Services
Service Areas
Do You Need ADAS Calibration for Audi Rs 7 After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
A Audi Rs 7 can drive straight after an alignment and still have ADAS that’s slightly out of sync if the reference angles changed. Lane-keeping assist and lane departure warning use lane lines from the forward camera, but the software also depends on the vehicle’s calibrated centerline and an accurate steering angle sensor (SAS) baseline. ACC and AEB likewise assume the camera/radar are aimed relative to the true direction of travel. When a technician adjusts toe, camber, caster, or corrects thrust angle, the Audi Rs 7 may follow a subtly different path than before. If the SAS zero point and sensor aiming are not updated, the system can misread what “straight ahead” is. That’s why OEM workflows often pair alignment with a scan-tool routine: pre-scan for stored codes, SAS reset or relearn, then calibration verification for the front camera and/or radar using static targets, a dynamic road drive, or both. A practical red flag is an alignment invoice with no post-scan results or calibration documentation. In real driving, miscalibration can feel like drifting lane centering, ACC that changes following behavior unexpectedly, or warnings that trigger too early or too late. Choose providers that confirm alignment specs first and then record the calibration outcome.
Audi Rs 7 ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Audi Rs 7—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Audi Rs 7 set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Audi Rs 7 After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
It doesn’t take a major crash to push ADAS out of spec on a Audi Rs 7. A light rear-end, slow-speed bumper hit, or curb impact can transfer force into the bumper structure, sensor brackets, or windshield/camera area. Because radar and camera assemblies are aimed within very small tolerances, a tiny shift in a bracket, bumper reinforcement, or camera mount can change what the system “thinks” is straight ahead. The symptoms may be subtle: ACC that feels inconsistent, forward-collision warnings that seem early or late, lane-keeping that drifts, or intermittent false alerts. Often there is no warning light, so the reliable approach is to scan for stored codes and follow OEM calibration requirements. Post-impact best practice is a diagnostic pre-scan, any required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status. Save the calibration report with your repair paperwork, since insurers and future shops often ask for proof. If the incident also damaged your windshield—especially on Audi Rs 7 trims with windshield-mounted cameras—Bang AutoGlass can provide mobile replacement when scheduling allows. Most installs take 30–45 minutes; plan at least one hour of safe drive time for adhesive cure. We can also help you organize scan results and direct you to an appropriate calibration resource.
Signs Your Audi Rs 7 ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
On a Audi Rs 7, ADAS calibration problems do not always look like a dramatic failure. A dashboard message for the camera, radar, lane assist, or ACC is a clear indicator, but many drivers notice subtle changes first: lane-keeping that favors one side, lane departure warnings that feel overly sensitive, or lane-centering that wanders on roads with clear markings. Adaptive cruise control (ACC) may brake too aggressively, vary the following gap, or react late to vehicles ahead. You might also get random forward-collision warnings or blind-spot alerts at the wrong times. These symptoms can happen when sensor aim is slightly off, a radar bracket shifted, a windshield-mounted camera moved, or the steering angle sensor baseline no longer matches straight-ahead. The best clue is timing. If the behavior began after windshield replacement, alignment, suspension/steering repair, bumper work, or a minor impact, treat calibration verification as a safety step. An OEM-aligned approach is: scan for codes, confirm prerequisites (tires, ride height, alignment), complete static and/or dynamic calibration, then document results. If cracked glass is involved, Bang AutoGlass provides next-day mobile windshield replacement when scheduling allows. Most replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and are backed by a lifetime workmanship warranty.
How Shops Confirm Audi Rs 7 ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
When a shop says your Audi Rs 7 ADAS is "good," ask what evidence supports that claim. The standard is an OEM-style process with paperwork. It typically begins with a pre-scan to find diagnostic trouble codes (DTCs) and module status across camera, radar, braking, and lane-assist systems, including history faults that may not trigger a warning light. Next, the shop confirms calibration prerequisites: correct tire size and pressure, proper ride height, no looseness in steering/suspension components, and alignment within spec (including thrust angle). Those checks matter because camera calibration and radar calibration assume the vehicle's geometry is correct. After prerequisites, procedure selection depends on your Audi Rs 7 trim and options. A windshield replacement, bumper repair, alignment, or suspension work may require target-based static calibration, a scan-tool initiated dynamic road routine, or both, sometimes across multiple systems (front camera, front radar, steering angle sensor reset). Once complete, a post-scan verifies normal status and cleared codes. Request the deliverables: pre-scan and post-scan printouts, alignment measurements if performed, and the ADAS calibration report showing completion and final pass status for insurance and your records.
Insurance and Warranty Questions for Audi Rs 7 ADAS Calibration: What’s Typically Covered and What to Document
Insurance and warranty questions are common with Audi Rs 7 ADAS calibration because coverage depends on what triggered the work. Calibrations tied to collision repairs (bumper damage, bracket replacement, suspension impact) are typically handled under collision coverage, while calibrations associated with windshield replacement are often processed under comprehensive coverage when a windshield-mounted camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Policies and deductibles vary, so confirm whether diagnostic scanning and camera calibration/radar calibration are reimbursable line items for your specific claim. Documentation is your leverage. Keep a repair order stating the trigger (windshield replacement, wheel alignment, suspension work, or minor collision), photos of the affected area, alignment printouts if geometry was involved, and the pre-scan and post-scan results. Most importantly, request the ADAS calibration report showing the completed procedure and final pass status. Clear, itemized invoices that separate glass, scanning, and calibration reduce adjuster pushback. Bang AutoGlass can streamline the glass side: we work with all insurance companies when comprehensive coverage applies and provide next-day mobile service when scheduling allows. Most windshield replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
Services
Service Areas
Do You Need ADAS Calibration for Audi Rs 7 After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
A Audi Rs 7 can drive straight after an alignment and still have ADAS that’s slightly out of sync if the reference angles changed. Lane-keeping assist and lane departure warning use lane lines from the forward camera, but the software also depends on the vehicle’s calibrated centerline and an accurate steering angle sensor (SAS) baseline. ACC and AEB likewise assume the camera/radar are aimed relative to the true direction of travel. When a technician adjusts toe, camber, caster, or corrects thrust angle, the Audi Rs 7 may follow a subtly different path than before. If the SAS zero point and sensor aiming are not updated, the system can misread what “straight ahead” is. That’s why OEM workflows often pair alignment with a scan-tool routine: pre-scan for stored codes, SAS reset or relearn, then calibration verification for the front camera and/or radar using static targets, a dynamic road drive, or both. A practical red flag is an alignment invoice with no post-scan results or calibration documentation. In real driving, miscalibration can feel like drifting lane centering, ACC that changes following behavior unexpectedly, or warnings that trigger too early or too late. Choose providers that confirm alignment specs first and then record the calibration outcome.
Audi Rs 7 ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Audi Rs 7—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Audi Rs 7 set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Audi Rs 7 After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
It doesn’t take a major crash to push ADAS out of spec on a Audi Rs 7. A light rear-end, slow-speed bumper hit, or curb impact can transfer force into the bumper structure, sensor brackets, or windshield/camera area. Because radar and camera assemblies are aimed within very small tolerances, a tiny shift in a bracket, bumper reinforcement, or camera mount can change what the system “thinks” is straight ahead. The symptoms may be subtle: ACC that feels inconsistent, forward-collision warnings that seem early or late, lane-keeping that drifts, or intermittent false alerts. Often there is no warning light, so the reliable approach is to scan for stored codes and follow OEM calibration requirements. Post-impact best practice is a diagnostic pre-scan, any required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status. Save the calibration report with your repair paperwork, since insurers and future shops often ask for proof. If the incident also damaged your windshield—especially on Audi Rs 7 trims with windshield-mounted cameras—Bang AutoGlass can provide mobile replacement when scheduling allows. Most installs take 30–45 minutes; plan at least one hour of safe drive time for adhesive cure. We can also help you organize scan results and direct you to an appropriate calibration resource.
Signs Your Audi Rs 7 ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
On a Audi Rs 7, ADAS calibration problems do not always look like a dramatic failure. A dashboard message for the camera, radar, lane assist, or ACC is a clear indicator, but many drivers notice subtle changes first: lane-keeping that favors one side, lane departure warnings that feel overly sensitive, or lane-centering that wanders on roads with clear markings. Adaptive cruise control (ACC) may brake too aggressively, vary the following gap, or react late to vehicles ahead. You might also get random forward-collision warnings or blind-spot alerts at the wrong times. These symptoms can happen when sensor aim is slightly off, a radar bracket shifted, a windshield-mounted camera moved, or the steering angle sensor baseline no longer matches straight-ahead. The best clue is timing. If the behavior began after windshield replacement, alignment, suspension/steering repair, bumper work, or a minor impact, treat calibration verification as a safety step. An OEM-aligned approach is: scan for codes, confirm prerequisites (tires, ride height, alignment), complete static and/or dynamic calibration, then document results. If cracked glass is involved, Bang AutoGlass provides next-day mobile windshield replacement when scheduling allows. Most replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and are backed by a lifetime workmanship warranty.
How Shops Confirm Audi Rs 7 ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
When a shop says your Audi Rs 7 ADAS is "good," ask what evidence supports that claim. The standard is an OEM-style process with paperwork. It typically begins with a pre-scan to find diagnostic trouble codes (DTCs) and module status across camera, radar, braking, and lane-assist systems, including history faults that may not trigger a warning light. Next, the shop confirms calibration prerequisites: correct tire size and pressure, proper ride height, no looseness in steering/suspension components, and alignment within spec (including thrust angle). Those checks matter because camera calibration and radar calibration assume the vehicle's geometry is correct. After prerequisites, procedure selection depends on your Audi Rs 7 trim and options. A windshield replacement, bumper repair, alignment, or suspension work may require target-based static calibration, a scan-tool initiated dynamic road routine, or both, sometimes across multiple systems (front camera, front radar, steering angle sensor reset). Once complete, a post-scan verifies normal status and cleared codes. Request the deliverables: pre-scan and post-scan printouts, alignment measurements if performed, and the ADAS calibration report showing completion and final pass status for insurance and your records.
Insurance and Warranty Questions for Audi Rs 7 ADAS Calibration: What’s Typically Covered and What to Document
Insurance and warranty questions are common with Audi Rs 7 ADAS calibration because coverage depends on what triggered the work. Calibrations tied to collision repairs (bumper damage, bracket replacement, suspension impact) are typically handled under collision coverage, while calibrations associated with windshield replacement are often processed under comprehensive coverage when a windshield-mounted camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Policies and deductibles vary, so confirm whether diagnostic scanning and camera calibration/radar calibration are reimbursable line items for your specific claim. Documentation is your leverage. Keep a repair order stating the trigger (windshield replacement, wheel alignment, suspension work, or minor collision), photos of the affected area, alignment printouts if geometry was involved, and the pre-scan and post-scan results. Most importantly, request the ADAS calibration report showing the completed procedure and final pass status. Clear, itemized invoices that separate glass, scanning, and calibration reduce adjuster pushback. Bang AutoGlass can streamline the glass side: we work with all insurance companies when comprehensive coverage applies and provide next-day mobile service when scheduling allows. Most windshield replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
Services
Service Areas
Do You Need ADAS Calibration for Audi Rs 7 After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
A Audi Rs 7 can drive straight after an alignment and still have ADAS that’s slightly out of sync if the reference angles changed. Lane-keeping assist and lane departure warning use lane lines from the forward camera, but the software also depends on the vehicle’s calibrated centerline and an accurate steering angle sensor (SAS) baseline. ACC and AEB likewise assume the camera/radar are aimed relative to the true direction of travel. When a technician adjusts toe, camber, caster, or corrects thrust angle, the Audi Rs 7 may follow a subtly different path than before. If the SAS zero point and sensor aiming are not updated, the system can misread what “straight ahead” is. That’s why OEM workflows often pair alignment with a scan-tool routine: pre-scan for stored codes, SAS reset or relearn, then calibration verification for the front camera and/or radar using static targets, a dynamic road drive, or both. A practical red flag is an alignment invoice with no post-scan results or calibration documentation. In real driving, miscalibration can feel like drifting lane centering, ACC that changes following behavior unexpectedly, or warnings that trigger too early or too late. Choose providers that confirm alignment specs first and then record the calibration outcome.
Audi Rs 7 ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Audi Rs 7—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Audi Rs 7 set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Audi Rs 7 After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
It doesn’t take a major crash to push ADAS out of spec on a Audi Rs 7. A light rear-end, slow-speed bumper hit, or curb impact can transfer force into the bumper structure, sensor brackets, or windshield/camera area. Because radar and camera assemblies are aimed within very small tolerances, a tiny shift in a bracket, bumper reinforcement, or camera mount can change what the system “thinks” is straight ahead. The symptoms may be subtle: ACC that feels inconsistent, forward-collision warnings that seem early or late, lane-keeping that drifts, or intermittent false alerts. Often there is no warning light, so the reliable approach is to scan for stored codes and follow OEM calibration requirements. Post-impact best practice is a diagnostic pre-scan, any required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status. Save the calibration report with your repair paperwork, since insurers and future shops often ask for proof. If the incident also damaged your windshield—especially on Audi Rs 7 trims with windshield-mounted cameras—Bang AutoGlass can provide mobile replacement when scheduling allows. Most installs take 30–45 minutes; plan at least one hour of safe drive time for adhesive cure. We can also help you organize scan results and direct you to an appropriate calibration resource.
Signs Your Audi Rs 7 ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
On a Audi Rs 7, ADAS calibration problems do not always look like a dramatic failure. A dashboard message for the camera, radar, lane assist, or ACC is a clear indicator, but many drivers notice subtle changes first: lane-keeping that favors one side, lane departure warnings that feel overly sensitive, or lane-centering that wanders on roads with clear markings. Adaptive cruise control (ACC) may brake too aggressively, vary the following gap, or react late to vehicles ahead. You might also get random forward-collision warnings or blind-spot alerts at the wrong times. These symptoms can happen when sensor aim is slightly off, a radar bracket shifted, a windshield-mounted camera moved, or the steering angle sensor baseline no longer matches straight-ahead. The best clue is timing. If the behavior began after windshield replacement, alignment, suspension/steering repair, bumper work, or a minor impact, treat calibration verification as a safety step. An OEM-aligned approach is: scan for codes, confirm prerequisites (tires, ride height, alignment), complete static and/or dynamic calibration, then document results. If cracked glass is involved, Bang AutoGlass provides next-day mobile windshield replacement when scheduling allows. Most replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and are backed by a lifetime workmanship warranty.
How Shops Confirm Audi Rs 7 ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
When a shop says your Audi Rs 7 ADAS is "good," ask what evidence supports that claim. The standard is an OEM-style process with paperwork. It typically begins with a pre-scan to find diagnostic trouble codes (DTCs) and module status across camera, radar, braking, and lane-assist systems, including history faults that may not trigger a warning light. Next, the shop confirms calibration prerequisites: correct tire size and pressure, proper ride height, no looseness in steering/suspension components, and alignment within spec (including thrust angle). Those checks matter because camera calibration and radar calibration assume the vehicle's geometry is correct. After prerequisites, procedure selection depends on your Audi Rs 7 trim and options. A windshield replacement, bumper repair, alignment, or suspension work may require target-based static calibration, a scan-tool initiated dynamic road routine, or both, sometimes across multiple systems (front camera, front radar, steering angle sensor reset). Once complete, a post-scan verifies normal status and cleared codes. Request the deliverables: pre-scan and post-scan printouts, alignment measurements if performed, and the ADAS calibration report showing completion and final pass status for insurance and your records.
Insurance and Warranty Questions for Audi Rs 7 ADAS Calibration: What’s Typically Covered and What to Document
Insurance and warranty questions are common with Audi Rs 7 ADAS calibration because coverage depends on what triggered the work. Calibrations tied to collision repairs (bumper damage, bracket replacement, suspension impact) are typically handled under collision coverage, while calibrations associated with windshield replacement are often processed under comprehensive coverage when a windshield-mounted camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Policies and deductibles vary, so confirm whether diagnostic scanning and camera calibration/radar calibration are reimbursable line items for your specific claim. Documentation is your leverage. Keep a repair order stating the trigger (windshield replacement, wheel alignment, suspension work, or minor collision), photos of the affected area, alignment printouts if geometry was involved, and the pre-scan and post-scan results. Most importantly, request the ADAS calibration report showing the completed procedure and final pass status. Clear, itemized invoices that separate glass, scanning, and calibration reduce adjuster pushback. Bang AutoGlass can streamline the glass side: we work with all insurance companies when comprehensive coverage applies and provide next-day mobile service when scheduling allows. Most windshield replacements take 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
Enjoy More Relevant Blogs
ADAS Calibration Checklist for Audi Rs 7: Documentation, Verification, and Final Safety Checks
ADAS calibration checklist for Audi Rs 7: documentation to request, scans to verify, and safety checks that confirm cameras and sensors are set right.
How Much Does ADAS Calibration Cost for Audi Rs 7? What Drives Pricing and What Insurance Typically Covers
How much does ADAS calibration cost for a Audi Rs 7? Learn pricing drivers, camera vs radar needs, labor time, and what insurance typically covers.
Static vs Dynamic ADAS Calibration for Audi Rs 7: What the Difference Means
Static vs dynamic ADAS calibration for Audi Rs 7: key differences, when each is required, how long it takes, and what affects accuracy for safety.
Mobile ADAS Calibration for Audi Rs 7: What to Expect On-Site and Why Setup Matters
Mobile ADAS calibration for Audi Rs 7: what to expect on-site, space and lighting needs, and why setup and verification matter after repairs today.
OEM Calibration Requirements for Audi Rs 7: How to Confirm What Must Be Calibrated
OEM calibration requirements for Audi Rs 7: how to confirm what must be calibrated after repairs, what triggers recalibration, and what proof to ask for.
Camera Calibration for Audi Rs 7: Lane Assist and Forward Collision Accuracy Explained
Need camera calibration for your Audi Rs 7? See how calibration affects lane assist and forward collision accuracy after windshield service or repairs.
How to Schedule ADAS Calibration for Audi Rs 7 After Windshield Replacement
Schedule ADAS calibration for Audi Rs 7 after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
Pre- and Post-Calibration Scans for Audi Rs 7: Proving Systems Are Set Correctly
Pre- and post-calibration scans for Audi Rs 7: see why scans matter, what they verify, and how reports prove ADAS systems are set correctly after service.
ADAS Warning Lights on Audi Rs 7: When Calibration Is the Fix and When It’s Not
ADAS warning lights on your Audi Rs 7? Learn when calibration fixes lane assist or AEB issues, when it will not, and what to check next. Schedule help.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm