Services
Service Areas
How Much Does ADAS Calibration Cost for Volkswagen ID.2? What Drives Pricing and What Insurance Typically Covers
How Much Does ADAS Calibration Cost for Volkswagen ID.2 in 2026? Typical Price Range and What’s Included
ADAS calibration cost for a Volkswagen ID.2 is usually quoted by the number of calibrations required, not a single flat fee. Model year, trim, and safety options determine which sensors are present, so a helpful benchmark is roughly $200–$550 per calibration operation. In many areas, a single camera calibration is often billed around $350–$500, and totals increase when the repair also requires front radar or other sensors to be recalibrated. When you compare quotes, confirm what’s included. A proper ADAS calibration should start with a pre-repair scan to capture DTCs, followed by OEM prerequisite checks like tire pressure, verified ride height, clean sensor windows, and the correct lighting and setup. The technician then completes the required static target routine or dynamic drive cycle, validates successful completion, and finishes with a post-scan and saved report. Those scan results are valuable for quality control and are commonly needed for insurance reimbursement when calibration is tied to a covered claim. Bang AutoGlass keeps the process simple: mobile windshield replacement typically takes 30–45 minutes, then at least one hour of safe-drive-away cure time. If your Volkswagen ID.2 needs calibration, we help schedule it quickly—often next day—with a lifetime workmanship warranty.
Static vs Dynamic ADAS Calibration for Volkswagen ID.2: Key Differences, Time Required, and Cost
On a Volkswagen ID.2, the terms “static” and “dynamic” ADAS calibration describe the OEM-approved method the vehicle uses to re-establish camera and radar alignment after a repair. Dynamic calibration is performed on the road, where your Volkswagen ID.2 completes a defined drive cycle so the camera can lock onto lane markings and other cues. Static calibration is performed with the vehicle stationary, using measured target boards placed to exact specifications. Both methods can take an hour or more once the car is ready, but the risks for delays are different. Dynamic calibration depends on safe, consistent road conditions; rain, heavy traffic, or faded lane lines can prevent completion. Static calibration depends on the shop environment; the floor must be within level tolerance, lighting must be consistent, and target distances must be measured precisely. In either case, prerequisites matter: clear DTCs, correct tire pressure, verified ride height, and clean sensor surfaces. Pricing generally tracks equipment and process control, so static target-based calibrations often cost more than dynamic routines. Some Volkswagen ID.2 versions require both steps, so confirm the VIN-specific procedure before quoting.
Which Volkswagen ID.2 ADAS Features Need Calibration: Windshield Camera, Radar, Blind Spot, and 360 Camera Systems
Calibration requirements on a Volkswagen ID.2 depend on which sensors were affected, but windshield replacement most often triggers calibration of the forward-facing camera mounted at the glass. Automaker procedures commonly require a calibration (often called a “relearn” or service setup) whenever the camera is removed, reinstalled, replaced, or whenever the windshield is replaced. Even a minor change in camera position or windshield optics can alter lane recognition and distance estimation, influencing lane centering, forward collision warning, and automatic emergency braking. From there, the list can expand: many Volkswagen ID.2 packages include front radar for adaptive cruise control and collision mitigation, rear radar for blind spot monitoring and rear cross-traffic alert, and additional cameras for 360-degree views and parking assistance. Calibrations may also be required after bumper removal, mirror replacement, sensor bracket repairs, wheel alignment, or suspension work that changes ride height. Because triggers vary by model year and trim, the reliable method is to follow the VIN-specific OEM workflow. A pre-scan, completed calibration routine, and post-scan with saved reports provide proof the system is ready for the road. You should receive a calibration completion report and itemized invoice for your records. Bang AutoGlass follows that documentation-first process for every Volkswagen ID.2.
What Drives Volkswagen ID.2 ADAS Calibration Pricing: Pre-Scan/Post-Scan, Targets, Labor, and Shop Equipment
ADAS calibration cost for a Volkswagen ID.2 varies because shops are following a VIN-driven OEM checklist, not running a generic reset. One major cost driver is scan documentation: the pre-scan captures existing DTCs and confirms the vehicle is eligible to calibrate, and the post-scan proves the job finished without new faults. Those reports are often required for insurance reimbursement and help protect your repair history. Method and environment matter next. Static calibration is target-based and depends on accurate measurements, consistent lighting, and a level floor within OEM tolerance. That requires dedicated space plus frames, targets, compatible scan tools, and software access-investments that are built into pricing. Dynamic calibration uses an OEM road drive cycle, which can reduce bay constraints but adds drive time and can fail if lane markings, traffic, or weather don't meet conditions. Finally, the systems on your Volkswagen ID.2 affect labor time. Many vehicles need more than a windshield camera calibration; front radar, blind-spot sensors, and surround-view cameras may also be involved. Add bracket inspection, alignment or ride-height verification, and a completion report, and you can see why the most accurate quote is tied to your VIN and repair scenario.
Dealer vs Independent Shop vs Mobile ADAS Calibration for Volkswagen ID.2: Cost Comparison and What You Get
To choose between a dealer, an independent shop, or mobile ADAS calibration for a Volkswagen ID.2, compare process quality and documentation first. Dealers typically have manufacturer tools and service information, which can be useful for new model years, but labor rates and appointment delays often increase the final bill. A reputable independent calibration center can be a strong alternative when it follows the same VIN-specific OEM steps. Confirm they complete pre-scan/post-scan, verify prerequisites (tire pressure, ride height, clean sensor areas, and no active faults), and issue a calibration completion report. That paperwork is what insurers and warranties often rely on if questions come up later. Mobile calibration is convenient, especially when coordinated with mobile windshield replacement, but it still has to meet OEM requirements. Many static calibrations require controlled lighting, measured distances, and level ground for target placement, while dynamic calibrations require a prescribed road drive cycle. A trustworthy provider will bring a compliant setup or route the vehicle to the right environment when needed. Bang AutoGlass comes to you for mobile windshield replacement (typically 30-45 minutes) with at least one hour of safe-drive-away cure time, and we help coordinate any required Volkswagen ID.2 calibration backed by a lifetime workmanship warranty.
Does Insurance Cover Volkswagen ID.2 ADAS Calibration? Comprehensive vs Collision, Deductibles, and Documentation Tips
Insurance coverage for Volkswagen ID.2 ADAS calibration usually depends on (1) whether the loss is comprehensive or collision and (2) whether calibration is documented as a necessary step of a covered repair. Rock strikes, debris, vandalism, and other non-collision glass losses are commonly handled under comprehensive coverage, while crash-related damage is typically processed under collision. Your deductible still applies based on your policy-some plans waive deductibles for chip repair, but windshield replacement and calibration generally follow your claim terms. Approval is easiest when paperwork ties calibration directly to OEM requirements. Provide pre-scan/post-scan results, a calibration completion report (static and/or dynamic), and an itemized invoice. If asked "why is this needed," the answer is that driver-assist features-lane keeping, forward collision warning, automatic emergency braking, adaptive cruise control, blind spot monitoring, and 360 degrees camera systems-depend on precise sensor alignment, and manufacturers frequently require scanning and calibration after windshield replacement or related repairs. To avoid delays, confirm claim type and deductible up front, keep photos of damage, and ensure invoices list the Volkswagen ID.2 VIN plus the specific calibrations performed. Save scan and calibration reports as PDFs for fast upload. Bang AutoGlass accepts all insurance companies when you carry comprehensive coverage and provides the documentation that supports reimbursement.
Services
Service Areas
How Much Does ADAS Calibration Cost for Volkswagen ID.2? What Drives Pricing and What Insurance Typically Covers
How Much Does ADAS Calibration Cost for Volkswagen ID.2 in 2026? Typical Price Range and What’s Included
ADAS calibration cost for a Volkswagen ID.2 is usually quoted by the number of calibrations required, not a single flat fee. Model year, trim, and safety options determine which sensors are present, so a helpful benchmark is roughly $200–$550 per calibration operation. In many areas, a single camera calibration is often billed around $350–$500, and totals increase when the repair also requires front radar or other sensors to be recalibrated. When you compare quotes, confirm what’s included. A proper ADAS calibration should start with a pre-repair scan to capture DTCs, followed by OEM prerequisite checks like tire pressure, verified ride height, clean sensor windows, and the correct lighting and setup. The technician then completes the required static target routine or dynamic drive cycle, validates successful completion, and finishes with a post-scan and saved report. Those scan results are valuable for quality control and are commonly needed for insurance reimbursement when calibration is tied to a covered claim. Bang AutoGlass keeps the process simple: mobile windshield replacement typically takes 30–45 minutes, then at least one hour of safe-drive-away cure time. If your Volkswagen ID.2 needs calibration, we help schedule it quickly—often next day—with a lifetime workmanship warranty.
Static vs Dynamic ADAS Calibration for Volkswagen ID.2: Key Differences, Time Required, and Cost
On a Volkswagen ID.2, the terms “static” and “dynamic” ADAS calibration describe the OEM-approved method the vehicle uses to re-establish camera and radar alignment after a repair. Dynamic calibration is performed on the road, where your Volkswagen ID.2 completes a defined drive cycle so the camera can lock onto lane markings and other cues. Static calibration is performed with the vehicle stationary, using measured target boards placed to exact specifications. Both methods can take an hour or more once the car is ready, but the risks for delays are different. Dynamic calibration depends on safe, consistent road conditions; rain, heavy traffic, or faded lane lines can prevent completion. Static calibration depends on the shop environment; the floor must be within level tolerance, lighting must be consistent, and target distances must be measured precisely. In either case, prerequisites matter: clear DTCs, correct tire pressure, verified ride height, and clean sensor surfaces. Pricing generally tracks equipment and process control, so static target-based calibrations often cost more than dynamic routines. Some Volkswagen ID.2 versions require both steps, so confirm the VIN-specific procedure before quoting.
Which Volkswagen ID.2 ADAS Features Need Calibration: Windshield Camera, Radar, Blind Spot, and 360 Camera Systems
Calibration requirements on a Volkswagen ID.2 depend on which sensors were affected, but windshield replacement most often triggers calibration of the forward-facing camera mounted at the glass. Automaker procedures commonly require a calibration (often called a “relearn” or service setup) whenever the camera is removed, reinstalled, replaced, or whenever the windshield is replaced. Even a minor change in camera position or windshield optics can alter lane recognition and distance estimation, influencing lane centering, forward collision warning, and automatic emergency braking. From there, the list can expand: many Volkswagen ID.2 packages include front radar for adaptive cruise control and collision mitigation, rear radar for blind spot monitoring and rear cross-traffic alert, and additional cameras for 360-degree views and parking assistance. Calibrations may also be required after bumper removal, mirror replacement, sensor bracket repairs, wheel alignment, or suspension work that changes ride height. Because triggers vary by model year and trim, the reliable method is to follow the VIN-specific OEM workflow. A pre-scan, completed calibration routine, and post-scan with saved reports provide proof the system is ready for the road. You should receive a calibration completion report and itemized invoice for your records. Bang AutoGlass follows that documentation-first process for every Volkswagen ID.2.
What Drives Volkswagen ID.2 ADAS Calibration Pricing: Pre-Scan/Post-Scan, Targets, Labor, and Shop Equipment
ADAS calibration cost for a Volkswagen ID.2 varies because shops are following a VIN-driven OEM checklist, not running a generic reset. One major cost driver is scan documentation: the pre-scan captures existing DTCs and confirms the vehicle is eligible to calibrate, and the post-scan proves the job finished without new faults. Those reports are often required for insurance reimbursement and help protect your repair history. Method and environment matter next. Static calibration is target-based and depends on accurate measurements, consistent lighting, and a level floor within OEM tolerance. That requires dedicated space plus frames, targets, compatible scan tools, and software access-investments that are built into pricing. Dynamic calibration uses an OEM road drive cycle, which can reduce bay constraints but adds drive time and can fail if lane markings, traffic, or weather don't meet conditions. Finally, the systems on your Volkswagen ID.2 affect labor time. Many vehicles need more than a windshield camera calibration; front radar, blind-spot sensors, and surround-view cameras may also be involved. Add bracket inspection, alignment or ride-height verification, and a completion report, and you can see why the most accurate quote is tied to your VIN and repair scenario.
Dealer vs Independent Shop vs Mobile ADAS Calibration for Volkswagen ID.2: Cost Comparison and What You Get
To choose between a dealer, an independent shop, or mobile ADAS calibration for a Volkswagen ID.2, compare process quality and documentation first. Dealers typically have manufacturer tools and service information, which can be useful for new model years, but labor rates and appointment delays often increase the final bill. A reputable independent calibration center can be a strong alternative when it follows the same VIN-specific OEM steps. Confirm they complete pre-scan/post-scan, verify prerequisites (tire pressure, ride height, clean sensor areas, and no active faults), and issue a calibration completion report. That paperwork is what insurers and warranties often rely on if questions come up later. Mobile calibration is convenient, especially when coordinated with mobile windshield replacement, but it still has to meet OEM requirements. Many static calibrations require controlled lighting, measured distances, and level ground for target placement, while dynamic calibrations require a prescribed road drive cycle. A trustworthy provider will bring a compliant setup or route the vehicle to the right environment when needed. Bang AutoGlass comes to you for mobile windshield replacement (typically 30-45 minutes) with at least one hour of safe-drive-away cure time, and we help coordinate any required Volkswagen ID.2 calibration backed by a lifetime workmanship warranty.
Does Insurance Cover Volkswagen ID.2 ADAS Calibration? Comprehensive vs Collision, Deductibles, and Documentation Tips
Insurance coverage for Volkswagen ID.2 ADAS calibration usually depends on (1) whether the loss is comprehensive or collision and (2) whether calibration is documented as a necessary step of a covered repair. Rock strikes, debris, vandalism, and other non-collision glass losses are commonly handled under comprehensive coverage, while crash-related damage is typically processed under collision. Your deductible still applies based on your policy-some plans waive deductibles for chip repair, but windshield replacement and calibration generally follow your claim terms. Approval is easiest when paperwork ties calibration directly to OEM requirements. Provide pre-scan/post-scan results, a calibration completion report (static and/or dynamic), and an itemized invoice. If asked "why is this needed," the answer is that driver-assist features-lane keeping, forward collision warning, automatic emergency braking, adaptive cruise control, blind spot monitoring, and 360 degrees camera systems-depend on precise sensor alignment, and manufacturers frequently require scanning and calibration after windshield replacement or related repairs. To avoid delays, confirm claim type and deductible up front, keep photos of damage, and ensure invoices list the Volkswagen ID.2 VIN plus the specific calibrations performed. Save scan and calibration reports as PDFs for fast upload. Bang AutoGlass accepts all insurance companies when you carry comprehensive coverage and provides the documentation that supports reimbursement.
Services
Service Areas
How Much Does ADAS Calibration Cost for Volkswagen ID.2? What Drives Pricing and What Insurance Typically Covers
How Much Does ADAS Calibration Cost for Volkswagen ID.2 in 2026? Typical Price Range and What’s Included
ADAS calibration cost for a Volkswagen ID.2 is usually quoted by the number of calibrations required, not a single flat fee. Model year, trim, and safety options determine which sensors are present, so a helpful benchmark is roughly $200–$550 per calibration operation. In many areas, a single camera calibration is often billed around $350–$500, and totals increase when the repair also requires front radar or other sensors to be recalibrated. When you compare quotes, confirm what’s included. A proper ADAS calibration should start with a pre-repair scan to capture DTCs, followed by OEM prerequisite checks like tire pressure, verified ride height, clean sensor windows, and the correct lighting and setup. The technician then completes the required static target routine or dynamic drive cycle, validates successful completion, and finishes with a post-scan and saved report. Those scan results are valuable for quality control and are commonly needed for insurance reimbursement when calibration is tied to a covered claim. Bang AutoGlass keeps the process simple: mobile windshield replacement typically takes 30–45 minutes, then at least one hour of safe-drive-away cure time. If your Volkswagen ID.2 needs calibration, we help schedule it quickly—often next day—with a lifetime workmanship warranty.
Static vs Dynamic ADAS Calibration for Volkswagen ID.2: Key Differences, Time Required, and Cost
On a Volkswagen ID.2, the terms “static” and “dynamic” ADAS calibration describe the OEM-approved method the vehicle uses to re-establish camera and radar alignment after a repair. Dynamic calibration is performed on the road, where your Volkswagen ID.2 completes a defined drive cycle so the camera can lock onto lane markings and other cues. Static calibration is performed with the vehicle stationary, using measured target boards placed to exact specifications. Both methods can take an hour or more once the car is ready, but the risks for delays are different. Dynamic calibration depends on safe, consistent road conditions; rain, heavy traffic, or faded lane lines can prevent completion. Static calibration depends on the shop environment; the floor must be within level tolerance, lighting must be consistent, and target distances must be measured precisely. In either case, prerequisites matter: clear DTCs, correct tire pressure, verified ride height, and clean sensor surfaces. Pricing generally tracks equipment and process control, so static target-based calibrations often cost more than dynamic routines. Some Volkswagen ID.2 versions require both steps, so confirm the VIN-specific procedure before quoting.
Which Volkswagen ID.2 ADAS Features Need Calibration: Windshield Camera, Radar, Blind Spot, and 360 Camera Systems
Calibration requirements on a Volkswagen ID.2 depend on which sensors were affected, but windshield replacement most often triggers calibration of the forward-facing camera mounted at the glass. Automaker procedures commonly require a calibration (often called a “relearn” or service setup) whenever the camera is removed, reinstalled, replaced, or whenever the windshield is replaced. Even a minor change in camera position or windshield optics can alter lane recognition and distance estimation, influencing lane centering, forward collision warning, and automatic emergency braking. From there, the list can expand: many Volkswagen ID.2 packages include front radar for adaptive cruise control and collision mitigation, rear radar for blind spot monitoring and rear cross-traffic alert, and additional cameras for 360-degree views and parking assistance. Calibrations may also be required after bumper removal, mirror replacement, sensor bracket repairs, wheel alignment, or suspension work that changes ride height. Because triggers vary by model year and trim, the reliable method is to follow the VIN-specific OEM workflow. A pre-scan, completed calibration routine, and post-scan with saved reports provide proof the system is ready for the road. You should receive a calibration completion report and itemized invoice for your records. Bang AutoGlass follows that documentation-first process for every Volkswagen ID.2.
What Drives Volkswagen ID.2 ADAS Calibration Pricing: Pre-Scan/Post-Scan, Targets, Labor, and Shop Equipment
ADAS calibration cost for a Volkswagen ID.2 varies because shops are following a VIN-driven OEM checklist, not running a generic reset. One major cost driver is scan documentation: the pre-scan captures existing DTCs and confirms the vehicle is eligible to calibrate, and the post-scan proves the job finished without new faults. Those reports are often required for insurance reimbursement and help protect your repair history. Method and environment matter next. Static calibration is target-based and depends on accurate measurements, consistent lighting, and a level floor within OEM tolerance. That requires dedicated space plus frames, targets, compatible scan tools, and software access-investments that are built into pricing. Dynamic calibration uses an OEM road drive cycle, which can reduce bay constraints but adds drive time and can fail if lane markings, traffic, or weather don't meet conditions. Finally, the systems on your Volkswagen ID.2 affect labor time. Many vehicles need more than a windshield camera calibration; front radar, blind-spot sensors, and surround-view cameras may also be involved. Add bracket inspection, alignment or ride-height verification, and a completion report, and you can see why the most accurate quote is tied to your VIN and repair scenario.
Dealer vs Independent Shop vs Mobile ADAS Calibration for Volkswagen ID.2: Cost Comparison and What You Get
To choose between a dealer, an independent shop, or mobile ADAS calibration for a Volkswagen ID.2, compare process quality and documentation first. Dealers typically have manufacturer tools and service information, which can be useful for new model years, but labor rates and appointment delays often increase the final bill. A reputable independent calibration center can be a strong alternative when it follows the same VIN-specific OEM steps. Confirm they complete pre-scan/post-scan, verify prerequisites (tire pressure, ride height, clean sensor areas, and no active faults), and issue a calibration completion report. That paperwork is what insurers and warranties often rely on if questions come up later. Mobile calibration is convenient, especially when coordinated with mobile windshield replacement, but it still has to meet OEM requirements. Many static calibrations require controlled lighting, measured distances, and level ground for target placement, while dynamic calibrations require a prescribed road drive cycle. A trustworthy provider will bring a compliant setup or route the vehicle to the right environment when needed. Bang AutoGlass comes to you for mobile windshield replacement (typically 30-45 minutes) with at least one hour of safe-drive-away cure time, and we help coordinate any required Volkswagen ID.2 calibration backed by a lifetime workmanship warranty.
Does Insurance Cover Volkswagen ID.2 ADAS Calibration? Comprehensive vs Collision, Deductibles, and Documentation Tips
Insurance coverage for Volkswagen ID.2 ADAS calibration usually depends on (1) whether the loss is comprehensive or collision and (2) whether calibration is documented as a necessary step of a covered repair. Rock strikes, debris, vandalism, and other non-collision glass losses are commonly handled under comprehensive coverage, while crash-related damage is typically processed under collision. Your deductible still applies based on your policy-some plans waive deductibles for chip repair, but windshield replacement and calibration generally follow your claim terms. Approval is easiest when paperwork ties calibration directly to OEM requirements. Provide pre-scan/post-scan results, a calibration completion report (static and/or dynamic), and an itemized invoice. If asked "why is this needed," the answer is that driver-assist features-lane keeping, forward collision warning, automatic emergency braking, adaptive cruise control, blind spot monitoring, and 360 degrees camera systems-depend on precise sensor alignment, and manufacturers frequently require scanning and calibration after windshield replacement or related repairs. To avoid delays, confirm claim type and deductible up front, keep photos of damage, and ensure invoices list the Volkswagen ID.2 VIN plus the specific calibrations performed. Save scan and calibration reports as PDFs for fast upload. Bang AutoGlass accepts all insurance companies when you carry comprehensive coverage and provides the documentation that supports reimbursement.
Enjoy More Relevant Blogs
How to Schedule ADAS Calibration for Volkswagen ID.2 After Windshield Replacement
Schedule ADAS calibration for Volkswagen ID.2 after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
Mobile ADAS Calibration for Volkswagen ID.2: What to Expect On-Site and Why Setup Matters
Mobile ADAS calibration for Volkswagen ID.2: what to expect on-site, space and lighting needs, and why setup and verification matter after repairs today.
Camera Calibration for Volkswagen ID.2: Lane Assist and Forward Collision Accuracy Explained
Need camera calibration for your Volkswagen ID.2? See how calibration affects lane assist and forward collision accuracy after windshield service or repairs.
Do You Need ADAS Calibration for Volkswagen ID.2 After a Wheel Alignment, Suspension Work, or a Minor Collision?
Do you need ADAS calibration for a Volkswagen ID.2 after alignment, suspension work, or a minor collision? Signs, timelines, safety risks, and costs today.
ADAS Calibration Checklist for Volkswagen ID.2: Documentation, Verification, and Final Safety Checks
ADAS calibration checklist for Volkswagen ID.2: documentation to request, scans to verify, and safety checks that confirm cameras and sensors are set right.
ADAS Warning Lights on Volkswagen ID.2: When Calibration Is the Fix and When It’s Not
ADAS warning lights on your Volkswagen ID.2? Learn when calibration fixes lane assist or AEB issues, when it will not, and what to check next. Schedule help.
Pre- and Post-Calibration Scans for Volkswagen ID.2: Proving Systems Are Set Correctly
Pre- and post-calibration scans for Volkswagen ID.2: see why scans matter, what they verify, and how reports prove ADAS systems are set correctly after service.
OEM Calibration Requirements for Volkswagen ID.2: How to Confirm What Must Be Calibrated
OEM calibration requirements for Volkswagen ID.2: how to confirm what must be calibrated after repairs, what triggers recalibration, and what proof to ask for.
Static vs Dynamic ADAS Calibration for Volkswagen ID.2: What the Difference Means
Static vs dynamic ADAS calibration for Volkswagen ID.2: key differences, when each is required, how long it takes, and what affects accuracy for safety.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm