When people search sunroof vs moonroof for a Subaru Exiga Crossover 7, they want a definition, but the right roof glass replacement depends on the roof design, not the name. Older usage called an opaque tilting or sliding panel a sunroof and a tinted glass panel with a sunshade a moonroof, yet many OEMs now use the terms interchangeably. For correct sunroof glass replacement or moonroof glass replacement, confirm what you have: fixed roof glass vs an operable panel, vent only vs vent and slide, slides above the roof spoiler style vs retracts into the roof pocket, and single panel vs panoramic roof glass with multiple panels. These details determine curvature, mounting tabs, track interface, seals, and flush fit. Bang AutoGlass verifies fitment before ordering. If you are unsure, take photos outside and inside with the roof closed, vented, and open, and note how the panel travels. We can confirm the correct roof glass for your Subaru Exiga Crossover 7 and schedule mobile replacement as soon as next day. Most installs take 30-45 minutes; allow at least one hour of cure time before safe drive away. Every job includes a lifetime workmanship warranty.
Identify Your Roof Type Before Ordering: Pop-Up, Tilt/Slide, and Panoramic on Subaru Exiga Crossover 7
Before ordering roof glass replacement for a Subaru Exiga Crossover 7, identify the roof type by how the panel opens and where it stores, because sunroof glass is not one size fits all. Pop up roofs are simplest: the panel tilts for ventilation, is often manual, and uses basic hinge or latch hardware. Tilt and slide spoiler roofs vent first, then slide rearward above the roof skin; the glass stays visible and you usually see side rails. In built sliding roofs also vent, but then retract into a pocket between the roof and headliner, changing the glass edge and attachment points. Panoramic roofs add complexity with multiple panels, larger frames, and specific drain routing, often a fixed rear section plus a movable front section. Also confirm factory vs aftermarket. Aftermarket roofs often show a trim ring and raised cutout lip, while factory systems sit more flush and rely on OEM specific tabs. Checklist for your Subaru Exiga Crossover 7: watch the first motion, count panels, note manual vs powered shade, and photograph the tracks, wind deflector area, and perimeter seal. Bang AutoGlass can verify fitment and handle mobile sunroof glass replacement, moonroof glass replacement, or panoramic roof glass replacement as soon as next day.
Get the Right Part Number: VIN, Trim Level, Model Year, and Build Variations for Subaru Exiga Crossover 7
Ordering roof glass replacement for a Subaru Exiga Crossover 7 is a part number exercise, and the correct option can vary even within the same model year. Begin with the VIN, because glass databases use it to confirm generation, submodel, and option codes that are easy to miss online. Then confirm trim and roof package: fixed glass, power tilt and slide, and panoramic multi panel assemblies are usually separate listings. Next, look for production breaks. Check the driver door jamb build date and compare it to catalog notes that specify from and to ranges or VIN serial breakpoints. Mid year plant or supplier changes can alter curvature, thickness, or mounting tab layout, so two same year Subaru Exiga Crossover 7 vehicles can legitimately use different sunroof glass or moonroof glass. A final cross check is visual: photograph the glass edge, tabs, and the track interface, and note whether the panel slides above the roof or retracts inward. If you want an end to end solution, Bang AutoGlass can verify fitment, source the correct part, and perform mobile replacement as soon as next day. Most installs take 30-45 minutes; allow one hour cure time before safe drive away. Every job is backed by a lifetime workmanship warranty.
Match the Glass Features: Tint/Privacy Shade, Coatings, and Factory Options on Subaru Exiga Crossover 7
Choosing roof glass for a Subaru Exiga Crossover 7 isn’t only about calling it a sunroof or moonroof; it’s about ordering the exact factory configuration. Start with the obvious: tint level and whether the interior shade is manual or powered, because shade tracks and clearances vary by package. Then confirm solar-control technology. Many roof panels are laminated with UV- and IR-filtering interlayers, and those layers can affect color, gloss, and reflectivity. Next, match the edge treatment. The black frit border and dot-matrix are baked-on ceramic layers that shield the urethane bond and seals from UV and create a stable bonding surface, so the frit placement and edge profile should mirror your original Subaru Exiga Crossover 7 glass. Also verify tempered versus laminated construction and thickness; some laminated panels include acoustic layers to cut wind noise. Finally, account for options that drive different parts: panoramic multi-panel systems, integrated shade rails, sensors or antenna provisions on certain trims, and roof curvature differences across builds. Getting tint, coatings, frit pattern, and construction right helps you avoid common fitment and appearance issues in sunroof glass replacement and panoramic roof glass replacement. Bang AutoGlass can confirm the specs and complete mobile roof glass installation as soon as next day.
Verify Safety Markings: DOT Symbol, Manufacturer Code, and FMVSS 205 Compliance
Before installing roof glass on a Subaru Exiga Crossover 7, verify the permanent safety markings. In the U.S., FMVSS 205 (49 CFR 571.205) governs automotive glazing and incorporates labeling requirements through ANSI/SAE Z26.1, so reputable replacement roof glass will have an etched manufacturer “bug,” not just a sticker. Look for the DOT code (DOT plus a number) that identifies the glazing manufacturer, along with additional codes used for traceability. Many pieces also show an AS classification (often AS1, AS2, or AS3) that reflects glazing category and typical placement based on light transmission, and the etching may indicate tempered versus laminated construction. Some roof panels also carry international marks such as ECE R43 when produced for multiple markets. You may see an “M” number or internal variant code that differentiates tint shade, thickness, or coatings—helpful for matching like-for-like features on your Subaru Exiga Crossover 7. The goal is simple: confirm the replacement roof glass is clearly marked, readable, and consistent with the original glass type and features. Missing or suspicious markings are a red flag for compliance and reliability in sunroof glass replacement, moonroof glass replacement, and panoramic roof glass replacement. Bang AutoGlass can confirm the markings and complete mobile roof glass replacement as soon as next day.
Order-Ready Checklist: Frame, Seals, Deflector, and Hardware Notes That Prevent Reorders
To avoid a reorder on a Subaru Exiga Crossover 7 roof glass replacement, treat the roof as a system—not just a panel. Start by confirming whether you need glass-only or a full assembly/cassette. On many roofs, the glass bolts to hinge blocks, lift arms, and mounting brackets; if any are bent, cracked, or missing, even the correct glass can sit high, bind, or leak. If you’re reusing hardware, photograph and mark hinge-block positions and adjustment points so the new panel returns to the same alignment references. Next, inspect perimeter seals and secondary gaskets for tears, flattening, or shrinkage, since worn seals are a top cause of wind noise and water intrusion. Check the wind deflector (arms, clips, springs) and verify drains are clear. Finally, confirm the “small parts” that derail installs: correct fasteners, intact guide shoes, undamaged trim rings, and matching tabs. Note any prior aftermarket modifications or evidence of previous adhesive work so installation planning is realistic. For end-to-end verification, Bang AutoGlass can confirm the right parts and perform mobile service as soon as next day. Most replacements take 30–45 minutes; allow at least one hour of cure time before drive-away. Every job is backed by our lifetime workmanship warranty.
Services
Service Areas
Sunroof vs Moonroof on Subaru Exiga Crossover 7: How to Order the Correct Roof Glass Replacement
Sunroof vs Moonroof on Subaru Exiga Crossover 7: Terminology vs Actual Roof Design
When people search sunroof vs moonroof for a Subaru Exiga Crossover 7, they want a definition, but the right roof glass replacement depends on the roof design, not the name. Older usage called an opaque tilting or sliding panel a sunroof and a tinted glass panel with a sunshade a moonroof, yet many OEMs now use the terms interchangeably. For correct sunroof glass replacement or moonroof glass replacement, confirm what you have: fixed roof glass vs an operable panel, vent only vs vent and slide, slides above the roof spoiler style vs retracts into the roof pocket, and single panel vs panoramic roof glass with multiple panels. These details determine curvature, mounting tabs, track interface, seals, and flush fit. Bang AutoGlass verifies fitment before ordering. If you are unsure, take photos outside and inside with the roof closed, vented, and open, and note how the panel travels. We can confirm the correct roof glass for your Subaru Exiga Crossover 7 and schedule mobile replacement as soon as next day. Most installs take 30-45 minutes; allow at least one hour of cure time before safe drive away. Every job includes a lifetime workmanship warranty.
Identify Your Roof Type Before Ordering: Pop-Up, Tilt/Slide, and Panoramic on Subaru Exiga Crossover 7
Before ordering roof glass replacement for a Subaru Exiga Crossover 7, identify the roof type by how the panel opens and where it stores, because sunroof glass is not one size fits all. Pop up roofs are simplest: the panel tilts for ventilation, is often manual, and uses basic hinge or latch hardware. Tilt and slide spoiler roofs vent first, then slide rearward above the roof skin; the glass stays visible and you usually see side rails. In built sliding roofs also vent, but then retract into a pocket between the roof and headliner, changing the glass edge and attachment points. Panoramic roofs add complexity with multiple panels, larger frames, and specific drain routing, often a fixed rear section plus a movable front section. Also confirm factory vs aftermarket. Aftermarket roofs often show a trim ring and raised cutout lip, while factory systems sit more flush and rely on OEM specific tabs. Checklist for your Subaru Exiga Crossover 7: watch the first motion, count panels, note manual vs powered shade, and photograph the tracks, wind deflector area, and perimeter seal. Bang AutoGlass can verify fitment and handle mobile sunroof glass replacement, moonroof glass replacement, or panoramic roof glass replacement as soon as next day.
Get the Right Part Number: VIN, Trim Level, Model Year, and Build Variations for Subaru Exiga Crossover 7
Ordering roof glass replacement for a Subaru Exiga Crossover 7 is a part number exercise, and the correct option can vary even within the same model year. Begin with the VIN, because glass databases use it to confirm generation, submodel, and option codes that are easy to miss online. Then confirm trim and roof package: fixed glass, power tilt and slide, and panoramic multi panel assemblies are usually separate listings. Next, look for production breaks. Check the driver door jamb build date and compare it to catalog notes that specify from and to ranges or VIN serial breakpoints. Mid year plant or supplier changes can alter curvature, thickness, or mounting tab layout, so two same year Subaru Exiga Crossover 7 vehicles can legitimately use different sunroof glass or moonroof glass. A final cross check is visual: photograph the glass edge, tabs, and the track interface, and note whether the panel slides above the roof or retracts inward. If you want an end to end solution, Bang AutoGlass can verify fitment, source the correct part, and perform mobile replacement as soon as next day. Most installs take 30-45 minutes; allow one hour cure time before safe drive away. Every job is backed by a lifetime workmanship warranty.
Match the Glass Features: Tint/Privacy Shade, Coatings, and Factory Options on Subaru Exiga Crossover 7
Choosing roof glass for a Subaru Exiga Crossover 7 isn’t only about calling it a sunroof or moonroof; it’s about ordering the exact factory configuration. Start with the obvious: tint level and whether the interior shade is manual or powered, because shade tracks and clearances vary by package. Then confirm solar-control technology. Many roof panels are laminated with UV- and IR-filtering interlayers, and those layers can affect color, gloss, and reflectivity. Next, match the edge treatment. The black frit border and dot-matrix are baked-on ceramic layers that shield the urethane bond and seals from UV and create a stable bonding surface, so the frit placement and edge profile should mirror your original Subaru Exiga Crossover 7 glass. Also verify tempered versus laminated construction and thickness; some laminated panels include acoustic layers to cut wind noise. Finally, account for options that drive different parts: panoramic multi-panel systems, integrated shade rails, sensors or antenna provisions on certain trims, and roof curvature differences across builds. Getting tint, coatings, frit pattern, and construction right helps you avoid common fitment and appearance issues in sunroof glass replacement and panoramic roof glass replacement. Bang AutoGlass can confirm the specs and complete mobile roof glass installation as soon as next day.
Verify Safety Markings: DOT Symbol, Manufacturer Code, and FMVSS 205 Compliance
Before installing roof glass on a Subaru Exiga Crossover 7, verify the permanent safety markings. In the U.S., FMVSS 205 (49 CFR 571.205) governs automotive glazing and incorporates labeling requirements through ANSI/SAE Z26.1, so reputable replacement roof glass will have an etched manufacturer “bug,” not just a sticker. Look for the DOT code (DOT plus a number) that identifies the glazing manufacturer, along with additional codes used for traceability. Many pieces also show an AS classification (often AS1, AS2, or AS3) that reflects glazing category and typical placement based on light transmission, and the etching may indicate tempered versus laminated construction. Some roof panels also carry international marks such as ECE R43 when produced for multiple markets. You may see an “M” number or internal variant code that differentiates tint shade, thickness, or coatings—helpful for matching like-for-like features on your Subaru Exiga Crossover 7. The goal is simple: confirm the replacement roof glass is clearly marked, readable, and consistent with the original glass type and features. Missing or suspicious markings are a red flag for compliance and reliability in sunroof glass replacement, moonroof glass replacement, and panoramic roof glass replacement. Bang AutoGlass can confirm the markings and complete mobile roof glass replacement as soon as next day.
Order-Ready Checklist: Frame, Seals, Deflector, and Hardware Notes That Prevent Reorders
To avoid a reorder on a Subaru Exiga Crossover 7 roof glass replacement, treat the roof as a system—not just a panel. Start by confirming whether you need glass-only or a full assembly/cassette. On many roofs, the glass bolts to hinge blocks, lift arms, and mounting brackets; if any are bent, cracked, or missing, even the correct glass can sit high, bind, or leak. If you’re reusing hardware, photograph and mark hinge-block positions and adjustment points so the new panel returns to the same alignment references. Next, inspect perimeter seals and secondary gaskets for tears, flattening, or shrinkage, since worn seals are a top cause of wind noise and water intrusion. Check the wind deflector (arms, clips, springs) and verify drains are clear. Finally, confirm the “small parts” that derail installs: correct fasteners, intact guide shoes, undamaged trim rings, and matching tabs. Note any prior aftermarket modifications or evidence of previous adhesive work so installation planning is realistic. For end-to-end verification, Bang AutoGlass can confirm the right parts and perform mobile service as soon as next day. Most replacements take 30–45 minutes; allow at least one hour of cure time before drive-away. Every job is backed by our lifetime workmanship warranty.
Enjoy More Relevant Blogs
After Breakage: Subaru Exiga Crossover 7 Sunroof Glass Replacement Cleanup, Weather Protection, and Next Steps
After breakage on a Subaru Exiga Crossover 7 sunroof, follow safe cleanup steps, protect the interior from weather, and know what to expect with replacement next.
Sunroof Leak on Subaru Exiga Crossover 7: Drain Fix vs Sunroof Glass Replacement Decision Guide
Sunroof leak on Subaru Exiga Crossover 7? Compare drain fixes vs sunroof glass replacement, warning signs, and the best next step to stop water damage fast today.
Urethane Bonding for Subaru Exiga Crossover 7 Sunroof Glass Replacement: Why Adhesive Quality Matters
Urethane bonding for Subaru Exiga Crossover 7 sunroof glass replacement: why adhesive quality matters for safety, leaks, and long-term durability after install.
Will My Comprehensive Policy Cover Subaru Exiga Crossover 7 Sunroof Glass Replacement? Claim Steps, Photos to Take, and Deductible Basics
Will comprehensive insurance cover Subaru Exiga Crossover 7 sunroof glass replacement? See claim steps, photos to take, deductible basics, and tips before filing.
How Much Does Subaru Exiga Crossover 7 Sunroof Glass Replacement Cost? OEM vs Aftermarket, Labor Factors, and Estimate Tips
Subaru Exiga Crossover 7 sunroof glass replacement cost: price drivers, OEM vs aftermarket options, labor factors, and tips for an accurate estimate—compare now.
Panoramic Sunroof Glass Replacement for Subaru Exiga Crossover 7: Install Steps and Safe Drive-Away Timing
Panoramic sunroof glass replacement for Subaru Exiga Crossover 7: walk through install steps, cure-time rules, and safe drive-away timing so you avoid leaks. Book now.
OEM-Quality Sunroof Glass Replacement for Subaru Exiga Crossover 7: DOT Markings and FMVSS 205 Explained
OEM-quality sunroof glass replacement for Subaru Exiga Crossover 7: understand DOT markings and FMVSS 205, plus fit checks that help prevent leaks—get it done right.
How to Schedule Mobile Sunroof Glass Replacement for Subaru Exiga Crossover 7
Schedule mobile sunroof glass replacement for Subaru Exiga Crossover 7: what info to share, photos to take, timing, and what to expect on-site—avoid delays today.
Wind Noise After Sunroof Glass Replacement on Subaru Exiga Crossover 7: Seal, Fit, and Alignment Checklist
Wind noise after Subaru Exiga Crossover 7 sunroof glass replacement? Check seal fit, alignment, and hardware so the roof closes tight and stays quiet at speed daily.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm