Services
Service Areas
Do You Need ADAS Calibration for Toyota Highlander After a Wheel Alignment, Suspension Work, or a Minor Collision?
Do You Need ADAS Calibration for Toyota Highlander After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
A Toyota Highlander can drive straight after an alignment and still have ADAS that’s slightly out of sync if the reference angles changed. Lane-keeping assist and lane departure warning use lane lines from the forward camera, but the software also depends on the vehicle’s calibrated centerline and an accurate steering angle sensor (SAS) baseline. ACC and AEB likewise assume the camera/radar are aimed relative to the true direction of travel. When a technician adjusts toe, camber, caster, or corrects thrust angle, the Toyota Highlander may follow a subtly different path than before. If the SAS zero point and sensor aiming are not updated, the system can misread what “straight ahead” is. That’s why OEM workflows often pair alignment with a scan-tool routine: pre-scan for stored codes, SAS reset or relearn, then calibration verification for the front camera and/or radar using static targets, a dynamic road drive, or both. A practical red flag is an alignment invoice with no post-scan results or calibration documentation. In real driving, miscalibration can feel like drifting lane centering, ACC that changes following behavior unexpectedly, or warnings that trigger too early or too late. Choose providers that confirm alignment specs first and then record the calibration outcome.
Toyota Highlander ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Toyota Highlander—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Toyota Highlander set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Toyota Highlander After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
After a minor collision in a Toyota Highlander, ADAS calibration is commonly missed because the car may appear normal. However, radar and camera assemblies are aimed within very small tolerances. A low-speed rear-end, parking-lot hit, or curb strike can shift a radar bracket behind the bumper cover or disturb a camera mount by only millimeters, yet that can change how ACC, AEB, lane-keeping assist, and forward collision warning behave. It also may not set a warning light; some systems log diagnostic trouble codes that only show on a scan, while others operate with reduced accuracy until you notice phantom alerts or inconsistent following distance. A safer workflow is a diagnostic pre-scan, any manufacturer-required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status, with the calibration report saved for your records and insurance file. If the impact also caused a chipped or cracked windshield—especially on Toyota Highlander trims with windshield-mounted cameras—Bang AutoGlass can provide mobile windshield replacement when scheduling allows. Most installs take 30–45 minutes, and we recommend at least one hour of safe drive time for adhesive cure. We can also help you document what happened and connect you to an appropriate calibration resource.
Signs Your Toyota Highlander ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
If your Toyota Highlander has ADAS, a warning light for the camera, radar, or lane assist is the obvious sign calibration may be needed. Many issues show up earlier as behavior that feels "off." Notice lane-keeping assist pulling you off-center, lane departure alerts firing too often, or lane-centering that wanders instead of holding steady. Adaptive cruise control (ACC) can also change: inconsistent following distance, abrupt braking, or unexpected speed changes may mean the camera or radar view is no longer aligned with the vehicle's centerline. Other clues include false forward-collision warnings or blind-spot monitoring that misses vehicles. If this started right after windshield replacement with a windshield-mounted camera, wheel alignment, suspension/steering work, bumper repair, or a minor hit, assume calibration prerequisites shifted. The fix is a scan for codes and an OEM-procedure static and/or dynamic calibration, documented with a calibration report. For searches like "Toyota Highlander ADAS calibration near me," choose a shop that can scan, calibrate, and provide paperwork. If damaged glass is involved, Bang AutoGlass offers next-day mobile windshield replacement. Installs usually take 30-45 minutes plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
How Shops Confirm Toyota Highlander ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
To verify your Toyota Highlander ADAS is truly in-spec, a quality shop relies on process and documentation, not a quick drive. Step one is a pre-repair diagnostic scan to capture diagnostic trouble codes (DTCs), module communication status, and any stored ADAS history faults. Next, they confirm the mechanical items that make calibration valid: correct tire size and pressure, proper ride height, no looseness in steering or suspension, and a four-wheel alignment within spec (including thrust angle). Because ADAS targets vehicle geometry, even small alignment or ride-height errors can compromise camera calibration and radar calibration. With prerequisites met, the shop checks the exact ADAS configuration on your Toyota Highlander and selects the required OEM procedures for the repair event. Calibration may be static (targets placed at measured distances and heights on a level floor with controlled lighting) and/or dynamic (a scan-tool initiated road routine completed under defined speed, lane-marking, and weather conditions). After the routine, a post-scan confirms codes are cleared and systems report normal operation. Ask for proof: pre-scan/post-scan printouts, alignment measurements when applicable, and the ADAS calibration report (certificate) showing successful completion and final status.
Insurance and Warranty Questions for Toyota Highlander ADAS Calibration: What’s Typically Covered and What to Document
For Toyota Highlander owners, ADAS calibration usually raises two questions: will insurance pay, and what records should you keep? Coverage depends on the trigger. If calibration is needed because of collision repair (bumper damage, sensor bracket replacement, suspension impact), it is commonly addressed under collision coverage. If calibration is required after windshield replacement on a Toyota Highlander with a windshield-mounted camera, it is often processed under comprehensive coverage. Carrier rules, deductibles, and policy language vary, so confirm whether scanning, aiming, and camera/radar calibration are reimbursable line items. Your best strategy is to document the chain of necessity. Keep a repair order that states the event (windshield replacement, alignment, suspension work, or minor collision), photos of the affected area, alignment reports if geometry was involved, and the pre-scan/post-scan printouts. The critical item is the ADAS calibration report showing the procedure completed and a final pass status. Itemized invoices that separate glass, scanning, and calibration help prevent confusion. Bang AutoGlass can assist with the glass portion and paperwork. We work with all insurance companies when comprehensive coverage applies and offer next-day mobile service when scheduling allows. Most windshield replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
Services
Service Areas
Do You Need ADAS Calibration for Toyota Highlander After a Wheel Alignment, Suspension Work, or a Minor Collision?
Do You Need ADAS Calibration for Toyota Highlander After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
A Toyota Highlander can drive straight after an alignment and still have ADAS that’s slightly out of sync if the reference angles changed. Lane-keeping assist and lane departure warning use lane lines from the forward camera, but the software also depends on the vehicle’s calibrated centerline and an accurate steering angle sensor (SAS) baseline. ACC and AEB likewise assume the camera/radar are aimed relative to the true direction of travel. When a technician adjusts toe, camber, caster, or corrects thrust angle, the Toyota Highlander may follow a subtly different path than before. If the SAS zero point and sensor aiming are not updated, the system can misread what “straight ahead” is. That’s why OEM workflows often pair alignment with a scan-tool routine: pre-scan for stored codes, SAS reset or relearn, then calibration verification for the front camera and/or radar using static targets, a dynamic road drive, or both. A practical red flag is an alignment invoice with no post-scan results or calibration documentation. In real driving, miscalibration can feel like drifting lane centering, ACC that changes following behavior unexpectedly, or warnings that trigger too early or too late. Choose providers that confirm alignment specs first and then record the calibration outcome.
Toyota Highlander ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Toyota Highlander—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Toyota Highlander set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Toyota Highlander After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
After a minor collision in a Toyota Highlander, ADAS calibration is commonly missed because the car may appear normal. However, radar and camera assemblies are aimed within very small tolerances. A low-speed rear-end, parking-lot hit, or curb strike can shift a radar bracket behind the bumper cover or disturb a camera mount by only millimeters, yet that can change how ACC, AEB, lane-keeping assist, and forward collision warning behave. It also may not set a warning light; some systems log diagnostic trouble codes that only show on a scan, while others operate with reduced accuracy until you notice phantom alerts or inconsistent following distance. A safer workflow is a diagnostic pre-scan, any manufacturer-required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status, with the calibration report saved for your records and insurance file. If the impact also caused a chipped or cracked windshield—especially on Toyota Highlander trims with windshield-mounted cameras—Bang AutoGlass can provide mobile windshield replacement when scheduling allows. Most installs take 30–45 minutes, and we recommend at least one hour of safe drive time for adhesive cure. We can also help you document what happened and connect you to an appropriate calibration resource.
Signs Your Toyota Highlander ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
If your Toyota Highlander has ADAS, a warning light for the camera, radar, or lane assist is the obvious sign calibration may be needed. Many issues show up earlier as behavior that feels "off." Notice lane-keeping assist pulling you off-center, lane departure alerts firing too often, or lane-centering that wanders instead of holding steady. Adaptive cruise control (ACC) can also change: inconsistent following distance, abrupt braking, or unexpected speed changes may mean the camera or radar view is no longer aligned with the vehicle's centerline. Other clues include false forward-collision warnings or blind-spot monitoring that misses vehicles. If this started right after windshield replacement with a windshield-mounted camera, wheel alignment, suspension/steering work, bumper repair, or a minor hit, assume calibration prerequisites shifted. The fix is a scan for codes and an OEM-procedure static and/or dynamic calibration, documented with a calibration report. For searches like "Toyota Highlander ADAS calibration near me," choose a shop that can scan, calibrate, and provide paperwork. If damaged glass is involved, Bang AutoGlass offers next-day mobile windshield replacement. Installs usually take 30-45 minutes plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
How Shops Confirm Toyota Highlander ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
To verify your Toyota Highlander ADAS is truly in-spec, a quality shop relies on process and documentation, not a quick drive. Step one is a pre-repair diagnostic scan to capture diagnostic trouble codes (DTCs), module communication status, and any stored ADAS history faults. Next, they confirm the mechanical items that make calibration valid: correct tire size and pressure, proper ride height, no looseness in steering or suspension, and a four-wheel alignment within spec (including thrust angle). Because ADAS targets vehicle geometry, even small alignment or ride-height errors can compromise camera calibration and radar calibration. With prerequisites met, the shop checks the exact ADAS configuration on your Toyota Highlander and selects the required OEM procedures for the repair event. Calibration may be static (targets placed at measured distances and heights on a level floor with controlled lighting) and/or dynamic (a scan-tool initiated road routine completed under defined speed, lane-marking, and weather conditions). After the routine, a post-scan confirms codes are cleared and systems report normal operation. Ask for proof: pre-scan/post-scan printouts, alignment measurements when applicable, and the ADAS calibration report (certificate) showing successful completion and final status.
Insurance and Warranty Questions for Toyota Highlander ADAS Calibration: What’s Typically Covered and What to Document
For Toyota Highlander owners, ADAS calibration usually raises two questions: will insurance pay, and what records should you keep? Coverage depends on the trigger. If calibration is needed because of collision repair (bumper damage, sensor bracket replacement, suspension impact), it is commonly addressed under collision coverage. If calibration is required after windshield replacement on a Toyota Highlander with a windshield-mounted camera, it is often processed under comprehensive coverage. Carrier rules, deductibles, and policy language vary, so confirm whether scanning, aiming, and camera/radar calibration are reimbursable line items. Your best strategy is to document the chain of necessity. Keep a repair order that states the event (windshield replacement, alignment, suspension work, or minor collision), photos of the affected area, alignment reports if geometry was involved, and the pre-scan/post-scan printouts. The critical item is the ADAS calibration report showing the procedure completed and a final pass status. Itemized invoices that separate glass, scanning, and calibration help prevent confusion. Bang AutoGlass can assist with the glass portion and paperwork. We work with all insurance companies when comprehensive coverage applies and offer next-day mobile service when scheduling allows. Most windshield replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
Services
Service Areas
Do You Need ADAS Calibration for Toyota Highlander After a Wheel Alignment, Suspension Work, or a Minor Collision?
Do You Need ADAS Calibration for Toyota Highlander After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
A Toyota Highlander can drive straight after an alignment and still have ADAS that’s slightly out of sync if the reference angles changed. Lane-keeping assist and lane departure warning use lane lines from the forward camera, but the software also depends on the vehicle’s calibrated centerline and an accurate steering angle sensor (SAS) baseline. ACC and AEB likewise assume the camera/radar are aimed relative to the true direction of travel. When a technician adjusts toe, camber, caster, or corrects thrust angle, the Toyota Highlander may follow a subtly different path than before. If the SAS zero point and sensor aiming are not updated, the system can misread what “straight ahead” is. That’s why OEM workflows often pair alignment with a scan-tool routine: pre-scan for stored codes, SAS reset or relearn, then calibration verification for the front camera and/or radar using static targets, a dynamic road drive, or both. A practical red flag is an alignment invoice with no post-scan results or calibration documentation. In real driving, miscalibration can feel like drifting lane centering, ACC that changes following behavior unexpectedly, or warnings that trigger too early or too late. Choose providers that confirm alignment specs first and then record the calibration outcome.
Toyota Highlander ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Toyota Highlander—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Toyota Highlander set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Toyota Highlander After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
After a minor collision in a Toyota Highlander, ADAS calibration is commonly missed because the car may appear normal. However, radar and camera assemblies are aimed within very small tolerances. A low-speed rear-end, parking-lot hit, or curb strike can shift a radar bracket behind the bumper cover or disturb a camera mount by only millimeters, yet that can change how ACC, AEB, lane-keeping assist, and forward collision warning behave. It also may not set a warning light; some systems log diagnostic trouble codes that only show on a scan, while others operate with reduced accuracy until you notice phantom alerts or inconsistent following distance. A safer workflow is a diagnostic pre-scan, any manufacturer-required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status, with the calibration report saved for your records and insurance file. If the impact also caused a chipped or cracked windshield—especially on Toyota Highlander trims with windshield-mounted cameras—Bang AutoGlass can provide mobile windshield replacement when scheduling allows. Most installs take 30–45 minutes, and we recommend at least one hour of safe drive time for adhesive cure. We can also help you document what happened and connect you to an appropriate calibration resource.
Signs Your Toyota Highlander ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
If your Toyota Highlander has ADAS, a warning light for the camera, radar, or lane assist is the obvious sign calibration may be needed. Many issues show up earlier as behavior that feels "off." Notice lane-keeping assist pulling you off-center, lane departure alerts firing too often, or lane-centering that wanders instead of holding steady. Adaptive cruise control (ACC) can also change: inconsistent following distance, abrupt braking, or unexpected speed changes may mean the camera or radar view is no longer aligned with the vehicle's centerline. Other clues include false forward-collision warnings or blind-spot monitoring that misses vehicles. If this started right after windshield replacement with a windshield-mounted camera, wheel alignment, suspension/steering work, bumper repair, or a minor hit, assume calibration prerequisites shifted. The fix is a scan for codes and an OEM-procedure static and/or dynamic calibration, documented with a calibration report. For searches like "Toyota Highlander ADAS calibration near me," choose a shop that can scan, calibrate, and provide paperwork. If damaged glass is involved, Bang AutoGlass offers next-day mobile windshield replacement. Installs usually take 30-45 minutes plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
How Shops Confirm Toyota Highlander ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
To verify your Toyota Highlander ADAS is truly in-spec, a quality shop relies on process and documentation, not a quick drive. Step one is a pre-repair diagnostic scan to capture diagnostic trouble codes (DTCs), module communication status, and any stored ADAS history faults. Next, they confirm the mechanical items that make calibration valid: correct tire size and pressure, proper ride height, no looseness in steering or suspension, and a four-wheel alignment within spec (including thrust angle). Because ADAS targets vehicle geometry, even small alignment or ride-height errors can compromise camera calibration and radar calibration. With prerequisites met, the shop checks the exact ADAS configuration on your Toyota Highlander and selects the required OEM procedures for the repair event. Calibration may be static (targets placed at measured distances and heights on a level floor with controlled lighting) and/or dynamic (a scan-tool initiated road routine completed under defined speed, lane-marking, and weather conditions). After the routine, a post-scan confirms codes are cleared and systems report normal operation. Ask for proof: pre-scan/post-scan printouts, alignment measurements when applicable, and the ADAS calibration report (certificate) showing successful completion and final status.
Insurance and Warranty Questions for Toyota Highlander ADAS Calibration: What’s Typically Covered and What to Document
For Toyota Highlander owners, ADAS calibration usually raises two questions: will insurance pay, and what records should you keep? Coverage depends on the trigger. If calibration is needed because of collision repair (bumper damage, sensor bracket replacement, suspension impact), it is commonly addressed under collision coverage. If calibration is required after windshield replacement on a Toyota Highlander with a windshield-mounted camera, it is often processed under comprehensive coverage. Carrier rules, deductibles, and policy language vary, so confirm whether scanning, aiming, and camera/radar calibration are reimbursable line items. Your best strategy is to document the chain of necessity. Keep a repair order that states the event (windshield replacement, alignment, suspension work, or minor collision), photos of the affected area, alignment reports if geometry was involved, and the pre-scan/post-scan printouts. The critical item is the ADAS calibration report showing the procedure completed and a final pass status. Itemized invoices that separate glass, scanning, and calibration help prevent confusion. Bang AutoGlass can assist with the glass portion and paperwork. We work with all insurance companies when comprehensive coverage applies and offer next-day mobile service when scheduling allows. Most windshield replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
Enjoy More Relevant Blogs
OEM Calibration Requirements for Toyota Highlander: How to Confirm What Must Be Calibrated
OEM calibration requirements for Toyota Highlander: how to confirm what must be calibrated after repairs, what triggers recalibration, and what proof to ask for.
Pre- and Post-Calibration Scans for Toyota Highlander: Proving Systems Are Set Correctly
Pre- and post-calibration scans for Toyota Highlander: see why scans matter, what they verify, and how reports prove ADAS systems are set correctly after service.
Mobile ADAS Calibration for Toyota Highlander: What to Expect On-Site and Why Setup Matters
Mobile ADAS calibration for Toyota Highlander: what to expect on-site, space and lighting needs, and why setup and verification matter after repairs today.
ADAS Calibration Checklist for Toyota Highlander: Documentation, Verification, and Final Safety Checks
ADAS calibration checklist for Toyota Highlander: documentation to request, scans to verify, and safety checks that confirm cameras and sensors are set right.
Static vs Dynamic ADAS Calibration for Toyota Highlander: What the Difference Means
Static vs dynamic ADAS calibration for Toyota Highlander: key differences, when each is required, how long it takes, and what affects accuracy for safety.
ADAS Warning Lights on Toyota Highlander: When Calibration Is the Fix and When It’s Not
ADAS warning lights on your Toyota Highlander? Learn when calibration fixes lane assist or AEB issues, when it will not, and what to check next. Schedule help.
How to Schedule ADAS Calibration for Toyota Highlander After Windshield Replacement
Schedule ADAS calibration for Toyota Highlander after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
Camera Calibration for Toyota Highlander: Lane Assist and Forward Collision Accuracy Explained
Need camera calibration for your Toyota Highlander? See how calibration affects lane assist and forward collision accuracy after windshield service or repairs.
How Much Does ADAS Calibration Cost for Toyota Highlander? What Drives Pricing and What Insurance Typically Covers
How much does ADAS calibration cost for a Toyota Highlander? Learn pricing drivers, camera vs radar needs, labor time, and what insurance typically covers.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm