Services
Service Areas
ADAS Warning Lights on Acura Mdx: What the Icons and Messages Commonly Indicate
ADAS warning lights on a Acura Mdx are a status signal from the driver-assist system: a feature is limited, unavailable, or requesting service. The icon hints at what’s affected—a car between lane lines for Lane Keep Assist/Lane Departure Warning, a crash/impact graphic for Forward Collision Warning or Automatic Emergency Braking, and a cruise/speedometer symbol for Adaptive Cruise Control. Many clusters also display “Camera Obscured,” “Front Radar Blocked,” “ACC Unavailable,” or “Driver Assist Limited” when sensors can’t see well enough to pass their self-check. Rule out simple visibility problems first. Clean the windshield inside and out at the camera window near the rearview mirror; haze, fogging, frost, and wiper streaks can reduce contrast and disable lane tracking. Confirm washer spray and wiper blades clear without smearing. Then wipe the front emblem/radar cover and remove bugs, mud, snow, or ice. In heavy rain, glare, fog, or blowing snow, brief dropouts can be normal. If the warning started after a rock chip, crack, windshield replacement, or a front-end bump, calibration may be required. Bang AutoGlass offers mobile windshield replacement as soon as next day, 30–45 minute installs, at least 1 hour safe drive-away time, insurance support, and a lifetime workmanship warranty.
When Calibration Is the Fix for Acura Mdx: Post-Windshield Replacement and Sensor Alignment Triggers
On a Acura Mdx, calibration is often the right fix when ADAS warnings appear right after a windshield replacement or work that disturbed the forward camera or front radar. Aiming tolerances are tight, and the software expects sensors to sit at a precise angle and position. If the wrong windshield is installed, a camera bracket shifts, or a radar mount moves during bumper work, the vehicle may disable features like Lane Keep Assist or Adaptive Cruise Control and show messages such as “Calibration Required,” “ACC Unavailable,” or “Driver Assist Limited.” Calibration may also be required after changes that alter vehicle geometry: collision repair, bumper removal, wheel alignment, suspension or ride-height work, steering service, or non-OEM tire sizing. Even light contact can bend a radar bracket enough to fail a self-check. Follow OEM sequence. Verify the correct windshield for the Acura Mdx, confirm the camera mount and radar cover are clean and intact, run a diagnostic pre-scan, complete the required static and/or dynamic procedure, then do a post-scan to confirm systems re-enable. Bang AutoGlass provides mobile replacement as soon as next day (30–45 minutes plus at least 1 hour safe drive-away time) and a lifetime workmanship warranty.
When It’s Not Calibration on Acura Mdx: Obstructions, Damage, Voltage, Wiring, and Module Faults
On a Acura Mdx, an ADAS warning light does not automatically mean calibration is needed. Many systems pause whenever sensor input is unreliable. Weather and road conditions are common causes: heavy rain, snow, fog, glare, or road spray can reduce camera contrast and prevent tracking of lane markings or vehicles, leading to “Camera Obscured” or “Driver Assist Limited.” Features often return once visibility improves. Obstructions and add-ons can create the same symptoms. Dashcams, toll tags, stickers, and poorly placed tint near the camera window can block the forward view. Up front, a cracked, misaligned, or painted radar cover/emblem can interrupt the signal and trigger “Front Radar Blocked” or “ACC Unavailable.” Electrical stability matters, too: a weak 12-volt battery or recent battery disconnect can set low-voltage or communication faults that take modules offline. If warnings persist after cleaning, treat it as diagnostics. A DTC scan helps distinguish a blocked sensor from fuse, ground, connector, corrosion, harness, camera/radar unit, or software issues. If the warning began after windshield damage, replacement, or a front-end impact, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Acura Mdx: Reading DTCs, Root-Cause Checks, and OEM Procedures
When ADAS warning lights appear on a Acura Mdx, the quickest route to a correct fix is a structured diagnostic process guided by scan results and OEM procedures. Messages indicate a limitation, not the underlying fault. That is why manufacturers recommend pre- and post-repair scanning whenever the windshield camera, front radar, or related steering/braking inputs have been disturbed—often after windshield replacement, bumper removal, collision repair, alignment changes, suspension work, or low-voltage events. Begin with a complete pre-scan (health check). Pull DTCs from all relevant modules because ADAS depends on ABS, steering angle, yaw/acceleration sensors, and network communications. Save code status and freeze-frame details before clearing anything. Then follow OEM root-cause checks: confirm battery/charging stability, inspect fuses and grounds, and examine connectors and harnesses at the camera and radar for looseness, corrosion, or pin-fit issues. Verify correct windshield specification, an intact camera bracket, clean viewing zones, and an undamaged radar cover aligned correctly. Confirm baseline conditions that affect aiming and eligibility—tire size/pressure, ride height, and alignment within specification. After repairs and any required calibration/initialization, run a post-scan to verify related DTCs are cleared and do not return. Bang AutoGlass offers mobile next-day service and can coordinate OEM calibration for your Acura Mdx.
Static vs Dynamic ADAS Calibration for Acura Mdx: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both return your Acura Mdx to OEM aiming specs, but they work differently and have strict prerequisites. Static calibration is done with the vehicle stationary in a controlled bay using OEM targets, measurements, and a scan tool to start the routine. Success typically requires a level floor, precise target distance/height, consistent lighting, correct tire pressures and tire size, normal ride height, and no active DTCs that would block the procedure. Dynamic calibration is completed on the road. The technician puts the system in learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, time or distance requirements, clear lane markings, and good visibility. Weather, traffic, construction zones, glare, or inconsistent lane paint can prevent learning and trigger “calibration incomplete” or “system unavailable” messages. Many Acura Mdx platforms require static, dynamic, or a dual process depending on what was disturbed (camera vs radar), and some also require steering angle sensor initialization. Calibration is not a reset: if alignment is out of spec, voltage is unstable, or the camera/radar area is obstructed, the warning may return even after an attempted routine. Bang AutoGlass offers mobile next-day windshield replacement and can help you plan the required OEM calibration.
Proving the Repair Worked on Acura Mdx: Post-Scan, Verification Drive, and Documentation
After ADAS-related work on a Acura Mdx, a warning light turning off is helpful, but proper closeout requires proof. Begin with a post-repair diagnostic scan across all relevant modules to confirm ADAS-related DTCs are cleared and no new communication, camera, or radar faults are present. If calibration or initialization was performed, retain the completion report showing which routines ran (camera, radar, steering angle sensor as applicable) and that each finished successfully. Next, follow OEM guidance for functional validation. When required, complete a verification drive to confirm lane keep assist stays available, adaptive cruise control engages and holds, and forward collision warning operates normally without “system limited” messages. Also check practical items that affect performance: the windshield camera zone is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare in the camera’s view. Finally, keep documentation organized—pre-scan and post-scan results, OEM procedure references, calibration reports, and road-test notes—to support insurance reimbursement and reduce disputes later. Bang AutoGlass makes the glass portion simple with mobile, as-soon-as-next-day service; most installs take 30–45 minutes plus at least 1 hour of safe drive-away time, and workmanship is backed by a lifetime warranty.
Services
Service Areas
ADAS Warning Lights on Acura Mdx: What the Icons and Messages Commonly Indicate
ADAS warning lights on a Acura Mdx are a status signal from the driver-assist system: a feature is limited, unavailable, or requesting service. The icon hints at what’s affected—a car between lane lines for Lane Keep Assist/Lane Departure Warning, a crash/impact graphic for Forward Collision Warning or Automatic Emergency Braking, and a cruise/speedometer symbol for Adaptive Cruise Control. Many clusters also display “Camera Obscured,” “Front Radar Blocked,” “ACC Unavailable,” or “Driver Assist Limited” when sensors can’t see well enough to pass their self-check. Rule out simple visibility problems first. Clean the windshield inside and out at the camera window near the rearview mirror; haze, fogging, frost, and wiper streaks can reduce contrast and disable lane tracking. Confirm washer spray and wiper blades clear without smearing. Then wipe the front emblem/radar cover and remove bugs, mud, snow, or ice. In heavy rain, glare, fog, or blowing snow, brief dropouts can be normal. If the warning started after a rock chip, crack, windshield replacement, or a front-end bump, calibration may be required. Bang AutoGlass offers mobile windshield replacement as soon as next day, 30–45 minute installs, at least 1 hour safe drive-away time, insurance support, and a lifetime workmanship warranty.
When Calibration Is the Fix for Acura Mdx: Post-Windshield Replacement and Sensor Alignment Triggers
On a Acura Mdx, calibration is often the right fix when ADAS warnings appear right after a windshield replacement or work that disturbed the forward camera or front radar. Aiming tolerances are tight, and the software expects sensors to sit at a precise angle and position. If the wrong windshield is installed, a camera bracket shifts, or a radar mount moves during bumper work, the vehicle may disable features like Lane Keep Assist or Adaptive Cruise Control and show messages such as “Calibration Required,” “ACC Unavailable,” or “Driver Assist Limited.” Calibration may also be required after changes that alter vehicle geometry: collision repair, bumper removal, wheel alignment, suspension or ride-height work, steering service, or non-OEM tire sizing. Even light contact can bend a radar bracket enough to fail a self-check. Follow OEM sequence. Verify the correct windshield for the Acura Mdx, confirm the camera mount and radar cover are clean and intact, run a diagnostic pre-scan, complete the required static and/or dynamic procedure, then do a post-scan to confirm systems re-enable. Bang AutoGlass provides mobile replacement as soon as next day (30–45 minutes plus at least 1 hour safe drive-away time) and a lifetime workmanship warranty.
When It’s Not Calibration on Acura Mdx: Obstructions, Damage, Voltage, Wiring, and Module Faults
On a Acura Mdx, an ADAS warning light does not automatically mean calibration is needed. Many systems pause whenever sensor input is unreliable. Weather and road conditions are common causes: heavy rain, snow, fog, glare, or road spray can reduce camera contrast and prevent tracking of lane markings or vehicles, leading to “Camera Obscured” or “Driver Assist Limited.” Features often return once visibility improves. Obstructions and add-ons can create the same symptoms. Dashcams, toll tags, stickers, and poorly placed tint near the camera window can block the forward view. Up front, a cracked, misaligned, or painted radar cover/emblem can interrupt the signal and trigger “Front Radar Blocked” or “ACC Unavailable.” Electrical stability matters, too: a weak 12-volt battery or recent battery disconnect can set low-voltage or communication faults that take modules offline. If warnings persist after cleaning, treat it as diagnostics. A DTC scan helps distinguish a blocked sensor from fuse, ground, connector, corrosion, harness, camera/radar unit, or software issues. If the warning began after windshield damage, replacement, or a front-end impact, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Acura Mdx: Reading DTCs, Root-Cause Checks, and OEM Procedures
When ADAS warning lights appear on a Acura Mdx, the quickest route to a correct fix is a structured diagnostic process guided by scan results and OEM procedures. Messages indicate a limitation, not the underlying fault. That is why manufacturers recommend pre- and post-repair scanning whenever the windshield camera, front radar, or related steering/braking inputs have been disturbed—often after windshield replacement, bumper removal, collision repair, alignment changes, suspension work, or low-voltage events. Begin with a complete pre-scan (health check). Pull DTCs from all relevant modules because ADAS depends on ABS, steering angle, yaw/acceleration sensors, and network communications. Save code status and freeze-frame details before clearing anything. Then follow OEM root-cause checks: confirm battery/charging stability, inspect fuses and grounds, and examine connectors and harnesses at the camera and radar for looseness, corrosion, or pin-fit issues. Verify correct windshield specification, an intact camera bracket, clean viewing zones, and an undamaged radar cover aligned correctly. Confirm baseline conditions that affect aiming and eligibility—tire size/pressure, ride height, and alignment within specification. After repairs and any required calibration/initialization, run a post-scan to verify related DTCs are cleared and do not return. Bang AutoGlass offers mobile next-day service and can coordinate OEM calibration for your Acura Mdx.
Static vs Dynamic ADAS Calibration for Acura Mdx: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both return your Acura Mdx to OEM aiming specs, but they work differently and have strict prerequisites. Static calibration is done with the vehicle stationary in a controlled bay using OEM targets, measurements, and a scan tool to start the routine. Success typically requires a level floor, precise target distance/height, consistent lighting, correct tire pressures and tire size, normal ride height, and no active DTCs that would block the procedure. Dynamic calibration is completed on the road. The technician puts the system in learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, time or distance requirements, clear lane markings, and good visibility. Weather, traffic, construction zones, glare, or inconsistent lane paint can prevent learning and trigger “calibration incomplete” or “system unavailable” messages. Many Acura Mdx platforms require static, dynamic, or a dual process depending on what was disturbed (camera vs radar), and some also require steering angle sensor initialization. Calibration is not a reset: if alignment is out of spec, voltage is unstable, or the camera/radar area is obstructed, the warning may return even after an attempted routine. Bang AutoGlass offers mobile next-day windshield replacement and can help you plan the required OEM calibration.
Proving the Repair Worked on Acura Mdx: Post-Scan, Verification Drive, and Documentation
After ADAS-related work on a Acura Mdx, a warning light turning off is helpful, but proper closeout requires proof. Begin with a post-repair diagnostic scan across all relevant modules to confirm ADAS-related DTCs are cleared and no new communication, camera, or radar faults are present. If calibration or initialization was performed, retain the completion report showing which routines ran (camera, radar, steering angle sensor as applicable) and that each finished successfully. Next, follow OEM guidance for functional validation. When required, complete a verification drive to confirm lane keep assist stays available, adaptive cruise control engages and holds, and forward collision warning operates normally without “system limited” messages. Also check practical items that affect performance: the windshield camera zone is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare in the camera’s view. Finally, keep documentation organized—pre-scan and post-scan results, OEM procedure references, calibration reports, and road-test notes—to support insurance reimbursement and reduce disputes later. Bang AutoGlass makes the glass portion simple with mobile, as-soon-as-next-day service; most installs take 30–45 minutes plus at least 1 hour of safe drive-away time, and workmanship is backed by a lifetime warranty.
Services
Service Areas
ADAS Warning Lights on Acura Mdx: What the Icons and Messages Commonly Indicate
ADAS warning lights on a Acura Mdx are a status signal from the driver-assist system: a feature is limited, unavailable, or requesting service. The icon hints at what’s affected—a car between lane lines for Lane Keep Assist/Lane Departure Warning, a crash/impact graphic for Forward Collision Warning or Automatic Emergency Braking, and a cruise/speedometer symbol for Adaptive Cruise Control. Many clusters also display “Camera Obscured,” “Front Radar Blocked,” “ACC Unavailable,” or “Driver Assist Limited” when sensors can’t see well enough to pass their self-check. Rule out simple visibility problems first. Clean the windshield inside and out at the camera window near the rearview mirror; haze, fogging, frost, and wiper streaks can reduce contrast and disable lane tracking. Confirm washer spray and wiper blades clear without smearing. Then wipe the front emblem/radar cover and remove bugs, mud, snow, or ice. In heavy rain, glare, fog, or blowing snow, brief dropouts can be normal. If the warning started after a rock chip, crack, windshield replacement, or a front-end bump, calibration may be required. Bang AutoGlass offers mobile windshield replacement as soon as next day, 30–45 minute installs, at least 1 hour safe drive-away time, insurance support, and a lifetime workmanship warranty.
When Calibration Is the Fix for Acura Mdx: Post-Windshield Replacement and Sensor Alignment Triggers
On a Acura Mdx, calibration is often the right fix when ADAS warnings appear right after a windshield replacement or work that disturbed the forward camera or front radar. Aiming tolerances are tight, and the software expects sensors to sit at a precise angle and position. If the wrong windshield is installed, a camera bracket shifts, or a radar mount moves during bumper work, the vehicle may disable features like Lane Keep Assist or Adaptive Cruise Control and show messages such as “Calibration Required,” “ACC Unavailable,” or “Driver Assist Limited.” Calibration may also be required after changes that alter vehicle geometry: collision repair, bumper removal, wheel alignment, suspension or ride-height work, steering service, or non-OEM tire sizing. Even light contact can bend a radar bracket enough to fail a self-check. Follow OEM sequence. Verify the correct windshield for the Acura Mdx, confirm the camera mount and radar cover are clean and intact, run a diagnostic pre-scan, complete the required static and/or dynamic procedure, then do a post-scan to confirm systems re-enable. Bang AutoGlass provides mobile replacement as soon as next day (30–45 minutes plus at least 1 hour safe drive-away time) and a lifetime workmanship warranty.
When It’s Not Calibration on Acura Mdx: Obstructions, Damage, Voltage, Wiring, and Module Faults
On a Acura Mdx, an ADAS warning light does not automatically mean calibration is needed. Many systems pause whenever sensor input is unreliable. Weather and road conditions are common causes: heavy rain, snow, fog, glare, or road spray can reduce camera contrast and prevent tracking of lane markings or vehicles, leading to “Camera Obscured” or “Driver Assist Limited.” Features often return once visibility improves. Obstructions and add-ons can create the same symptoms. Dashcams, toll tags, stickers, and poorly placed tint near the camera window can block the forward view. Up front, a cracked, misaligned, or painted radar cover/emblem can interrupt the signal and trigger “Front Radar Blocked” or “ACC Unavailable.” Electrical stability matters, too: a weak 12-volt battery or recent battery disconnect can set low-voltage or communication faults that take modules offline. If warnings persist after cleaning, treat it as diagnostics. A DTC scan helps distinguish a blocked sensor from fuse, ground, connector, corrosion, harness, camera/radar unit, or software issues. If the warning began after windshield damage, replacement, or a front-end impact, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Acura Mdx: Reading DTCs, Root-Cause Checks, and OEM Procedures
When ADAS warning lights appear on a Acura Mdx, the quickest route to a correct fix is a structured diagnostic process guided by scan results and OEM procedures. Messages indicate a limitation, not the underlying fault. That is why manufacturers recommend pre- and post-repair scanning whenever the windshield camera, front radar, or related steering/braking inputs have been disturbed—often after windshield replacement, bumper removal, collision repair, alignment changes, suspension work, or low-voltage events. Begin with a complete pre-scan (health check). Pull DTCs from all relevant modules because ADAS depends on ABS, steering angle, yaw/acceleration sensors, and network communications. Save code status and freeze-frame details before clearing anything. Then follow OEM root-cause checks: confirm battery/charging stability, inspect fuses and grounds, and examine connectors and harnesses at the camera and radar for looseness, corrosion, or pin-fit issues. Verify correct windshield specification, an intact camera bracket, clean viewing zones, and an undamaged radar cover aligned correctly. Confirm baseline conditions that affect aiming and eligibility—tire size/pressure, ride height, and alignment within specification. After repairs and any required calibration/initialization, run a post-scan to verify related DTCs are cleared and do not return. Bang AutoGlass offers mobile next-day service and can coordinate OEM calibration for your Acura Mdx.
Static vs Dynamic ADAS Calibration for Acura Mdx: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both return your Acura Mdx to OEM aiming specs, but they work differently and have strict prerequisites. Static calibration is done with the vehicle stationary in a controlled bay using OEM targets, measurements, and a scan tool to start the routine. Success typically requires a level floor, precise target distance/height, consistent lighting, correct tire pressures and tire size, normal ride height, and no active DTCs that would block the procedure. Dynamic calibration is completed on the road. The technician puts the system in learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, time or distance requirements, clear lane markings, and good visibility. Weather, traffic, construction zones, glare, or inconsistent lane paint can prevent learning and trigger “calibration incomplete” or “system unavailable” messages. Many Acura Mdx platforms require static, dynamic, or a dual process depending on what was disturbed (camera vs radar), and some also require steering angle sensor initialization. Calibration is not a reset: if alignment is out of spec, voltage is unstable, or the camera/radar area is obstructed, the warning may return even after an attempted routine. Bang AutoGlass offers mobile next-day windshield replacement and can help you plan the required OEM calibration.
Proving the Repair Worked on Acura Mdx: Post-Scan, Verification Drive, and Documentation
After ADAS-related work on a Acura Mdx, a warning light turning off is helpful, but proper closeout requires proof. Begin with a post-repair diagnostic scan across all relevant modules to confirm ADAS-related DTCs are cleared and no new communication, camera, or radar faults are present. If calibration or initialization was performed, retain the completion report showing which routines ran (camera, radar, steering angle sensor as applicable) and that each finished successfully. Next, follow OEM guidance for functional validation. When required, complete a verification drive to confirm lane keep assist stays available, adaptive cruise control engages and holds, and forward collision warning operates normally without “system limited” messages. Also check practical items that affect performance: the windshield camera zone is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare in the camera’s view. Finally, keep documentation organized—pre-scan and post-scan results, OEM procedure references, calibration reports, and road-test notes—to support insurance reimbursement and reduce disputes later. Bang AutoGlass makes the glass portion simple with mobile, as-soon-as-next-day service; most installs take 30–45 minutes plus at least 1 hour of safe drive-away time, and workmanship is backed by a lifetime warranty.
Enjoy More Relevant Blogs
How to Schedule ADAS Calibration for Acura Mdx After Windshield Replacement
Schedule ADAS calibration for Acura Mdx after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
Do You Need ADAS Calibration for Acura Mdx After a Wheel Alignment, Suspension Work, or a Minor Collision?
Do you need ADAS calibration for a Acura Mdx after alignment, suspension work, or a minor collision? Signs, timelines, safety risks, and costs today.
ADAS Calibration Checklist for Acura Mdx: Documentation, Verification, and Final Safety Checks
ADAS calibration checklist for Acura Mdx: documentation to request, scans to verify, and safety checks that confirm cameras and sensors are set right.
Static vs Dynamic ADAS Calibration for Acura Mdx: What the Difference Means
Static vs dynamic ADAS calibration for Acura Mdx: key differences, when each is required, how long it takes, and what affects accuracy for safety.
How Much Does ADAS Calibration Cost for Acura Mdx? What Drives Pricing and What Insurance Typically Covers
How much does ADAS calibration cost for a Acura Mdx? Learn pricing drivers, camera vs radar needs, labor time, and what insurance typically covers.
OEM Calibration Requirements for Acura Mdx: How to Confirm What Must Be Calibrated
OEM calibration requirements for Acura Mdx: how to confirm what must be calibrated after repairs, what triggers recalibration, and what proof to ask for.
Camera Calibration for Acura Mdx: Lane Assist and Forward Collision Accuracy Explained
Need camera calibration for your Acura Mdx? See how calibration affects lane assist and forward collision accuracy after windshield service or repairs.
Mobile ADAS Calibration for Acura Mdx: What to Expect On-Site and Why Setup Matters
Mobile ADAS calibration for Acura Mdx: what to expect on-site, space and lighting needs, and why setup and verification matter after repairs today.
Pre- and Post-Calibration Scans for Acura Mdx: Proving Systems Are Set Correctly
Pre- and post-calibration scans for Acura Mdx: see why scans matter, what they verify, and how reports prove ADAS systems are set correctly after service.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm