Services
Service Areas
ADAS Warning Lights on Toyota Fortuner: What the Icons and Messages Commonly Indicate
ADAS warning lights on your Toyota Fortuner mean a driver-assist feature is limited, temporarily disabled, or needs service. The icon often indicates the system: a car between lane lines is Lane Keep Assist/Lane Departure Warning, an “impact” symbol points to Forward Collision Warning or Automatic Emergency Braking, and a speedometer/cruise icon commonly relates to Adaptive Cruise Control. Messages such as “Driver Assist Limited,” “Camera Obscured,” “Front Radar Blocked,” or “ACC Unavailable” usually mean a sensor cannot see clearly enough or the system failed a self-check. Start with the basics. Clean the windshield around the forward camera near the rearview mirror (inside and out), clear frost or fog, and confirm wipers and washer fluid work without streaks. Up front, wipe the radar cover or emblem area and remove bugs, mud, or snow. If the warning started after a rock chip, crack, windshield replacement, or a minor front-end tap, the camera bracket or sensor alignment may be out of tolerance and calibration may be required. Bang AutoGlass offers mobile windshield replacement as soon as next day. Most installs take 30–45 minutes, plus at least 1 hour of safe drive-away time, with a lifetime workmanship warranty and insurance help.
When Calibration Is the Fix for Toyota Fortuner: Post-Windshield Replacement and Sensor Alignment Triggers
For many Toyota Fortuner drivers, calibration is the right fix when ADAS warnings appear after a windshield replacement or any repair that disturbs the forward camera or radar. These systems rely on tight tolerances: the camera bracket angle, windshield specification, and software must agree on what “straight ahead” looks like. OEM procedures commonly call for a learn/calibration whenever the windshield is replaced, a camera or radar is removed/reinstalled, or front-end repairs change sensor position. Calibration is also triggered by vehicle-geometry changes—bumper removal, collision repair, wheel alignment, suspension or ride-height work, steering angle sensor resets, or non-OEM tire sizing. If the vehicle’s “aim” changes, ADAS can disable Lane Keep Assist, Adaptive Cruise Control, and Automatic Emergency Braking until targets are re-established. Best practice is a repeatable workflow: verify the correct windshield for the Toyota Fortuner, confirm the camera mount is clean and secure, run a diagnostic pre-scan, complete OEM static targets and/or dynamic road learning, then perform a post-scan to ensure no codes return. Bang AutoGlass provides mobile windshield replacement as soon as next day (30–45 minutes plus at least 1 hour safe drive-away time) and a lifetime workmanship warranty; we can help coordinate calibration if needed.
When It’s Not Calibration on Toyota Fortuner: Obstructions, Damage, Voltage, Wiring, and Module Faults
On a Toyota Fortuner, an ADAS warning light does not automatically mean calibration is needed. Many systems pause whenever sensor input is unreliable. Weather and road conditions are common causes: heavy rain, snow, fog, glare, or road spray can reduce camera contrast and prevent tracking of lane markings or vehicles, leading to “Camera Obscured” or “Driver Assist Limited.” Features often return once visibility improves. Obstructions and add-ons can create the same symptoms. Dashcams, toll tags, stickers, and poorly placed tint near the camera window can block the forward view. Up front, a cracked, misaligned, or painted radar cover/emblem can interrupt the signal and trigger “Front Radar Blocked” or “ACC Unavailable.” Electrical stability matters, too: a weak 12-volt battery or recent battery disconnect can set low-voltage or communication faults that take modules offline. If warnings persist after cleaning, treat it as diagnostics. A DTC scan helps distinguish a blocked sensor from fuse, ground, connector, corrosion, harness, camera/radar unit, or software issues. If the warning began after windshield damage, replacement, or a front-end impact, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Toyota Fortuner: Reading DTCs, Root-Cause Checks, and OEM Procedures
On a modern Toyota Fortuner, clearing ADAS warning lights starts with scan data, not parts swapping. The dash icon only tells you a system is limited; it does not identify the trigger. Many OEM procedures call for a pre-repair health scan whenever the windshield camera, front radar, ABS/steering inputs, or related wiring has been disturbed—common after windshield replacement, collision or bumper work, alignments, suspension changes, or low-voltage events. Run a pre-scan with a tool that can access ADAS, ABS, steering, and body modules. Save all DTCs (current, pending, history) and freeze-frame information before clearing anything, and use the results to confirm which driver-assist features your Toyota Fortuner actually has. Then follow OEM service information: confirm stable battery/charging voltage, inspect fuses and grounds, and check connectors and harness routing at the camera and radar for corrosion, pin-fit issues, or strain. Verify the correct windshield specification, an intact and properly bonded camera bracket, and clean, unobstructed sensor viewing zones. Ensure prerequisites are within spec—tire size/pressure, ride height, and alignment—before attempting calibration. After corrections and any required calibration/initialization, complete a post-scan to confirm codes are resolved and do not return. Bang AutoGlass can handle mobile next-day glass service and help coordinate the OEM-required next step.
Static vs Dynamic ADAS Calibration for Toyota Fortuner: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both restore sensor aiming on a Toyota Fortuner, but they are not interchangeable. Static calibration is performed in a controlled space using OEM targets, measurements, and a scan tool. Because geometry is tight, the floor must be level, targets must be placed at the specified distance and height, lighting must be consistent, and the vehicle must be in baseline condition: correct tire size and pressures, normal ride height, and no relevant DTCs that would block the routine. Dynamic calibration is completed on the road. The technician initiates learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, clear lane markings, and a set time or distance. Weather, glare, construction zones, traffic, or inconsistent lane paint can interrupt learning and cause incomplete calibration. Many Toyota Fortuner platforms require static, dynamic, or dual calibration depending on which component was disturbed (camera vs radar), and some require steering angle sensor initialization before ADAS re-enables. Calibration is not a “reset”: if alignment is out of spec, voltage is unstable, or the camera/radar view is obstructed, warnings may return afterward. Bang AutoGlass provides mobile, as-soon-as-next-day service and can help you plan the OEM-required next step.
Proving the Repair Worked on Toyota Fortuner: Post-Scan, Verification Drive, and Documentation
For ADAS-related repairs on a Toyota Fortuner, the absence of a warning light is a good sign, but it is not a complete acceptance test. Start with a post-repair scan across all relevant modules to confirm ADAS-related DTCs are cleared and that no new network, camera, or radar faults are present. If calibration or initialization was performed, keep the completion report showing which systems were calibrated and that each routine finished successfully. Next, validate operation the way the OEM intends. When procedures call for it, perform a verification drive to confirm lane keep assist remains available without frequent dropouts, adaptive cruise control engages and holds, and forward collision warning operates normally. If “system limited” messages return during the drive, treat them as evidence of an unresolved prerequisite or root-cause issue rather than assuming calibration failed. Also verify real-world conditions that impact performance: the windshield camera area is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare affecting the camera’s view. Finally, organize documentation—pre-scan, post-scan, calibration printouts, and road-test notes—for insurance, resale value, and dispute prevention. Bang AutoGlass supports mobile next-day service and backs workmanship with a lifetime warranty.
Services
Service Areas
ADAS Warning Lights on Toyota Fortuner: What the Icons and Messages Commonly Indicate
ADAS warning lights on your Toyota Fortuner mean a driver-assist feature is limited, temporarily disabled, or needs service. The icon often indicates the system: a car between lane lines is Lane Keep Assist/Lane Departure Warning, an “impact” symbol points to Forward Collision Warning or Automatic Emergency Braking, and a speedometer/cruise icon commonly relates to Adaptive Cruise Control. Messages such as “Driver Assist Limited,” “Camera Obscured,” “Front Radar Blocked,” or “ACC Unavailable” usually mean a sensor cannot see clearly enough or the system failed a self-check. Start with the basics. Clean the windshield around the forward camera near the rearview mirror (inside and out), clear frost or fog, and confirm wipers and washer fluid work without streaks. Up front, wipe the radar cover or emblem area and remove bugs, mud, or snow. If the warning started after a rock chip, crack, windshield replacement, or a minor front-end tap, the camera bracket or sensor alignment may be out of tolerance and calibration may be required. Bang AutoGlass offers mobile windshield replacement as soon as next day. Most installs take 30–45 minutes, plus at least 1 hour of safe drive-away time, with a lifetime workmanship warranty and insurance help.
When Calibration Is the Fix for Toyota Fortuner: Post-Windshield Replacement and Sensor Alignment Triggers
For many Toyota Fortuner drivers, calibration is the right fix when ADAS warnings appear after a windshield replacement or any repair that disturbs the forward camera or radar. These systems rely on tight tolerances: the camera bracket angle, windshield specification, and software must agree on what “straight ahead” looks like. OEM procedures commonly call for a learn/calibration whenever the windshield is replaced, a camera or radar is removed/reinstalled, or front-end repairs change sensor position. Calibration is also triggered by vehicle-geometry changes—bumper removal, collision repair, wheel alignment, suspension or ride-height work, steering angle sensor resets, or non-OEM tire sizing. If the vehicle’s “aim” changes, ADAS can disable Lane Keep Assist, Adaptive Cruise Control, and Automatic Emergency Braking until targets are re-established. Best practice is a repeatable workflow: verify the correct windshield for the Toyota Fortuner, confirm the camera mount is clean and secure, run a diagnostic pre-scan, complete OEM static targets and/or dynamic road learning, then perform a post-scan to ensure no codes return. Bang AutoGlass provides mobile windshield replacement as soon as next day (30–45 minutes plus at least 1 hour safe drive-away time) and a lifetime workmanship warranty; we can help coordinate calibration if needed.
When It’s Not Calibration on Toyota Fortuner: Obstructions, Damage, Voltage, Wiring, and Module Faults
On a Toyota Fortuner, an ADAS warning light does not automatically mean calibration is needed. Many systems pause whenever sensor input is unreliable. Weather and road conditions are common causes: heavy rain, snow, fog, glare, or road spray can reduce camera contrast and prevent tracking of lane markings or vehicles, leading to “Camera Obscured” or “Driver Assist Limited.” Features often return once visibility improves. Obstructions and add-ons can create the same symptoms. Dashcams, toll tags, stickers, and poorly placed tint near the camera window can block the forward view. Up front, a cracked, misaligned, or painted radar cover/emblem can interrupt the signal and trigger “Front Radar Blocked” or “ACC Unavailable.” Electrical stability matters, too: a weak 12-volt battery or recent battery disconnect can set low-voltage or communication faults that take modules offline. If warnings persist after cleaning, treat it as diagnostics. A DTC scan helps distinguish a blocked sensor from fuse, ground, connector, corrosion, harness, camera/radar unit, or software issues. If the warning began after windshield damage, replacement, or a front-end impact, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Toyota Fortuner: Reading DTCs, Root-Cause Checks, and OEM Procedures
On a modern Toyota Fortuner, clearing ADAS warning lights starts with scan data, not parts swapping. The dash icon only tells you a system is limited; it does not identify the trigger. Many OEM procedures call for a pre-repair health scan whenever the windshield camera, front radar, ABS/steering inputs, or related wiring has been disturbed—common after windshield replacement, collision or bumper work, alignments, suspension changes, or low-voltage events. Run a pre-scan with a tool that can access ADAS, ABS, steering, and body modules. Save all DTCs (current, pending, history) and freeze-frame information before clearing anything, and use the results to confirm which driver-assist features your Toyota Fortuner actually has. Then follow OEM service information: confirm stable battery/charging voltage, inspect fuses and grounds, and check connectors and harness routing at the camera and radar for corrosion, pin-fit issues, or strain. Verify the correct windshield specification, an intact and properly bonded camera bracket, and clean, unobstructed sensor viewing zones. Ensure prerequisites are within spec—tire size/pressure, ride height, and alignment—before attempting calibration. After corrections and any required calibration/initialization, complete a post-scan to confirm codes are resolved and do not return. Bang AutoGlass can handle mobile next-day glass service and help coordinate the OEM-required next step.
Static vs Dynamic ADAS Calibration for Toyota Fortuner: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both restore sensor aiming on a Toyota Fortuner, but they are not interchangeable. Static calibration is performed in a controlled space using OEM targets, measurements, and a scan tool. Because geometry is tight, the floor must be level, targets must be placed at the specified distance and height, lighting must be consistent, and the vehicle must be in baseline condition: correct tire size and pressures, normal ride height, and no relevant DTCs that would block the routine. Dynamic calibration is completed on the road. The technician initiates learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, clear lane markings, and a set time or distance. Weather, glare, construction zones, traffic, or inconsistent lane paint can interrupt learning and cause incomplete calibration. Many Toyota Fortuner platforms require static, dynamic, or dual calibration depending on which component was disturbed (camera vs radar), and some require steering angle sensor initialization before ADAS re-enables. Calibration is not a “reset”: if alignment is out of spec, voltage is unstable, or the camera/radar view is obstructed, warnings may return afterward. Bang AutoGlass provides mobile, as-soon-as-next-day service and can help you plan the OEM-required next step.
Proving the Repair Worked on Toyota Fortuner: Post-Scan, Verification Drive, and Documentation
For ADAS-related repairs on a Toyota Fortuner, the absence of a warning light is a good sign, but it is not a complete acceptance test. Start with a post-repair scan across all relevant modules to confirm ADAS-related DTCs are cleared and that no new network, camera, or radar faults are present. If calibration or initialization was performed, keep the completion report showing which systems were calibrated and that each routine finished successfully. Next, validate operation the way the OEM intends. When procedures call for it, perform a verification drive to confirm lane keep assist remains available without frequent dropouts, adaptive cruise control engages and holds, and forward collision warning operates normally. If “system limited” messages return during the drive, treat them as evidence of an unresolved prerequisite or root-cause issue rather than assuming calibration failed. Also verify real-world conditions that impact performance: the windshield camera area is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare affecting the camera’s view. Finally, organize documentation—pre-scan, post-scan, calibration printouts, and road-test notes—for insurance, resale value, and dispute prevention. Bang AutoGlass supports mobile next-day service and backs workmanship with a lifetime warranty.
Services
Service Areas
ADAS Warning Lights on Toyota Fortuner: What the Icons and Messages Commonly Indicate
ADAS warning lights on your Toyota Fortuner mean a driver-assist feature is limited, temporarily disabled, or needs service. The icon often indicates the system: a car between lane lines is Lane Keep Assist/Lane Departure Warning, an “impact” symbol points to Forward Collision Warning or Automatic Emergency Braking, and a speedometer/cruise icon commonly relates to Adaptive Cruise Control. Messages such as “Driver Assist Limited,” “Camera Obscured,” “Front Radar Blocked,” or “ACC Unavailable” usually mean a sensor cannot see clearly enough or the system failed a self-check. Start with the basics. Clean the windshield around the forward camera near the rearview mirror (inside and out), clear frost or fog, and confirm wipers and washer fluid work without streaks. Up front, wipe the radar cover or emblem area and remove bugs, mud, or snow. If the warning started after a rock chip, crack, windshield replacement, or a minor front-end tap, the camera bracket or sensor alignment may be out of tolerance and calibration may be required. Bang AutoGlass offers mobile windshield replacement as soon as next day. Most installs take 30–45 minutes, plus at least 1 hour of safe drive-away time, with a lifetime workmanship warranty and insurance help.
When Calibration Is the Fix for Toyota Fortuner: Post-Windshield Replacement and Sensor Alignment Triggers
For many Toyota Fortuner drivers, calibration is the right fix when ADAS warnings appear after a windshield replacement or any repair that disturbs the forward camera or radar. These systems rely on tight tolerances: the camera bracket angle, windshield specification, and software must agree on what “straight ahead” looks like. OEM procedures commonly call for a learn/calibration whenever the windshield is replaced, a camera or radar is removed/reinstalled, or front-end repairs change sensor position. Calibration is also triggered by vehicle-geometry changes—bumper removal, collision repair, wheel alignment, suspension or ride-height work, steering angle sensor resets, or non-OEM tire sizing. If the vehicle’s “aim” changes, ADAS can disable Lane Keep Assist, Adaptive Cruise Control, and Automatic Emergency Braking until targets are re-established. Best practice is a repeatable workflow: verify the correct windshield for the Toyota Fortuner, confirm the camera mount is clean and secure, run a diagnostic pre-scan, complete OEM static targets and/or dynamic road learning, then perform a post-scan to ensure no codes return. Bang AutoGlass provides mobile windshield replacement as soon as next day (30–45 minutes plus at least 1 hour safe drive-away time) and a lifetime workmanship warranty; we can help coordinate calibration if needed.
When It’s Not Calibration on Toyota Fortuner: Obstructions, Damage, Voltage, Wiring, and Module Faults
On a Toyota Fortuner, an ADAS warning light does not automatically mean calibration is needed. Many systems pause whenever sensor input is unreliable. Weather and road conditions are common causes: heavy rain, snow, fog, glare, or road spray can reduce camera contrast and prevent tracking of lane markings or vehicles, leading to “Camera Obscured” or “Driver Assist Limited.” Features often return once visibility improves. Obstructions and add-ons can create the same symptoms. Dashcams, toll tags, stickers, and poorly placed tint near the camera window can block the forward view. Up front, a cracked, misaligned, or painted radar cover/emblem can interrupt the signal and trigger “Front Radar Blocked” or “ACC Unavailable.” Electrical stability matters, too: a weak 12-volt battery or recent battery disconnect can set low-voltage or communication faults that take modules offline. If warnings persist after cleaning, treat it as diagnostics. A DTC scan helps distinguish a blocked sensor from fuse, ground, connector, corrosion, harness, camera/radar unit, or software issues. If the warning began after windshield damage, replacement, or a front-end impact, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Toyota Fortuner: Reading DTCs, Root-Cause Checks, and OEM Procedures
On a modern Toyota Fortuner, clearing ADAS warning lights starts with scan data, not parts swapping. The dash icon only tells you a system is limited; it does not identify the trigger. Many OEM procedures call for a pre-repair health scan whenever the windshield camera, front radar, ABS/steering inputs, or related wiring has been disturbed—common after windshield replacement, collision or bumper work, alignments, suspension changes, or low-voltage events. Run a pre-scan with a tool that can access ADAS, ABS, steering, and body modules. Save all DTCs (current, pending, history) and freeze-frame information before clearing anything, and use the results to confirm which driver-assist features your Toyota Fortuner actually has. Then follow OEM service information: confirm stable battery/charging voltage, inspect fuses and grounds, and check connectors and harness routing at the camera and radar for corrosion, pin-fit issues, or strain. Verify the correct windshield specification, an intact and properly bonded camera bracket, and clean, unobstructed sensor viewing zones. Ensure prerequisites are within spec—tire size/pressure, ride height, and alignment—before attempting calibration. After corrections and any required calibration/initialization, complete a post-scan to confirm codes are resolved and do not return. Bang AutoGlass can handle mobile next-day glass service and help coordinate the OEM-required next step.
Static vs Dynamic ADAS Calibration for Toyota Fortuner: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both restore sensor aiming on a Toyota Fortuner, but they are not interchangeable. Static calibration is performed in a controlled space using OEM targets, measurements, and a scan tool. Because geometry is tight, the floor must be level, targets must be placed at the specified distance and height, lighting must be consistent, and the vehicle must be in baseline condition: correct tire size and pressures, normal ride height, and no relevant DTCs that would block the routine. Dynamic calibration is completed on the road. The technician initiates learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, clear lane markings, and a set time or distance. Weather, glare, construction zones, traffic, or inconsistent lane paint can interrupt learning and cause incomplete calibration. Many Toyota Fortuner platforms require static, dynamic, or dual calibration depending on which component was disturbed (camera vs radar), and some require steering angle sensor initialization before ADAS re-enables. Calibration is not a “reset”: if alignment is out of spec, voltage is unstable, or the camera/radar view is obstructed, warnings may return afterward. Bang AutoGlass provides mobile, as-soon-as-next-day service and can help you plan the OEM-required next step.
Proving the Repair Worked on Toyota Fortuner: Post-Scan, Verification Drive, and Documentation
For ADAS-related repairs on a Toyota Fortuner, the absence of a warning light is a good sign, but it is not a complete acceptance test. Start with a post-repair scan across all relevant modules to confirm ADAS-related DTCs are cleared and that no new network, camera, or radar faults are present. If calibration or initialization was performed, keep the completion report showing which systems were calibrated and that each routine finished successfully. Next, validate operation the way the OEM intends. When procedures call for it, perform a verification drive to confirm lane keep assist remains available without frequent dropouts, adaptive cruise control engages and holds, and forward collision warning operates normally. If “system limited” messages return during the drive, treat them as evidence of an unresolved prerequisite or root-cause issue rather than assuming calibration failed. Also verify real-world conditions that impact performance: the windshield camera area is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare affecting the camera’s view. Finally, organize documentation—pre-scan, post-scan, calibration printouts, and road-test notes—for insurance, resale value, and dispute prevention. Bang AutoGlass supports mobile next-day service and backs workmanship with a lifetime warranty.
Enjoy More Relevant Blogs
Do You Need ADAS Calibration for Toyota Fortuner After a Wheel Alignment, Suspension Work, or a Minor Collision?
Do you need ADAS calibration for a Toyota Fortuner after alignment, suspension work, or a minor collision? Signs, timelines, safety risks, and costs today.
Pre- and Post-Calibration Scans for Toyota Fortuner: Proving Systems Are Set Correctly
Pre- and post-calibration scans for Toyota Fortuner: see why scans matter, what they verify, and how reports prove ADAS systems are set correctly after service.
How to Schedule ADAS Calibration for Toyota Fortuner After Windshield Replacement
Schedule ADAS calibration for Toyota Fortuner after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
Mobile ADAS Calibration for Toyota Fortuner: What to Expect On-Site and Why Setup Matters
Mobile ADAS calibration for Toyota Fortuner: what to expect on-site, space and lighting needs, and why setup and verification matter after repairs today.
ADAS Calibration Checklist for Toyota Fortuner: Documentation, Verification, and Final Safety Checks
ADAS calibration checklist for Toyota Fortuner: documentation to request, scans to verify, and safety checks that confirm cameras and sensors are set right.
Camera Calibration for Toyota Fortuner: Lane Assist and Forward Collision Accuracy Explained
Need camera calibration for your Toyota Fortuner? See how calibration affects lane assist and forward collision accuracy after windshield service or repairs.
OEM Calibration Requirements for Toyota Fortuner: How to Confirm What Must Be Calibrated
OEM calibration requirements for Toyota Fortuner: how to confirm what must be calibrated after repairs, what triggers recalibration, and what proof to ask for.
Static vs Dynamic ADAS Calibration for Toyota Fortuner: What the Difference Means
Static vs dynamic ADAS calibration for Toyota Fortuner: key differences, when each is required, how long it takes, and what affects accuracy for safety.
How Much Does ADAS Calibration Cost for Toyota Fortuner? What Drives Pricing and What Insurance Typically Covers
How much does ADAS calibration cost for a Toyota Fortuner? Learn pricing drivers, camera vs radar needs, labor time, and what insurance typically covers.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm