Services
Service Areas
Shattered Back Window on Toyota Rav4 Prime: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Toyota Rav4 Prime: Safety, Visibility, and Securing the Vehicle
If the rear window on your Toyota Rav4 Prime shatters, treat it as a safety and security issue until a professional rear window replacement is completed. If it breaks while driving, slow down, turn on hazard lights, and pull into a safe, well-lit area. Tempered back glass fractures into small cubes, but they can still cut skin and irritate eyes--avoid touching your face and keep children and pets away. With gloves and eye protection, remove only loose pieces that block visibility or could drop into the cabin. Next, protect the interior from weather and theft. Remove valuables and cover the opening with plastic sheeting or a heavy-duty bag, securing it with painter's tape or other low-tack tape. Do not slam doors or the hatch; pressure changes can dislodge remaining glass. Take photos for an insurance claim, since rear glass damage is commonly handled under comprehensive coverage. Bang AutoGlass makes Toyota Rav4 Prime back glass replacement straightforward with fully mobile service, often as soon as next day. Most installs take about 30-45 minutes on site, then the urethane requires at least 1 hour of cure time before safe drive-away. Every job is backed by our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A broken rear window means your Toyota Rav4 Prime likely has glass in the rear deck, seat seams, and trunk/cargo area. Clean it in stages so you do not drive shards deeper into upholstery. Put on safety glasses, thick gloves, and sturdy shoes, and keep unprotected passengers out of the work area. If available, lay plastic sheeting over seats and the cargo floor before you start lifting pieces. Start with big fragments. Pick larger chunks from the window frame and rear deck and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong vacuum using a crevice tool. Follow a top-down route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk well, including the spare-tire compartment. After the first vacuum, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from fabric and corners; repeat until the tape comes back clean. Finish by wiping plastics with a slightly damp microfiber towel rather than scrubbing. If you have mobile rear glass replacement scheduled with Bang AutoGlass, clear loose debris around the opening so the bond area stays clean.
Confirm the Correct Rear Glass for Toyota Rav4 Prime: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Before you replace the rear window on a Toyota Rav4 Prime, confirm which back glass the vehicle needs. VIN validation or a parts lookup is the safest method because option differences change the glass. Start with the rear defroster: the replacement must include the correct heating grid and the proper terminal tabs so the factory connectors attach securely. Also verify antenna features. Many vehicles embed AM/FM, GPS, or cellular traces in the rear glass; if your reception relied on those lines, choose an antenna-equipped replacement. Tint matching matters as well. Rear glass may be clear, lightly tinted, or privacy glass with a darker factory shade. Matching tint supports a uniform look, better heat rejection, and local compliance. If your Toyota Rav4 Prime had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after installation. Finally, verify the certification stamp. Automotive glass includes DOT identification and AS markings (AS2/AS3 are common on rear/side glass and can indicate tinted variations). Correct markings and the part number help ensure proper curvature and tempered-glass performance. Bang AutoGlass verifies these details before mobile dispatch and backs every install with our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
A quality rear glass replacement starts with careful removal and prep for your Toyota Rav4 Prime. Bang AutoGlass covers the seats, rear deck, and cargo area, then removes trim, clips, and moldings needed to access the opening without scuffing interior panels. We clear tempered-glass fragments, manage rear defroster/antenna connectors, and cut the existing urethane with controlled tools so the vehicle aperture stays intact. Next we inspect the pinchweld-the metal bonding flange the urethane bonds to. Best practice is to remove most of the old urethane while leaving a thin, uniform base layer (about 1-2 mm) so new urethane bonds to cured urethane instead of bare metal. If we find scratches through paint, corrosion, or prior bodywork issues, we correct and prime/seal exposed metal because rust under the bond line is a common cause of leaks and adhesion loss. Finally, we dry-fit the replacement back glass for your Toyota Rav4 Prime, confirm spacers and molding condition, clean the frit and aperture, and apply the proper primers/activators with correct flash times. With surfaces ready, we set the glass with even pressure for a consistent perimeter seal-mobile, next-day rear window replacement backed by our lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Toyota Rav4 Prime: What Controls Safe Release
The difference between "installed" and "safe" after a Toyota Rav4 Prime rear window replacement is urethane curing. Auto glass urethane is a moisture-curing polyurethane adhesive, and each system includes Safe Drive-Away Time (SDAT) guidance tied to minimum bond strength. SDAT is controlled by the adhesive used, proper surface prep, bead size/shape, and environmental conditions like temperature and humidity. Cold or very dry air can slow cure; warm, humid conditions typically speed it up. Open-time limits also matter-urethane must be applied and the glass set within the specified window for proper wet-out and adhesion. Prep details directly affect the bond: clean, contaminant-free surfaces; correct primer/activator application; and required flash times. The urethane bead must be continuous and uniform so it compresses evenly around the perimeter, preventing thin spots that can leak or whistle. Exposed metal on the pinchweld must be protected and primed because corrosion under the bond line is a common long-term failure point. At Bang AutoGlass, most Toyota Rav4 Prime back glass replacements take about 30-45 minutes on site, then we require at least 1 hour before safe drive-away. Drive gently, avoid slamming doors, and skip automated car washes; we'll extend cure time if conditions warrant it, backed by our lifetime workmanship warranty and help with comprehensive coverage claims.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
Post-install checks turn a rear glass replacement on your Toyota Rav4 Prime into a dependable repair. First, verify features: rear defroster tabs should be seated securely, and connectors should be aligned and strain-relieved so hatch or trunk movement doesn't pull leads loose. If your Toyota Rav4 Prime uses in-glass antennas, those connections must be restored to avoid degraded AM/FM reception. A quick functional confirmation on site is the fastest way to catch a connection issue early. Next, confirm water and air sealing. Even spacing around the perimeter and a clean reveal line indicate proper set-down and molding alignment. A controlled perimeter water test helps confirm the urethane bond line is sealed, and a short road test (when practical) reproduces highway airflow to check for wind noise; a new whistle usually points to a small gap or mis-seated molding. Finally, keep records and follow care guidance. You should have documentation of the glass type installed (tint, defroster grid, antenna integration, and DOT/AS stamp) and a clear warranty record. Bang AutoGlass provides an invoice and backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time, avoid slamming doors right after service, and skip automated car washes for the first day to protect the fresh adhesive seal.
Services
Service Areas
Shattered Back Window on Toyota Rav4 Prime: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Toyota Rav4 Prime: Safety, Visibility, and Securing the Vehicle
If the rear window on your Toyota Rav4 Prime shatters, treat it as a safety and security issue until a professional rear window replacement is completed. If it breaks while driving, slow down, turn on hazard lights, and pull into a safe, well-lit area. Tempered back glass fractures into small cubes, but they can still cut skin and irritate eyes--avoid touching your face and keep children and pets away. With gloves and eye protection, remove only loose pieces that block visibility or could drop into the cabin. Next, protect the interior from weather and theft. Remove valuables and cover the opening with plastic sheeting or a heavy-duty bag, securing it with painter's tape or other low-tack tape. Do not slam doors or the hatch; pressure changes can dislodge remaining glass. Take photos for an insurance claim, since rear glass damage is commonly handled under comprehensive coverage. Bang AutoGlass makes Toyota Rav4 Prime back glass replacement straightforward with fully mobile service, often as soon as next day. Most installs take about 30-45 minutes on site, then the urethane requires at least 1 hour of cure time before safe drive-away. Every job is backed by our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A broken rear window means your Toyota Rav4 Prime likely has glass in the rear deck, seat seams, and trunk/cargo area. Clean it in stages so you do not drive shards deeper into upholstery. Put on safety glasses, thick gloves, and sturdy shoes, and keep unprotected passengers out of the work area. If available, lay plastic sheeting over seats and the cargo floor before you start lifting pieces. Start with big fragments. Pick larger chunks from the window frame and rear deck and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong vacuum using a crevice tool. Follow a top-down route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk well, including the spare-tire compartment. After the first vacuum, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from fabric and corners; repeat until the tape comes back clean. Finish by wiping plastics with a slightly damp microfiber towel rather than scrubbing. If you have mobile rear glass replacement scheduled with Bang AutoGlass, clear loose debris around the opening so the bond area stays clean.
Confirm the Correct Rear Glass for Toyota Rav4 Prime: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Before you replace the rear window on a Toyota Rav4 Prime, confirm which back glass the vehicle needs. VIN validation or a parts lookup is the safest method because option differences change the glass. Start with the rear defroster: the replacement must include the correct heating grid and the proper terminal tabs so the factory connectors attach securely. Also verify antenna features. Many vehicles embed AM/FM, GPS, or cellular traces in the rear glass; if your reception relied on those lines, choose an antenna-equipped replacement. Tint matching matters as well. Rear glass may be clear, lightly tinted, or privacy glass with a darker factory shade. Matching tint supports a uniform look, better heat rejection, and local compliance. If your Toyota Rav4 Prime had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after installation. Finally, verify the certification stamp. Automotive glass includes DOT identification and AS markings (AS2/AS3 are common on rear/side glass and can indicate tinted variations). Correct markings and the part number help ensure proper curvature and tempered-glass performance. Bang AutoGlass verifies these details before mobile dispatch and backs every install with our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
A quality rear glass replacement starts with careful removal and prep for your Toyota Rav4 Prime. Bang AutoGlass covers the seats, rear deck, and cargo area, then removes trim, clips, and moldings needed to access the opening without scuffing interior panels. We clear tempered-glass fragments, manage rear defroster/antenna connectors, and cut the existing urethane with controlled tools so the vehicle aperture stays intact. Next we inspect the pinchweld-the metal bonding flange the urethane bonds to. Best practice is to remove most of the old urethane while leaving a thin, uniform base layer (about 1-2 mm) so new urethane bonds to cured urethane instead of bare metal. If we find scratches through paint, corrosion, or prior bodywork issues, we correct and prime/seal exposed metal because rust under the bond line is a common cause of leaks and adhesion loss. Finally, we dry-fit the replacement back glass for your Toyota Rav4 Prime, confirm spacers and molding condition, clean the frit and aperture, and apply the proper primers/activators with correct flash times. With surfaces ready, we set the glass with even pressure for a consistent perimeter seal-mobile, next-day rear window replacement backed by our lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Toyota Rav4 Prime: What Controls Safe Release
The difference between "installed" and "safe" after a Toyota Rav4 Prime rear window replacement is urethane curing. Auto glass urethane is a moisture-curing polyurethane adhesive, and each system includes Safe Drive-Away Time (SDAT) guidance tied to minimum bond strength. SDAT is controlled by the adhesive used, proper surface prep, bead size/shape, and environmental conditions like temperature and humidity. Cold or very dry air can slow cure; warm, humid conditions typically speed it up. Open-time limits also matter-urethane must be applied and the glass set within the specified window for proper wet-out and adhesion. Prep details directly affect the bond: clean, contaminant-free surfaces; correct primer/activator application; and required flash times. The urethane bead must be continuous and uniform so it compresses evenly around the perimeter, preventing thin spots that can leak or whistle. Exposed metal on the pinchweld must be protected and primed because corrosion under the bond line is a common long-term failure point. At Bang AutoGlass, most Toyota Rav4 Prime back glass replacements take about 30-45 minutes on site, then we require at least 1 hour before safe drive-away. Drive gently, avoid slamming doors, and skip automated car washes; we'll extend cure time if conditions warrant it, backed by our lifetime workmanship warranty and help with comprehensive coverage claims.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
Post-install checks turn a rear glass replacement on your Toyota Rav4 Prime into a dependable repair. First, verify features: rear defroster tabs should be seated securely, and connectors should be aligned and strain-relieved so hatch or trunk movement doesn't pull leads loose. If your Toyota Rav4 Prime uses in-glass antennas, those connections must be restored to avoid degraded AM/FM reception. A quick functional confirmation on site is the fastest way to catch a connection issue early. Next, confirm water and air sealing. Even spacing around the perimeter and a clean reveal line indicate proper set-down and molding alignment. A controlled perimeter water test helps confirm the urethane bond line is sealed, and a short road test (when practical) reproduces highway airflow to check for wind noise; a new whistle usually points to a small gap or mis-seated molding. Finally, keep records and follow care guidance. You should have documentation of the glass type installed (tint, defroster grid, antenna integration, and DOT/AS stamp) and a clear warranty record. Bang AutoGlass provides an invoice and backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time, avoid slamming doors right after service, and skip automated car washes for the first day to protect the fresh adhesive seal.
Services
Service Areas
Shattered Back Window on Toyota Rav4 Prime: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Toyota Rav4 Prime: Safety, Visibility, and Securing the Vehicle
If the rear window on your Toyota Rav4 Prime shatters, treat it as a safety and security issue until a professional rear window replacement is completed. If it breaks while driving, slow down, turn on hazard lights, and pull into a safe, well-lit area. Tempered back glass fractures into small cubes, but they can still cut skin and irritate eyes--avoid touching your face and keep children and pets away. With gloves and eye protection, remove only loose pieces that block visibility or could drop into the cabin. Next, protect the interior from weather and theft. Remove valuables and cover the opening with plastic sheeting or a heavy-duty bag, securing it with painter's tape or other low-tack tape. Do not slam doors or the hatch; pressure changes can dislodge remaining glass. Take photos for an insurance claim, since rear glass damage is commonly handled under comprehensive coverage. Bang AutoGlass makes Toyota Rav4 Prime back glass replacement straightforward with fully mobile service, often as soon as next day. Most installs take about 30-45 minutes on site, then the urethane requires at least 1 hour of cure time before safe drive-away. Every job is backed by our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A broken rear window means your Toyota Rav4 Prime likely has glass in the rear deck, seat seams, and trunk/cargo area. Clean it in stages so you do not drive shards deeper into upholstery. Put on safety glasses, thick gloves, and sturdy shoes, and keep unprotected passengers out of the work area. If available, lay plastic sheeting over seats and the cargo floor before you start lifting pieces. Start with big fragments. Pick larger chunks from the window frame and rear deck and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong vacuum using a crevice tool. Follow a top-down route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk well, including the spare-tire compartment. After the first vacuum, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from fabric and corners; repeat until the tape comes back clean. Finish by wiping plastics with a slightly damp microfiber towel rather than scrubbing. If you have mobile rear glass replacement scheduled with Bang AutoGlass, clear loose debris around the opening so the bond area stays clean.
Confirm the Correct Rear Glass for Toyota Rav4 Prime: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Before you replace the rear window on a Toyota Rav4 Prime, confirm which back glass the vehicle needs. VIN validation or a parts lookup is the safest method because option differences change the glass. Start with the rear defroster: the replacement must include the correct heating grid and the proper terminal tabs so the factory connectors attach securely. Also verify antenna features. Many vehicles embed AM/FM, GPS, or cellular traces in the rear glass; if your reception relied on those lines, choose an antenna-equipped replacement. Tint matching matters as well. Rear glass may be clear, lightly tinted, or privacy glass with a darker factory shade. Matching tint supports a uniform look, better heat rejection, and local compliance. If your Toyota Rav4 Prime had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after installation. Finally, verify the certification stamp. Automotive glass includes DOT identification and AS markings (AS2/AS3 are common on rear/side glass and can indicate tinted variations). Correct markings and the part number help ensure proper curvature and tempered-glass performance. Bang AutoGlass verifies these details before mobile dispatch and backs every install with our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
A quality rear glass replacement starts with careful removal and prep for your Toyota Rav4 Prime. Bang AutoGlass covers the seats, rear deck, and cargo area, then removes trim, clips, and moldings needed to access the opening without scuffing interior panels. We clear tempered-glass fragments, manage rear defroster/antenna connectors, and cut the existing urethane with controlled tools so the vehicle aperture stays intact. Next we inspect the pinchweld-the metal bonding flange the urethane bonds to. Best practice is to remove most of the old urethane while leaving a thin, uniform base layer (about 1-2 mm) so new urethane bonds to cured urethane instead of bare metal. If we find scratches through paint, corrosion, or prior bodywork issues, we correct and prime/seal exposed metal because rust under the bond line is a common cause of leaks and adhesion loss. Finally, we dry-fit the replacement back glass for your Toyota Rav4 Prime, confirm spacers and molding condition, clean the frit and aperture, and apply the proper primers/activators with correct flash times. With surfaces ready, we set the glass with even pressure for a consistent perimeter seal-mobile, next-day rear window replacement backed by our lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Toyota Rav4 Prime: What Controls Safe Release
The difference between "installed" and "safe" after a Toyota Rav4 Prime rear window replacement is urethane curing. Auto glass urethane is a moisture-curing polyurethane adhesive, and each system includes Safe Drive-Away Time (SDAT) guidance tied to minimum bond strength. SDAT is controlled by the adhesive used, proper surface prep, bead size/shape, and environmental conditions like temperature and humidity. Cold or very dry air can slow cure; warm, humid conditions typically speed it up. Open-time limits also matter-urethane must be applied and the glass set within the specified window for proper wet-out and adhesion. Prep details directly affect the bond: clean, contaminant-free surfaces; correct primer/activator application; and required flash times. The urethane bead must be continuous and uniform so it compresses evenly around the perimeter, preventing thin spots that can leak or whistle. Exposed metal on the pinchweld must be protected and primed because corrosion under the bond line is a common long-term failure point. At Bang AutoGlass, most Toyota Rav4 Prime back glass replacements take about 30-45 minutes on site, then we require at least 1 hour before safe drive-away. Drive gently, avoid slamming doors, and skip automated car washes; we'll extend cure time if conditions warrant it, backed by our lifetime workmanship warranty and help with comprehensive coverage claims.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
Post-install checks turn a rear glass replacement on your Toyota Rav4 Prime into a dependable repair. First, verify features: rear defroster tabs should be seated securely, and connectors should be aligned and strain-relieved so hatch or trunk movement doesn't pull leads loose. If your Toyota Rav4 Prime uses in-glass antennas, those connections must be restored to avoid degraded AM/FM reception. A quick functional confirmation on site is the fastest way to catch a connection issue early. Next, confirm water and air sealing. Even spacing around the perimeter and a clean reveal line indicate proper set-down and molding alignment. A controlled perimeter water test helps confirm the urethane bond line is sealed, and a short road test (when practical) reproduces highway airflow to check for wind noise; a new whistle usually points to a small gap or mis-seated molding. Finally, keep records and follow care guidance. You should have documentation of the glass type installed (tint, defroster grid, antenna integration, and DOT/AS stamp) and a clear warranty record. Bang AutoGlass provides an invoice and backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time, avoid slamming doors right after service, and skip automated car washes for the first day to protect the fresh adhesive seal.
Enjoy More Relevant Blogs
How Much Does Rear Glass Replacement Cost for Toyota Rav4 Prime? Pricing Factors, OEM vs Aftermarket, and Insurance Deductibles
Estimate Toyota Rav4 Prime rear glass replacement cost. Compare OEM vs aftermarket, labor factors, insurance deductibles, and ways to save. Request a quote.
How to Schedule Mobile Rear Glass Replacement for Toyota Rav4 Prime
Schedule mobile rear glass replacement for your Toyota Rav4 Prime in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Rear Glass Replacement for Toyota Rav4 Prime: What to Expect During Install and Aftercare
Rear glass replacement for Toyota Rav4 Prime: what happens during install, defroster and tint considerations, cure time, and aftercare to prevent leaks long-term.
Tempered Safety Rear Glass Replacement for Toyota Rav4 Prime: Understanding DOT Markings and FMVSS 205
Need Toyota Rav4 Prime rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Back Glass Replacement on Toyota Rav4 Prime: Defroster Tabs, Antenna Lines, and Connector Reattachment Basics
Back glass replacement on Toyota Rav4 Prime: defroster tabs, antenna lines, and connectors explained, plus install tips to avoid damage and rework safely.
OEM-Quality Rear Glass Replacement for Toyota Rav4 Prime: Defroster Grid and Tint-Match Checklist
OEM-quality rear glass replacement for Toyota Rav4 Prime: defroster grid and tint-match checklist, plus install tips to avoid callbacks—schedule service.
Rear Defroster Not Working on Toyota Rav4 Prime? When Rear Glass Replacement Makes More Sense Than Repair
Rear defroster not working on your Toyota Rav4 Prime? Learn common causes, when repair fails, and when rear glass replacement is the smarter fix for winter.
Post-Install Checks for Toyota Rav4 Prime: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Toyota Rav4 Prime: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
How Long Does Rear Glass Replacement Take on Toyota Rav4 Prime? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How long is Toyota Rav4 Prime rear glass replacement? Get install time, urethane cure guidelines, and drive-away timing after service. Plan your visit today.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm