Services
Service Areas
Post-Install Checks for Bmw 2 Series Gran Coupe: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-Install Walkaround for Bmw 2 Series Gran Coupe: Rear Glass Fit, Trim, and Bead Consistency
Rear window replacement quality on a Bmw 2 Series Gran Coupe is confirmed after installation with a checklist. Begin with alignment: verify the backlite follows the dry-fit marks, then walk the perimeter to confirm a consistent reveal and even flushness to body lines. Next, check molding and trim seating. The perimeter molding should be flat and continuous with no loose corners, waves at the roof edge, or gaps down the C-pillars or across the decklid line. Parts removed for access, such as a rear wiper, spoiler, applique, or high-mount brake light trim (when equipped), should be reinstalled straight with clips locked and hardware tight. Then verify adhesive integrity. A proper urethane bond shows a continuous bead path, smooth corner transitions, and controlled squeeze-out, indicating full contact to the pinch weld and frit area. Watch for pockets, bubbles, or discontinuities that can lead to leaks, wind noise, or rattles. Finish with surface and interior checks: inspect for chips or scratches, confirm DOT/part details match the job record, clean off residue, and ensure headliner edges, garnish moldings, and wiring routes are seated with nothing pinched. Verify rear defroster and antenna connections (if equipped). Bang AutoGlass uses this process to deliver a clean, quiet Bmw 2 Series Gran Coupe rear glass replacement backed by a lifetime workmanship warranty.
Minimum Drive-Away Time After Rear Glass Replacement: Adhesive Cure and Release Guidance
Safe drive-away time (SDAT) after a Bmw 2 Series Gran Coupe rear glass replacement is the minimum stationary period needed for the urethane adhesive to gain early handling strength. The correct release time is not universal; it depends on the adhesive system and on jobsite conditions such as temperature and humidity, which is why a professional installer provides guidance specific to your installation. Driving too soon can disturb the bond line through body flex, vibration, and cabin-pressure changes, increasing the chance of wind noise, leaks, or reduced retention over time. For Bang AutoGlass customers, the timeline is straightforward: most replacements take about 30-45 minutes, and we recommend at least 1 hour of stationary time afterward before driving. During the wait, avoid slamming doors and, when possible, keep one window slightly cracked to reduce pressure spikes against the new seal. Once you are released, drive gently for the remainder of the day and avoid potholes, rough roads, and extended freeway runs when you can. For the first 24 hours, skip automatic washes and avoid directing high-pressure water at the glass edges so the adhesive can continue curing and moldings stay seated. We are a mobile glass company, so service is completed where your Bmw 2 Series Gran Coupe is parked, and we work with all insurance companies.
Rear Glass Leak Test for Bmw 2 Series Gran Coupe: Water-Test Steps and Common Leak Points
A low-pressure water test is a practical way to confirm sealing after a Bmw 2 Series Gran Coupe rear glass replacement. Use an open-end hose with no nozzle to mimic rain instead of forcing water at the urethane. Place a helper inside with a flashlight and towels to watch the headliner edge, rear pillars, and package tray for the first sign of dampness or tracking. Outside, test in a deliberate sequence. Start on the roof above the backlite and let water sheet down, then sweep across the top edge and pause at both upper corners. Move down one side, then the other, holding flow at molding joints or clip locations. Finish along the lower edge at the decklid line and pause at both lower corners. After the perimeter, wet nearby items that can appear like a rear window leak, including the center high-mounted stop lamp gasket and, if equipped, the roof antenna seal. If moisture appears, write down where water was applied when it started and where it first appeared inside. That detail helps isolate bead voids, corner discontinuities, or tracking from a neighboring seal. Bang AutoGlass can inspect and re-seal on-site, supported by our lifetime workmanship warranty for your Bmw 2 Series Gran Coupe.
Wind Noise Troubleshooting on Bmw 2 Series Gran Coupe: Whistle vs Rush and How to Isolate the Cause
Wind noise on a Bmw 2 Series Gran Coupe after rear glass replacement usually shows up as either a sharp whistle or a steady rushing sound. A whistle points to a small air leak—like a lifted molding corner, a trim clip not fully seated, or a tiny void in the urethane bead. A rush suggests a larger path, such as perimeter trim not sitting flush, the backlite slightly off-center, or uneven seal contact. Recreate the noise at a consistent speed and note whether crosswinds or cracking a window changes it. If possible, have someone listen from the rear seat to identify the loudest side. Then run a painter’s tape test: cover one edge at a time (upper corners first, then vertical sides, then the lower edge) and take a short drive. When the sound changes, you’ve isolated the problem zone. Inspect that area for gaps, trim sitting proud of the body line, or an uneven reveal. Also rule out look-alikes like roof racks, hatch weatherstripping, door seals, and a loose license-plate bracket. Because the same openings can become leaks, address new noise promptly. Bang AutoGlass can re-check fit and sealing with mobile service, backed by our lifetime workmanship warranty.
Rattle Test After Rear Glass Replacement: Interior Panels, Moldings, and Loose Hardware
When a Bmw 2 Series Gran Coupe rattles after rear window replacement, assume it’s trim, clips, or hardware that shifted during reassembly—not the glass. Start parked. Press along the rear headliner edge, down each C-pillar panel, and across the package tray, then tap nearby trim. Any spot that changes sound under pressure is a likely interface, and a plastic buzz usually means a partially seated clip. Check common sources near the backlite: the third brake light housing, speaker grilles, rear wiper trim (if equipped), seat belt upper anchor trim, and child-seat anchor covers. If a spoiler or applique was removed for access, confirm fasteners are tight and clips are fully locked. Also verify wiring retainers; a loose harness can contact metal and mimic a “rear glass” rattle. Then drive a short, bumpy route at low speed with the radio off. Have a helper in the rear seat apply gentle pressure to one section at a time; when the noise changes, you’ve identified the source zone. Fixes typically involve reseating panels, replacing damaged clips, adding felt/foam tape at contact points, and securing wiring. Bang AutoGlass can correct this on-site with mobile service, backed by our lifetime workmanship warranty.
Final QC and Documentation: Rear Defroster/Antenna Checks and What to Record
Final QC on a Bmw 2 Series Gran Coupe rear glass replacement should verify electrical functions, sealing, and documentation. Start with the rear defroster. Confirm both connectors are firmly attached to the glass tabs, then test the switch and fuse. For a technical confirmation, use a multimeter to check continuity at the tabs and across the grid; this approach is preferred over a test light because it avoids adding load to the circuit. If your Bmw 2 Series Gran Coupe uses a glass-integrated antenna, verify radio reception is comparable to pre-service and that the antenna lead or amplifier connection is secured and not pinched behind trim. Next, confirm fit and finish: consistent reveal, moldings seated flush with no lifted corners, and a short drive to ensure there’s no new wind noise. When appropriate, document a low-pressure water test for leak prevention. Inside, confirm the headliner edge is seated, garnish panels are fully clipped, and wiring is routed into retainers so nothing can buzz or rattle. For records, capture year/Bmw/2 Series Gran Coupe, glass type and DOT/part markings, date and service location, and photos. Bang AutoGlass rear glass replacements typically take 30–45 minutes, followed by at least 1 hour stationary before driving, and our lifetime workmanship warranty supports the work.
Services
Service Areas
Post-Install Checks for Bmw 2 Series Gran Coupe: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-Install Walkaround for Bmw 2 Series Gran Coupe: Rear Glass Fit, Trim, and Bead Consistency
Rear window replacement quality on a Bmw 2 Series Gran Coupe is confirmed after installation with a checklist. Begin with alignment: verify the backlite follows the dry-fit marks, then walk the perimeter to confirm a consistent reveal and even flushness to body lines. Next, check molding and trim seating. The perimeter molding should be flat and continuous with no loose corners, waves at the roof edge, or gaps down the C-pillars or across the decklid line. Parts removed for access, such as a rear wiper, spoiler, applique, or high-mount brake light trim (when equipped), should be reinstalled straight with clips locked and hardware tight. Then verify adhesive integrity. A proper urethane bond shows a continuous bead path, smooth corner transitions, and controlled squeeze-out, indicating full contact to the pinch weld and frit area. Watch for pockets, bubbles, or discontinuities that can lead to leaks, wind noise, or rattles. Finish with surface and interior checks: inspect for chips or scratches, confirm DOT/part details match the job record, clean off residue, and ensure headliner edges, garnish moldings, and wiring routes are seated with nothing pinched. Verify rear defroster and antenna connections (if equipped). Bang AutoGlass uses this process to deliver a clean, quiet Bmw 2 Series Gran Coupe rear glass replacement backed by a lifetime workmanship warranty.
Minimum Drive-Away Time After Rear Glass Replacement: Adhesive Cure and Release Guidance
Safe drive-away time (SDAT) after a Bmw 2 Series Gran Coupe rear glass replacement is the minimum stationary period needed for the urethane adhesive to gain early handling strength. The correct release time is not universal; it depends on the adhesive system and on jobsite conditions such as temperature and humidity, which is why a professional installer provides guidance specific to your installation. Driving too soon can disturb the bond line through body flex, vibration, and cabin-pressure changes, increasing the chance of wind noise, leaks, or reduced retention over time. For Bang AutoGlass customers, the timeline is straightforward: most replacements take about 30-45 minutes, and we recommend at least 1 hour of stationary time afterward before driving. During the wait, avoid slamming doors and, when possible, keep one window slightly cracked to reduce pressure spikes against the new seal. Once you are released, drive gently for the remainder of the day and avoid potholes, rough roads, and extended freeway runs when you can. For the first 24 hours, skip automatic washes and avoid directing high-pressure water at the glass edges so the adhesive can continue curing and moldings stay seated. We are a mobile glass company, so service is completed where your Bmw 2 Series Gran Coupe is parked, and we work with all insurance companies.
Rear Glass Leak Test for Bmw 2 Series Gran Coupe: Water-Test Steps and Common Leak Points
A low-pressure water test is a practical way to confirm sealing after a Bmw 2 Series Gran Coupe rear glass replacement. Use an open-end hose with no nozzle to mimic rain instead of forcing water at the urethane. Place a helper inside with a flashlight and towels to watch the headliner edge, rear pillars, and package tray for the first sign of dampness or tracking. Outside, test in a deliberate sequence. Start on the roof above the backlite and let water sheet down, then sweep across the top edge and pause at both upper corners. Move down one side, then the other, holding flow at molding joints or clip locations. Finish along the lower edge at the decklid line and pause at both lower corners. After the perimeter, wet nearby items that can appear like a rear window leak, including the center high-mounted stop lamp gasket and, if equipped, the roof antenna seal. If moisture appears, write down where water was applied when it started and where it first appeared inside. That detail helps isolate bead voids, corner discontinuities, or tracking from a neighboring seal. Bang AutoGlass can inspect and re-seal on-site, supported by our lifetime workmanship warranty for your Bmw 2 Series Gran Coupe.
Wind Noise Troubleshooting on Bmw 2 Series Gran Coupe: Whistle vs Rush and How to Isolate the Cause
Wind noise on a Bmw 2 Series Gran Coupe after rear glass replacement usually shows up as either a sharp whistle or a steady rushing sound. A whistle points to a small air leak—like a lifted molding corner, a trim clip not fully seated, or a tiny void in the urethane bead. A rush suggests a larger path, such as perimeter trim not sitting flush, the backlite slightly off-center, or uneven seal contact. Recreate the noise at a consistent speed and note whether crosswinds or cracking a window changes it. If possible, have someone listen from the rear seat to identify the loudest side. Then run a painter’s tape test: cover one edge at a time (upper corners first, then vertical sides, then the lower edge) and take a short drive. When the sound changes, you’ve isolated the problem zone. Inspect that area for gaps, trim sitting proud of the body line, or an uneven reveal. Also rule out look-alikes like roof racks, hatch weatherstripping, door seals, and a loose license-plate bracket. Because the same openings can become leaks, address new noise promptly. Bang AutoGlass can re-check fit and sealing with mobile service, backed by our lifetime workmanship warranty.
Rattle Test After Rear Glass Replacement: Interior Panels, Moldings, and Loose Hardware
When a Bmw 2 Series Gran Coupe rattles after rear window replacement, assume it’s trim, clips, or hardware that shifted during reassembly—not the glass. Start parked. Press along the rear headliner edge, down each C-pillar panel, and across the package tray, then tap nearby trim. Any spot that changes sound under pressure is a likely interface, and a plastic buzz usually means a partially seated clip. Check common sources near the backlite: the third brake light housing, speaker grilles, rear wiper trim (if equipped), seat belt upper anchor trim, and child-seat anchor covers. If a spoiler or applique was removed for access, confirm fasteners are tight and clips are fully locked. Also verify wiring retainers; a loose harness can contact metal and mimic a “rear glass” rattle. Then drive a short, bumpy route at low speed with the radio off. Have a helper in the rear seat apply gentle pressure to one section at a time; when the noise changes, you’ve identified the source zone. Fixes typically involve reseating panels, replacing damaged clips, adding felt/foam tape at contact points, and securing wiring. Bang AutoGlass can correct this on-site with mobile service, backed by our lifetime workmanship warranty.
Final QC and Documentation: Rear Defroster/Antenna Checks and What to Record
Final QC on a Bmw 2 Series Gran Coupe rear glass replacement should verify electrical functions, sealing, and documentation. Start with the rear defroster. Confirm both connectors are firmly attached to the glass tabs, then test the switch and fuse. For a technical confirmation, use a multimeter to check continuity at the tabs and across the grid; this approach is preferred over a test light because it avoids adding load to the circuit. If your Bmw 2 Series Gran Coupe uses a glass-integrated antenna, verify radio reception is comparable to pre-service and that the antenna lead or amplifier connection is secured and not pinched behind trim. Next, confirm fit and finish: consistent reveal, moldings seated flush with no lifted corners, and a short drive to ensure there’s no new wind noise. When appropriate, document a low-pressure water test for leak prevention. Inside, confirm the headliner edge is seated, garnish panels are fully clipped, and wiring is routed into retainers so nothing can buzz or rattle. For records, capture year/Bmw/2 Series Gran Coupe, glass type and DOT/part markings, date and service location, and photos. Bang AutoGlass rear glass replacements typically take 30–45 minutes, followed by at least 1 hour stationary before driving, and our lifetime workmanship warranty supports the work.
Services
Service Areas
Post-Install Checks for Bmw 2 Series Gran Coupe: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-Install Walkaround for Bmw 2 Series Gran Coupe: Rear Glass Fit, Trim, and Bead Consistency
Rear window replacement quality on a Bmw 2 Series Gran Coupe is confirmed after installation with a checklist. Begin with alignment: verify the backlite follows the dry-fit marks, then walk the perimeter to confirm a consistent reveal and even flushness to body lines. Next, check molding and trim seating. The perimeter molding should be flat and continuous with no loose corners, waves at the roof edge, or gaps down the C-pillars or across the decklid line. Parts removed for access, such as a rear wiper, spoiler, applique, or high-mount brake light trim (when equipped), should be reinstalled straight with clips locked and hardware tight. Then verify adhesive integrity. A proper urethane bond shows a continuous bead path, smooth corner transitions, and controlled squeeze-out, indicating full contact to the pinch weld and frit area. Watch for pockets, bubbles, or discontinuities that can lead to leaks, wind noise, or rattles. Finish with surface and interior checks: inspect for chips or scratches, confirm DOT/part details match the job record, clean off residue, and ensure headliner edges, garnish moldings, and wiring routes are seated with nothing pinched. Verify rear defroster and antenna connections (if equipped). Bang AutoGlass uses this process to deliver a clean, quiet Bmw 2 Series Gran Coupe rear glass replacement backed by a lifetime workmanship warranty.
Minimum Drive-Away Time After Rear Glass Replacement: Adhesive Cure and Release Guidance
Safe drive-away time (SDAT) after a Bmw 2 Series Gran Coupe rear glass replacement is the minimum stationary period needed for the urethane adhesive to gain early handling strength. The correct release time is not universal; it depends on the adhesive system and on jobsite conditions such as temperature and humidity, which is why a professional installer provides guidance specific to your installation. Driving too soon can disturb the bond line through body flex, vibration, and cabin-pressure changes, increasing the chance of wind noise, leaks, or reduced retention over time. For Bang AutoGlass customers, the timeline is straightforward: most replacements take about 30-45 minutes, and we recommend at least 1 hour of stationary time afterward before driving. During the wait, avoid slamming doors and, when possible, keep one window slightly cracked to reduce pressure spikes against the new seal. Once you are released, drive gently for the remainder of the day and avoid potholes, rough roads, and extended freeway runs when you can. For the first 24 hours, skip automatic washes and avoid directing high-pressure water at the glass edges so the adhesive can continue curing and moldings stay seated. We are a mobile glass company, so service is completed where your Bmw 2 Series Gran Coupe is parked, and we work with all insurance companies.
Rear Glass Leak Test for Bmw 2 Series Gran Coupe: Water-Test Steps and Common Leak Points
A low-pressure water test is a practical way to confirm sealing after a Bmw 2 Series Gran Coupe rear glass replacement. Use an open-end hose with no nozzle to mimic rain instead of forcing water at the urethane. Place a helper inside with a flashlight and towels to watch the headliner edge, rear pillars, and package tray for the first sign of dampness or tracking. Outside, test in a deliberate sequence. Start on the roof above the backlite and let water sheet down, then sweep across the top edge and pause at both upper corners. Move down one side, then the other, holding flow at molding joints or clip locations. Finish along the lower edge at the decklid line and pause at both lower corners. After the perimeter, wet nearby items that can appear like a rear window leak, including the center high-mounted stop lamp gasket and, if equipped, the roof antenna seal. If moisture appears, write down where water was applied when it started and where it first appeared inside. That detail helps isolate bead voids, corner discontinuities, or tracking from a neighboring seal. Bang AutoGlass can inspect and re-seal on-site, supported by our lifetime workmanship warranty for your Bmw 2 Series Gran Coupe.
Wind Noise Troubleshooting on Bmw 2 Series Gran Coupe: Whistle vs Rush and How to Isolate the Cause
Wind noise on a Bmw 2 Series Gran Coupe after rear glass replacement usually shows up as either a sharp whistle or a steady rushing sound. A whistle points to a small air leak—like a lifted molding corner, a trim clip not fully seated, or a tiny void in the urethane bead. A rush suggests a larger path, such as perimeter trim not sitting flush, the backlite slightly off-center, or uneven seal contact. Recreate the noise at a consistent speed and note whether crosswinds or cracking a window changes it. If possible, have someone listen from the rear seat to identify the loudest side. Then run a painter’s tape test: cover one edge at a time (upper corners first, then vertical sides, then the lower edge) and take a short drive. When the sound changes, you’ve isolated the problem zone. Inspect that area for gaps, trim sitting proud of the body line, or an uneven reveal. Also rule out look-alikes like roof racks, hatch weatherstripping, door seals, and a loose license-plate bracket. Because the same openings can become leaks, address new noise promptly. Bang AutoGlass can re-check fit and sealing with mobile service, backed by our lifetime workmanship warranty.
Rattle Test After Rear Glass Replacement: Interior Panels, Moldings, and Loose Hardware
When a Bmw 2 Series Gran Coupe rattles after rear window replacement, assume it’s trim, clips, or hardware that shifted during reassembly—not the glass. Start parked. Press along the rear headliner edge, down each C-pillar panel, and across the package tray, then tap nearby trim. Any spot that changes sound under pressure is a likely interface, and a plastic buzz usually means a partially seated clip. Check common sources near the backlite: the third brake light housing, speaker grilles, rear wiper trim (if equipped), seat belt upper anchor trim, and child-seat anchor covers. If a spoiler or applique was removed for access, confirm fasteners are tight and clips are fully locked. Also verify wiring retainers; a loose harness can contact metal and mimic a “rear glass” rattle. Then drive a short, bumpy route at low speed with the radio off. Have a helper in the rear seat apply gentle pressure to one section at a time; when the noise changes, you’ve identified the source zone. Fixes typically involve reseating panels, replacing damaged clips, adding felt/foam tape at contact points, and securing wiring. Bang AutoGlass can correct this on-site with mobile service, backed by our lifetime workmanship warranty.
Final QC and Documentation: Rear Defroster/Antenna Checks and What to Record
Final QC on a Bmw 2 Series Gran Coupe rear glass replacement should verify electrical functions, sealing, and documentation. Start with the rear defroster. Confirm both connectors are firmly attached to the glass tabs, then test the switch and fuse. For a technical confirmation, use a multimeter to check continuity at the tabs and across the grid; this approach is preferred over a test light because it avoids adding load to the circuit. If your Bmw 2 Series Gran Coupe uses a glass-integrated antenna, verify radio reception is comparable to pre-service and that the antenna lead or amplifier connection is secured and not pinched behind trim. Next, confirm fit and finish: consistent reveal, moldings seated flush with no lifted corners, and a short drive to ensure there’s no new wind noise. When appropriate, document a low-pressure water test for leak prevention. Inside, confirm the headliner edge is seated, garnish panels are fully clipped, and wiring is routed into retainers so nothing can buzz or rattle. For records, capture year/Bmw/2 Series Gran Coupe, glass type and DOT/part markings, date and service location, and photos. Bang AutoGlass rear glass replacements typically take 30–45 minutes, followed by at least 1 hour stationary before driving, and our lifetime workmanship warranty supports the work.
Enjoy More Relevant Blogs
How Long Does Rear Glass Replacement Take on Bmw 2 Series Gran Coupe? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How long is Bmw 2 Series Gran Coupe rear glass replacement? Get install time, urethane cure guidelines, and drive-away timing after service. Plan your visit today.
How to Schedule Mobile Rear Glass Replacement for Bmw 2 Series Gran Coupe
Schedule mobile rear glass replacement for your Bmw 2 Series Gran Coupe in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Shattered Back Window on Bmw 2 Series Gran Coupe: A Step-by-Step Rear Glass Replacement Plan
Shattered back window on Bmw 2 Series Gran Coupe? Follow a step-by-step rear glass replacement plan, cleanup tips, defroster notes, cure time, and drive-away rules.
Tempered Safety Rear Glass Replacement for Bmw 2 Series Gran Coupe: Understanding DOT Markings and FMVSS 205
Need Bmw 2 Series Gran Coupe rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Rear Defroster Not Working on Bmw 2 Series Gran Coupe? When Rear Glass Replacement Makes More Sense Than Repair
Rear defroster not working on your Bmw 2 Series Gran Coupe? Learn common causes, when repair fails, and when rear glass replacement is the smarter fix for winter.
Rear Glass Replacement for Bmw 2 Series Gran Coupe: What to Expect During Install and Aftercare
Rear glass replacement for Bmw 2 Series Gran Coupe: what happens during install, defroster and tint considerations, cure time, and aftercare to prevent leaks long-term.
How Much Does Rear Glass Replacement Cost for Bmw 2 Series Gran Coupe? Pricing Factors, OEM vs Aftermarket, and Insurance Deductibles
Estimate Bmw 2 Series Gran Coupe rear glass replacement cost. Compare OEM vs aftermarket, labor factors, insurance deductibles, and ways to save. Request a quote.
OEM-Quality Rear Glass Replacement for Bmw 2 Series Gran Coupe: Defroster Grid and Tint-Match Checklist
OEM-quality rear glass replacement for Bmw 2 Series Gran Coupe: defroster grid and tint-match checklist, plus install tips to avoid callbacks—schedule service.
Back Glass Replacement on Bmw 2 Series Gran Coupe: Defroster Tabs, Antenna Lines, and Connector Reattachment Basics
Back glass replacement on Bmw 2 Series Gran Coupe: defroster tabs, antenna lines, and connectors explained, plus install tips to avoid damage and rework safely.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm