Services
Service Areas
Cleanup After Quarter Window Breakage on Toyota C-Hr: Safe Glass Removal and Interior Protection
With a broken quarter window on your Toyota C-Hr, cleanup is where small mistakes turn into scratches, lingering glass, and drafts from a rushed cover. Because quarter glass is tempered, it breaks into pellets that migrate into carpet, seat rails, and storage pockets. Secure the vehicle first: keep children and pets away, wear eye protection and cut-resistant gloves, and remove loose items that can hide shards. Lift the largest pieces from the opening and lower ledge rather than pressing down. Scoop with a dustpan or stiff cardboard, then vacuum in passes with a hose and crevice tool, starting at trim seams and working down through seats, carpet, and floor mats. Skip aggressive sweeping; it drives fine glass deeper into fabric. For upholstery, press wide painter’s tape or use a lint roller to capture the grit you can’t see, and wipe hard plastics with a damp microfiber. If you need a short-term weather shield, tape plastic sheeting from the inside with painter’s tape so it sheds rain without pulling paint or leaving residue. Then schedule Bang AutoGlass for mobile quarter window replacement—we arrive with the correct glass, complete final cleanup, and often restore your Toyota C-Hr as soon as next day.
Verify the Correct Quarter Glass for Toyota C-Hr: Fixed vs Pop-Out, Tint Match, and DOT Markings
Before installing a new quarter window on your Toyota C-Hr, we verify exact fitment, because an “almost right” piece can cause leaks, wind noise, trim gaps, or a tint mismatch that’s obvious in daylight. First we confirm the quarter glass style: fixed glass bonded with urethane versus a pop-out/vent unit with hinges or latches. We match your Toyota C-Hr body style, model-year range, and left/right orientation. Next we align appearance and solar performance—clear versus factory privacy tint, shade consistency, and how any existing window film will blend so the replacement doesn’t stand out. We also check the glass “bug” markings: DOT codes, safety identifiers, manufacturer traceability, and the correct AS rating for non-windshield glazing. Many quarter windows arrive as an encapsulated assembly with pre-attached molding, studs, locator pins, or clips; those details control seating depth, reveal lines, and how interior panels lock back in. When applicable, we confirm embedded features such as antenna elements. The result is an OEM-correct Toyota C-Hr quarter window replacement that seals properly. If comprehensive insurance applies, Bang AutoGlass works with all insurance companies and can help you complete the claim steps on-site.
Remove Trim and Old Glass: Toyota C-Hr Quarter Window Replacement Disassembly Checklist
Quarter window replacement on a Toyota C-Hr depends on controlled access: remove only what’s necessary, protect painted edges, and keep clips intact so the car goes back together without rattles. We start by stabilizing the work area—powering down accessories, opening another door or window to reduce pressure changes, and masking adjacent paint, weatherstrips, and trim. From inside the vehicle, we move the minimum panels needed (often a rear seat bolster, quarter trim, and cargo-side panels), using non-marring tools and organizing hardware so every fastener returns to its original location. We work carefully around seatbelt anchors and curtain airbag zones to avoid damage and warning lights. Release method depends on the Toyota C-Hr design: bonded glass is separated by cutting the urethane bead cleanly without gouging the pinchweld or bending the flange; bolt-in or framed styles require supporting the glass as retainers are removed to prevent a sudden drop. After removal, we re-vacuum the cavity, address any damaged molding, and prep the opening for installation. Most mobile replacements take about 30–45 minutes for the swap, followed by adhesive cure time before safe drive-away.
Prep the Pinchweld and Bond Area: Corrosion Checks, Primers, and Adhesion Readiness
A clean, long-lasting quarter window replacement on your Toyota C-Hr starts with bond prep, not the new glass. For bonded quarter glass, the pinchweld (the metal flange around the opening) and the glass bond band must be stable and clean so urethane can fully adhere. At Bang AutoGlass, we begin with a corrosion and coating check for rust, bubbling paint, exposed metal, and prior repair residue that can weaken the seal and cause leaks. We preserve factory E-coat and sound paint whenever possible, then trim the old urethane down to a thin, uniform base layer so fresh urethane can bond to a consistent substrate. If any bare metal is exposed from corrosion cleanup or a cutting nick, we treat it with the correct refinish/body primer per adhesive and refinish guidance, and apply pinchweld primer when the urethane system requires it. On the glass side, we clean the bond area and use the appropriate activator or glass/frit primer as specified to promote adhesion and UV protection at the bond line. Contamination control is strict: no silicone products, no oily fingerprints, and no skipped flash times. We dry-fit the quarter glass to confirm alignment, reveal, and trim engagement, then mask adjacent paint for a crisp finished edge. This prep prevents water intrusion and supports an OEM-style seal—often completed at your location by our mobile auto glass team.
Urethane Bonding and Minimum Drive-Away Time for Toyota C-Hr: SDAT Factors You Must Follow
Bonding is where a Toyota C-Hr quarter window replacement becomes either a quiet, watertight repair or a repeat leak and wind-noise complaint. Bang AutoGlass uses automotive-grade urethane and applies a continuous, properly sized bead to maintain correct stand-off, seat depth, and molding support. We pay special attention to corners and transitions, where gaps or thin spots can become water paths. After the bead is laid, the quarter glass is set on its locators, aligned to body lines, and pressed evenly to achieve full contact without collapsing the bead. We then secure and re-check flushness so the glass cannot shift while curing begins. Safe Drive-Away Time (SDAT) is required guidance and varies by urethane formula plus ambient temperature and relative humidity. Cooler and drier conditions generally slow cure, while warmer and more humid conditions typically accelerate it, which is why professional systems publish SDAT charts and procedures. As a practical baseline, we require at least one full hour before your Toyota C-Hr is considered safe to drive, even when the install itself commonly takes about 30–45 minutes. During early cure, avoid door slams, aggressive window operation, or rough roads that flex the opening. For best results, postpone high-pressure washing for 24–48 hours and keep the bond line clean and undisturbed. Our mobile auto glass team can complete the job at your location, and we work with all insurance companies when comprehensive coverage applies.
Final Quality Checks: Leak Test, Wind Noise, Trim Fit, and Documentation for Toyota C-Hr
Before your Toyota C-Hr leaves our care, we run a structured quality-control sequence so the quarter window replacement performs as intended. First, we verify fit and appearance: the glass should be centered, reveal lines should mirror the opposite side, and any molding or encapsulation must sit flush with no lifted corners, gaps, or uneven edges. We check for proper urethane contact and ensure there is no contamination or excessive squeeze-out that could interfere with trim seating. Next, we reassemble interior panels and confirm clip engagement to prevent future buzzes, rattles, or loose trim in the quarter and cargo area. Leak prevention is validated with a controlled water test along the perimeter while we observe inside for intrusion into the quarter cavity or cargo area. If wind noise is a concern, we evaluate sealing consistency and trim contact, since small edge gaps can be audible at highway speed. We then clean the glass and ensure surrounding paint and trim are returned clean and residue-free. Finally, we document the job details—part verification, DOT markings, and install notes—and review aftercare: honoring the minimum one-hour safe drive-away time, avoiding door slams during early cure, and postponing high-pressure washes for 24–48 hours. Your paperwork also reflects our lifetime workmanship warranty for peace of mind. If you are processing an insurance claim, we can assist with any insurer as long as comprehensive coverage applies. The outcome is a Toyota C-Hr quarter window replacement that looks right, seals right, and is supported with clear documentation.
Services
Service Areas
Cleanup After Quarter Window Breakage on Toyota C-Hr: Safe Glass Removal and Interior Protection
With a broken quarter window on your Toyota C-Hr, cleanup is where small mistakes turn into scratches, lingering glass, and drafts from a rushed cover. Because quarter glass is tempered, it breaks into pellets that migrate into carpet, seat rails, and storage pockets. Secure the vehicle first: keep children and pets away, wear eye protection and cut-resistant gloves, and remove loose items that can hide shards. Lift the largest pieces from the opening and lower ledge rather than pressing down. Scoop with a dustpan or stiff cardboard, then vacuum in passes with a hose and crevice tool, starting at trim seams and working down through seats, carpet, and floor mats. Skip aggressive sweeping; it drives fine glass deeper into fabric. For upholstery, press wide painter’s tape or use a lint roller to capture the grit you can’t see, and wipe hard plastics with a damp microfiber. If you need a short-term weather shield, tape plastic sheeting from the inside with painter’s tape so it sheds rain without pulling paint or leaving residue. Then schedule Bang AutoGlass for mobile quarter window replacement—we arrive with the correct glass, complete final cleanup, and often restore your Toyota C-Hr as soon as next day.
Verify the Correct Quarter Glass for Toyota C-Hr: Fixed vs Pop-Out, Tint Match, and DOT Markings
Before installing a new quarter window on your Toyota C-Hr, we verify exact fitment, because an “almost right” piece can cause leaks, wind noise, trim gaps, or a tint mismatch that’s obvious in daylight. First we confirm the quarter glass style: fixed glass bonded with urethane versus a pop-out/vent unit with hinges or latches. We match your Toyota C-Hr body style, model-year range, and left/right orientation. Next we align appearance and solar performance—clear versus factory privacy tint, shade consistency, and how any existing window film will blend so the replacement doesn’t stand out. We also check the glass “bug” markings: DOT codes, safety identifiers, manufacturer traceability, and the correct AS rating for non-windshield glazing. Many quarter windows arrive as an encapsulated assembly with pre-attached molding, studs, locator pins, or clips; those details control seating depth, reveal lines, and how interior panels lock back in. When applicable, we confirm embedded features such as antenna elements. The result is an OEM-correct Toyota C-Hr quarter window replacement that seals properly. If comprehensive insurance applies, Bang AutoGlass works with all insurance companies and can help you complete the claim steps on-site.
Remove Trim and Old Glass: Toyota C-Hr Quarter Window Replacement Disassembly Checklist
Quarter window replacement on a Toyota C-Hr depends on controlled access: remove only what’s necessary, protect painted edges, and keep clips intact so the car goes back together without rattles. We start by stabilizing the work area—powering down accessories, opening another door or window to reduce pressure changes, and masking adjacent paint, weatherstrips, and trim. From inside the vehicle, we move the minimum panels needed (often a rear seat bolster, quarter trim, and cargo-side panels), using non-marring tools and organizing hardware so every fastener returns to its original location. We work carefully around seatbelt anchors and curtain airbag zones to avoid damage and warning lights. Release method depends on the Toyota C-Hr design: bonded glass is separated by cutting the urethane bead cleanly without gouging the pinchweld or bending the flange; bolt-in or framed styles require supporting the glass as retainers are removed to prevent a sudden drop. After removal, we re-vacuum the cavity, address any damaged molding, and prep the opening for installation. Most mobile replacements take about 30–45 minutes for the swap, followed by adhesive cure time before safe drive-away.
Prep the Pinchweld and Bond Area: Corrosion Checks, Primers, and Adhesion Readiness
A clean, long-lasting quarter window replacement on your Toyota C-Hr starts with bond prep, not the new glass. For bonded quarter glass, the pinchweld (the metal flange around the opening) and the glass bond band must be stable and clean so urethane can fully adhere. At Bang AutoGlass, we begin with a corrosion and coating check for rust, bubbling paint, exposed metal, and prior repair residue that can weaken the seal and cause leaks. We preserve factory E-coat and sound paint whenever possible, then trim the old urethane down to a thin, uniform base layer so fresh urethane can bond to a consistent substrate. If any bare metal is exposed from corrosion cleanup or a cutting nick, we treat it with the correct refinish/body primer per adhesive and refinish guidance, and apply pinchweld primer when the urethane system requires it. On the glass side, we clean the bond area and use the appropriate activator or glass/frit primer as specified to promote adhesion and UV protection at the bond line. Contamination control is strict: no silicone products, no oily fingerprints, and no skipped flash times. We dry-fit the quarter glass to confirm alignment, reveal, and trim engagement, then mask adjacent paint for a crisp finished edge. This prep prevents water intrusion and supports an OEM-style seal—often completed at your location by our mobile auto glass team.
Urethane Bonding and Minimum Drive-Away Time for Toyota C-Hr: SDAT Factors You Must Follow
Bonding is where a Toyota C-Hr quarter window replacement becomes either a quiet, watertight repair or a repeat leak and wind-noise complaint. Bang AutoGlass uses automotive-grade urethane and applies a continuous, properly sized bead to maintain correct stand-off, seat depth, and molding support. We pay special attention to corners and transitions, where gaps or thin spots can become water paths. After the bead is laid, the quarter glass is set on its locators, aligned to body lines, and pressed evenly to achieve full contact without collapsing the bead. We then secure and re-check flushness so the glass cannot shift while curing begins. Safe Drive-Away Time (SDAT) is required guidance and varies by urethane formula plus ambient temperature and relative humidity. Cooler and drier conditions generally slow cure, while warmer and more humid conditions typically accelerate it, which is why professional systems publish SDAT charts and procedures. As a practical baseline, we require at least one full hour before your Toyota C-Hr is considered safe to drive, even when the install itself commonly takes about 30–45 minutes. During early cure, avoid door slams, aggressive window operation, or rough roads that flex the opening. For best results, postpone high-pressure washing for 24–48 hours and keep the bond line clean and undisturbed. Our mobile auto glass team can complete the job at your location, and we work with all insurance companies when comprehensive coverage applies.
Final Quality Checks: Leak Test, Wind Noise, Trim Fit, and Documentation for Toyota C-Hr
Before your Toyota C-Hr leaves our care, we run a structured quality-control sequence so the quarter window replacement performs as intended. First, we verify fit and appearance: the glass should be centered, reveal lines should mirror the opposite side, and any molding or encapsulation must sit flush with no lifted corners, gaps, or uneven edges. We check for proper urethane contact and ensure there is no contamination or excessive squeeze-out that could interfere with trim seating. Next, we reassemble interior panels and confirm clip engagement to prevent future buzzes, rattles, or loose trim in the quarter and cargo area. Leak prevention is validated with a controlled water test along the perimeter while we observe inside for intrusion into the quarter cavity or cargo area. If wind noise is a concern, we evaluate sealing consistency and trim contact, since small edge gaps can be audible at highway speed. We then clean the glass and ensure surrounding paint and trim are returned clean and residue-free. Finally, we document the job details—part verification, DOT markings, and install notes—and review aftercare: honoring the minimum one-hour safe drive-away time, avoiding door slams during early cure, and postponing high-pressure washes for 24–48 hours. Your paperwork also reflects our lifetime workmanship warranty for peace of mind. If you are processing an insurance claim, we can assist with any insurer as long as comprehensive coverage applies. The outcome is a Toyota C-Hr quarter window replacement that looks right, seals right, and is supported with clear documentation.
Services
Service Areas
Cleanup After Quarter Window Breakage on Toyota C-Hr: Safe Glass Removal and Interior Protection
With a broken quarter window on your Toyota C-Hr, cleanup is where small mistakes turn into scratches, lingering glass, and drafts from a rushed cover. Because quarter glass is tempered, it breaks into pellets that migrate into carpet, seat rails, and storage pockets. Secure the vehicle first: keep children and pets away, wear eye protection and cut-resistant gloves, and remove loose items that can hide shards. Lift the largest pieces from the opening and lower ledge rather than pressing down. Scoop with a dustpan or stiff cardboard, then vacuum in passes with a hose and crevice tool, starting at trim seams and working down through seats, carpet, and floor mats. Skip aggressive sweeping; it drives fine glass deeper into fabric. For upholstery, press wide painter’s tape or use a lint roller to capture the grit you can’t see, and wipe hard plastics with a damp microfiber. If you need a short-term weather shield, tape plastic sheeting from the inside with painter’s tape so it sheds rain without pulling paint or leaving residue. Then schedule Bang AutoGlass for mobile quarter window replacement—we arrive with the correct glass, complete final cleanup, and often restore your Toyota C-Hr as soon as next day.
Verify the Correct Quarter Glass for Toyota C-Hr: Fixed vs Pop-Out, Tint Match, and DOT Markings
Before installing a new quarter window on your Toyota C-Hr, we verify exact fitment, because an “almost right” piece can cause leaks, wind noise, trim gaps, or a tint mismatch that’s obvious in daylight. First we confirm the quarter glass style: fixed glass bonded with urethane versus a pop-out/vent unit with hinges or latches. We match your Toyota C-Hr body style, model-year range, and left/right orientation. Next we align appearance and solar performance—clear versus factory privacy tint, shade consistency, and how any existing window film will blend so the replacement doesn’t stand out. We also check the glass “bug” markings: DOT codes, safety identifiers, manufacturer traceability, and the correct AS rating for non-windshield glazing. Many quarter windows arrive as an encapsulated assembly with pre-attached molding, studs, locator pins, or clips; those details control seating depth, reveal lines, and how interior panels lock back in. When applicable, we confirm embedded features such as antenna elements. The result is an OEM-correct Toyota C-Hr quarter window replacement that seals properly. If comprehensive insurance applies, Bang AutoGlass works with all insurance companies and can help you complete the claim steps on-site.
Remove Trim and Old Glass: Toyota C-Hr Quarter Window Replacement Disassembly Checklist
Quarter window replacement on a Toyota C-Hr depends on controlled access: remove only what’s necessary, protect painted edges, and keep clips intact so the car goes back together without rattles. We start by stabilizing the work area—powering down accessories, opening another door or window to reduce pressure changes, and masking adjacent paint, weatherstrips, and trim. From inside the vehicle, we move the minimum panels needed (often a rear seat bolster, quarter trim, and cargo-side panels), using non-marring tools and organizing hardware so every fastener returns to its original location. We work carefully around seatbelt anchors and curtain airbag zones to avoid damage and warning lights. Release method depends on the Toyota C-Hr design: bonded glass is separated by cutting the urethane bead cleanly without gouging the pinchweld or bending the flange; bolt-in or framed styles require supporting the glass as retainers are removed to prevent a sudden drop. After removal, we re-vacuum the cavity, address any damaged molding, and prep the opening for installation. Most mobile replacements take about 30–45 minutes for the swap, followed by adhesive cure time before safe drive-away.
Prep the Pinchweld and Bond Area: Corrosion Checks, Primers, and Adhesion Readiness
A clean, long-lasting quarter window replacement on your Toyota C-Hr starts with bond prep, not the new glass. For bonded quarter glass, the pinchweld (the metal flange around the opening) and the glass bond band must be stable and clean so urethane can fully adhere. At Bang AutoGlass, we begin with a corrosion and coating check for rust, bubbling paint, exposed metal, and prior repair residue that can weaken the seal and cause leaks. We preserve factory E-coat and sound paint whenever possible, then trim the old urethane down to a thin, uniform base layer so fresh urethane can bond to a consistent substrate. If any bare metal is exposed from corrosion cleanup or a cutting nick, we treat it with the correct refinish/body primer per adhesive and refinish guidance, and apply pinchweld primer when the urethane system requires it. On the glass side, we clean the bond area and use the appropriate activator or glass/frit primer as specified to promote adhesion and UV protection at the bond line. Contamination control is strict: no silicone products, no oily fingerprints, and no skipped flash times. We dry-fit the quarter glass to confirm alignment, reveal, and trim engagement, then mask adjacent paint for a crisp finished edge. This prep prevents water intrusion and supports an OEM-style seal—often completed at your location by our mobile auto glass team.
Urethane Bonding and Minimum Drive-Away Time for Toyota C-Hr: SDAT Factors You Must Follow
Bonding is where a Toyota C-Hr quarter window replacement becomes either a quiet, watertight repair or a repeat leak and wind-noise complaint. Bang AutoGlass uses automotive-grade urethane and applies a continuous, properly sized bead to maintain correct stand-off, seat depth, and molding support. We pay special attention to corners and transitions, where gaps or thin spots can become water paths. After the bead is laid, the quarter glass is set on its locators, aligned to body lines, and pressed evenly to achieve full contact without collapsing the bead. We then secure and re-check flushness so the glass cannot shift while curing begins. Safe Drive-Away Time (SDAT) is required guidance and varies by urethane formula plus ambient temperature and relative humidity. Cooler and drier conditions generally slow cure, while warmer and more humid conditions typically accelerate it, which is why professional systems publish SDAT charts and procedures. As a practical baseline, we require at least one full hour before your Toyota C-Hr is considered safe to drive, even when the install itself commonly takes about 30–45 minutes. During early cure, avoid door slams, aggressive window operation, or rough roads that flex the opening. For best results, postpone high-pressure washing for 24–48 hours and keep the bond line clean and undisturbed. Our mobile auto glass team can complete the job at your location, and we work with all insurance companies when comprehensive coverage applies.
Final Quality Checks: Leak Test, Wind Noise, Trim Fit, and Documentation for Toyota C-Hr
Before your Toyota C-Hr leaves our care, we run a structured quality-control sequence so the quarter window replacement performs as intended. First, we verify fit and appearance: the glass should be centered, reveal lines should mirror the opposite side, and any molding or encapsulation must sit flush with no lifted corners, gaps, or uneven edges. We check for proper urethane contact and ensure there is no contamination or excessive squeeze-out that could interfere with trim seating. Next, we reassemble interior panels and confirm clip engagement to prevent future buzzes, rattles, or loose trim in the quarter and cargo area. Leak prevention is validated with a controlled water test along the perimeter while we observe inside for intrusion into the quarter cavity or cargo area. If wind noise is a concern, we evaluate sealing consistency and trim contact, since small edge gaps can be audible at highway speed. We then clean the glass and ensure surrounding paint and trim are returned clean and residue-free. Finally, we document the job details—part verification, DOT markings, and install notes—and review aftercare: honoring the minimum one-hour safe drive-away time, avoiding door slams during early cure, and postponing high-pressure washes for 24–48 hours. Your paperwork also reflects our lifetime workmanship warranty for peace of mind. If you are processing an insurance claim, we can assist with any insurer as long as comprehensive coverage applies. The outcome is a Toyota C-Hr quarter window replacement that looks right, seals right, and is supported with clear documentation.
Enjoy More Relevant Blogs
Safety Standards Explained: DOT Markings and FMVSS 205 for Toyota C-Hr Quarter Glass Replacement
DOT markings and FMVSS 205 explained for Toyota C-Hr quarter glass replacement—how to verify safety markings and choose compliant OEM-quality glass.
How Long After Toyota C-Hr Quarter Panel Glass Replacement Can You Drive or Wash the Car? Urethane Cure-Time Rules
After Toyota C-Hr quarter panel glass replacement, learn safe drive-away time, when to wash, and urethane cure rules that help prevent leaks and wind noise.
How Much Does Toyota C-Hr Quarter Panel Glass Replacement Cost? Insurance Deductibles, Estimates, and Ways to Save
Cost to replace Toyota C-Hr quarter panel glass: key price factors, OEM vs aftermarket options, insurance deductibles, estimates, and smart ways to save.
OEM-Quality Quarter Glass Replacement for Toyota C-Hr: Fit, Trim, and Weather-Seal Checklist
OEM-quality quarter glass replacement for Toyota C-Hr: fit, trim, and weather-seal checklist for correct install, leak prevention, and clean finish.
After a Break-In: Toyota C-Hr Quarter Glass Replacement Plan to Restore Security and Visibility
After a break-in on Toyota C-Hr, restore security with a quarter glass replacement plan: cleanup, temporary protection, scheduling, and post-install checks.
Tint & Privacy Glass Match Guide: Toyota C-Hr Quarter Glass Replacement Done Right
Tint and privacy match guide for Toyota C-Hr quarter glass replacement—how to match shade, markings, and fit so the new glass looks factory-perfect.
Stop Leaks and Wind Noise: What Proper Toyota C-Hr Quarter Glass Replacement Should Prevent
Stop leaks and wind noise with proper Toyota C-Hr quarter glass replacement. Learn what correct fit, sealing, and trim should prevent after install.
How to Schedule Mobile Quarter Glass Replacement for Toyota C-Hr
Need mobile quarter glass replacement for Toyota C-Hr? Follow our scheduling checklist, photos to take, timing, and on-site tips to restore security.
Fixed Quarter Window vs Vent Glass on Toyota C-Hr: Ordering the Correct Replacement
Fixed quarter window vs vent glass on Toyota C-Hr: how to identify yours and order the correct replacement for fit, sealing, and safety—read this now.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm