Services
Service Areas
Do You Need ADAS Calibration for Buick Regal GS After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
On a Buick Regal GS, a wheel alignment affects more than steering feel and tire wear—it can also shift the reference angles your Advanced Driver Assistance Systems (ADAS) use for lane-keeping assist (LKA), lane departure warning (LDW), adaptive cruise control (ACC), and automatic emergency braking (AEB). These systems rely on the vehicle’s direction of travel (thrust angle) and a correct steering angle sensor (SAS) zero point to define “straight ahead.” When toe, camber, or caster is adjusted, the Buick Regal GS may track on a slightly different line, and OEM procedures often call for a SAS reset and an ADAS calibration check so the forward camera and radar match the updated geometry. Depending on requirements, that may be a static target setup, a scan-tool guided dynamic road routine, or both. After any four-wheel alignment, ask if the shop performed a diagnostic pre-scan/post-scan and documented any required camera calibration, radar calibration, or steering angle reset. Skipping steps can show up as LKA that nudges off-center, ACC that behaves inconsistently, or alerts that seem late or overly sensitive. If you’re searching “Buick Regal GS ADAS calibration after alignment” or “ADAS calibration near me,” choose a process that verifies alignment specs first and records calibration results.
Buick Regal GS ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Buick Regal GS—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Buick Regal GS set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Buick Regal GS After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
After a minor collision in a Buick Regal GS, ADAS calibration is commonly missed because the car may appear normal. However, radar and camera assemblies are aimed within very small tolerances. A low-speed rear-end, parking-lot hit, or curb strike can shift a radar bracket behind the bumper cover or disturb a camera mount by only millimeters, yet that can change how ACC, AEB, lane-keeping assist, and forward collision warning behave. It also may not set a warning light; some systems log diagnostic trouble codes that only show on a scan, while others operate with reduced accuracy until you notice phantom alerts or inconsistent following distance. A safer workflow is a diagnostic pre-scan, any manufacturer-required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status, with the calibration report saved for your records and insurance file. If the impact also caused a chipped or cracked windshield—especially on Buick Regal GS trims with windshield-mounted cameras—Bang AutoGlass can provide mobile windshield replacement when scheduling allows. Most installs take 30–45 minutes, and we recommend at least one hour of safe drive time for adhesive cure. We can also help you document what happened and connect you to an appropriate calibration resource.
Signs Your Buick Regal GS ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
If your Buick Regal GS has ADAS, a warning light for the camera, radar, or lane assist is the obvious sign calibration may be needed. Many issues show up earlier as behavior that feels "off." Notice lane-keeping assist pulling you off-center, lane departure alerts firing too often, or lane-centering that wanders instead of holding steady. Adaptive cruise control (ACC) can also change: inconsistent following distance, abrupt braking, or unexpected speed changes may mean the camera or radar view is no longer aligned with the vehicle's centerline. Other clues include false forward-collision warnings or blind-spot monitoring that misses vehicles. If this started right after windshield replacement with a windshield-mounted camera, wheel alignment, suspension/steering work, bumper repair, or a minor hit, assume calibration prerequisites shifted. The fix is a scan for codes and an OEM-procedure static and/or dynamic calibration, documented with a calibration report. For searches like "Buick Regal GS ADAS calibration near me," choose a shop that can scan, calibrate, and provide paperwork. If damaged glass is involved, Bang AutoGlass offers next-day mobile windshield replacement. Installs usually take 30-45 minutes plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
How Shops Confirm Buick Regal GS ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
Reputable shops confirm your Buick Regal GS ADAS is in-spec by following an OEM-style workflow and producing proof. First is a diagnostic pre-scan (health scan) with a capable scan tool to capture diagnostic trouble codes (DTCs), module status, and stored ADAS faults, even if no warning lights are on. Next, the shop verifies calibration prerequisites that make the result valid: correct tire size and pressure, proper ride height, no steering or suspension play, and alignment within specification (including thrust angle). Because calibrations reference vehicle geometry, an out-of-spec alignment or sagging ride height can make camera calibration or radar calibration inaccurate. With prerequisites confirmed, the shop identifies which calibrations your specific Buick Regal GS requires for the repair event (windshield replacement, bumper work, alignment, or suspension repair). Depending on OEM procedure, calibration may be static (targets set at measured distances on a level surface with controlled lighting) and/or dynamic (a scan-tool guided road routine under defined speed and lane-marking conditions). After completion, a post-scan verifies DTCs are cleared and systems report normal operation. Ask for the deliverables: pre-scan and post-scan printouts, alignment measurements when applicable, and the ADAS calibration report/certificate showing a successful final status.
Insurance and Warranty Questions for Buick Regal GS ADAS Calibration: What’s Typically Covered and What to Document
With Buick Regal GS ADAS calibration, reimbursement usually depends on the cause. Collision-related calibrations (bumper repair, sensor bracket replacement, suspension impact) are commonly billed under collision coverage. Calibrations required after windshield replacement on a Buick Regal GS with a windshield-mounted camera are often handled under comprehensive coverage, especially when the camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Deductibles and carrier rules vary, so ask whether scanning and camera/radar calibration are reimbursable for your claim. Make the decision easy for the adjuster by keeping strong documentation: a repair order stating the trigger event, photos of the affected area, alignment printouts if alignment or ride height was part of the job, and both pre-scan and post-scan results. The key document is the ADAS calibration report showing the procedure performed and the final pass status. It also helps when invoices separate glass work, diagnostic scanning, and calibration labor. Bang AutoGlass supports the glass portion with mobile service (often as soon as next day when scheduling allows) and works with all insurers when comprehensive coverage applies. Windshield replacement typically takes 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and includes a lifetime workmanship warranty.
Services
Service Areas
Do You Need ADAS Calibration for Buick Regal GS After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
On a Buick Regal GS, a wheel alignment affects more than steering feel and tire wear—it can also shift the reference angles your Advanced Driver Assistance Systems (ADAS) use for lane-keeping assist (LKA), lane departure warning (LDW), adaptive cruise control (ACC), and automatic emergency braking (AEB). These systems rely on the vehicle’s direction of travel (thrust angle) and a correct steering angle sensor (SAS) zero point to define “straight ahead.” When toe, camber, or caster is adjusted, the Buick Regal GS may track on a slightly different line, and OEM procedures often call for a SAS reset and an ADAS calibration check so the forward camera and radar match the updated geometry. Depending on requirements, that may be a static target setup, a scan-tool guided dynamic road routine, or both. After any four-wheel alignment, ask if the shop performed a diagnostic pre-scan/post-scan and documented any required camera calibration, radar calibration, or steering angle reset. Skipping steps can show up as LKA that nudges off-center, ACC that behaves inconsistently, or alerts that seem late or overly sensitive. If you’re searching “Buick Regal GS ADAS calibration after alignment” or “ADAS calibration near me,” choose a process that verifies alignment specs first and records calibration results.
Buick Regal GS ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Buick Regal GS—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Buick Regal GS set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Buick Regal GS After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
After a minor collision in a Buick Regal GS, ADAS calibration is commonly missed because the car may appear normal. However, radar and camera assemblies are aimed within very small tolerances. A low-speed rear-end, parking-lot hit, or curb strike can shift a radar bracket behind the bumper cover or disturb a camera mount by only millimeters, yet that can change how ACC, AEB, lane-keeping assist, and forward collision warning behave. It also may not set a warning light; some systems log diagnostic trouble codes that only show on a scan, while others operate with reduced accuracy until you notice phantom alerts or inconsistent following distance. A safer workflow is a diagnostic pre-scan, any manufacturer-required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status, with the calibration report saved for your records and insurance file. If the impact also caused a chipped or cracked windshield—especially on Buick Regal GS trims with windshield-mounted cameras—Bang AutoGlass can provide mobile windshield replacement when scheduling allows. Most installs take 30–45 minutes, and we recommend at least one hour of safe drive time for adhesive cure. We can also help you document what happened and connect you to an appropriate calibration resource.
Signs Your Buick Regal GS ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
If your Buick Regal GS has ADAS, a warning light for the camera, radar, or lane assist is the obvious sign calibration may be needed. Many issues show up earlier as behavior that feels "off." Notice lane-keeping assist pulling you off-center, lane departure alerts firing too often, or lane-centering that wanders instead of holding steady. Adaptive cruise control (ACC) can also change: inconsistent following distance, abrupt braking, or unexpected speed changes may mean the camera or radar view is no longer aligned with the vehicle's centerline. Other clues include false forward-collision warnings or blind-spot monitoring that misses vehicles. If this started right after windshield replacement with a windshield-mounted camera, wheel alignment, suspension/steering work, bumper repair, or a minor hit, assume calibration prerequisites shifted. The fix is a scan for codes and an OEM-procedure static and/or dynamic calibration, documented with a calibration report. For searches like "Buick Regal GS ADAS calibration near me," choose a shop that can scan, calibrate, and provide paperwork. If damaged glass is involved, Bang AutoGlass offers next-day mobile windshield replacement. Installs usually take 30-45 minutes plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
How Shops Confirm Buick Regal GS ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
Reputable shops confirm your Buick Regal GS ADAS is in-spec by following an OEM-style workflow and producing proof. First is a diagnostic pre-scan (health scan) with a capable scan tool to capture diagnostic trouble codes (DTCs), module status, and stored ADAS faults, even if no warning lights are on. Next, the shop verifies calibration prerequisites that make the result valid: correct tire size and pressure, proper ride height, no steering or suspension play, and alignment within specification (including thrust angle). Because calibrations reference vehicle geometry, an out-of-spec alignment or sagging ride height can make camera calibration or radar calibration inaccurate. With prerequisites confirmed, the shop identifies which calibrations your specific Buick Regal GS requires for the repair event (windshield replacement, bumper work, alignment, or suspension repair). Depending on OEM procedure, calibration may be static (targets set at measured distances on a level surface with controlled lighting) and/or dynamic (a scan-tool guided road routine under defined speed and lane-marking conditions). After completion, a post-scan verifies DTCs are cleared and systems report normal operation. Ask for the deliverables: pre-scan and post-scan printouts, alignment measurements when applicable, and the ADAS calibration report/certificate showing a successful final status.
Insurance and Warranty Questions for Buick Regal GS ADAS Calibration: What’s Typically Covered and What to Document
With Buick Regal GS ADAS calibration, reimbursement usually depends on the cause. Collision-related calibrations (bumper repair, sensor bracket replacement, suspension impact) are commonly billed under collision coverage. Calibrations required after windshield replacement on a Buick Regal GS with a windshield-mounted camera are often handled under comprehensive coverage, especially when the camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Deductibles and carrier rules vary, so ask whether scanning and camera/radar calibration are reimbursable for your claim. Make the decision easy for the adjuster by keeping strong documentation: a repair order stating the trigger event, photos of the affected area, alignment printouts if alignment or ride height was part of the job, and both pre-scan and post-scan results. The key document is the ADAS calibration report showing the procedure performed and the final pass status. It also helps when invoices separate glass work, diagnostic scanning, and calibration labor. Bang AutoGlass supports the glass portion with mobile service (often as soon as next day when scheduling allows) and works with all insurers when comprehensive coverage applies. Windshield replacement typically takes 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and includes a lifetime workmanship warranty.
Services
Service Areas
Do You Need ADAS Calibration for Buick Regal GS After a Wheel Alignment? When Alignment Changes Affect Cameras and Radar
On a Buick Regal GS, a wheel alignment affects more than steering feel and tire wear—it can also shift the reference angles your Advanced Driver Assistance Systems (ADAS) use for lane-keeping assist (LKA), lane departure warning (LDW), adaptive cruise control (ACC), and automatic emergency braking (AEB). These systems rely on the vehicle’s direction of travel (thrust angle) and a correct steering angle sensor (SAS) zero point to define “straight ahead.” When toe, camber, or caster is adjusted, the Buick Regal GS may track on a slightly different line, and OEM procedures often call for a SAS reset and an ADAS calibration check so the forward camera and radar match the updated geometry. Depending on requirements, that may be a static target setup, a scan-tool guided dynamic road routine, or both. After any four-wheel alignment, ask if the shop performed a diagnostic pre-scan/post-scan and documented any required camera calibration, radar calibration, or steering angle reset. Skipping steps can show up as LKA that nudges off-center, ACC that behaves inconsistently, or alerts that seem late or overly sensitive. If you’re searching “Buick Regal GS ADAS calibration after alignment” or “ADAS calibration near me,” choose a process that verifies alignment specs first and records calibration results.
Buick Regal GS ADAS Calibration After Suspension Work: Ride Height, Steering Angle Sensors, and Why Pricing Varies
Suspension or steering work on a Buick Regal GS—struts, shocks, springs, control arms, ball joints, tie rods, or steering components—often justifies an ADAS calibration check because these repairs change ride height and alignment geometry. ADAS sensors don’t “approximate” the road; they convert camera and radar views into precise angles and distances. A small change in ride height can tilt the forward camera (pitch/yaw) and alter radar aim, while changes in toe and thrust angle affect how the vehicle’s calibrated centerline matches its real path. Those mechanical shifts also influence how the steering angle sensor (SAS), yaw-rate sensor, and wheel-speed inputs are interpreted for lane-centering and ACC distance control. Many OEM workflows for a Buick Regal GS set prerequisites before recalibration: verify tire size/pressure, confirm ride height, inspect for looseness, and complete a four-wheel alignment within spec. Only then are camera calibration, radar calibration, or a steering angle reset considered valid. Pricing varies because the work varies—some trims need only a dynamic road routine, others require static targets, and some require both, plus multiple systems (front camera, front radar, blind-spot or parking sensors) to be checked. For best results, treat calibration as the final step and request the printed calibration report.
ADAS Calibration for Buick Regal GS After a Minor Collision: Even Without Visible Damage, Sensors Can Shift
After a minor collision in a Buick Regal GS, ADAS calibration is commonly missed because the car may appear normal. However, radar and camera assemblies are aimed within very small tolerances. A low-speed rear-end, parking-lot hit, or curb strike can shift a radar bracket behind the bumper cover or disturb a camera mount by only millimeters, yet that can change how ACC, AEB, lane-keeping assist, and forward collision warning behave. It also may not set a warning light; some systems log diagnostic trouble codes that only show on a scan, while others operate with reduced accuracy until you notice phantom alerts or inconsistent following distance. A safer workflow is a diagnostic pre-scan, any manufacturer-required aiming/calibration (static targets, dynamic road routine, or both), and a post-scan confirming normal module status, with the calibration report saved for your records and insurance file. If the impact also caused a chipped or cracked windshield—especially on Buick Regal GS trims with windshield-mounted cameras—Bang AutoGlass can provide mobile windshield replacement when scheduling allows. Most installs take 30–45 minutes, and we recommend at least one hour of safe drive time for adhesive cure. We can also help you document what happened and connect you to an appropriate calibration resource.
Signs Your Buick Regal GS ADAS Needs Calibration: Warning Lights, Lane-Keeping Pull, ACC Issues, and False Alerts
If your Buick Regal GS has ADAS, a warning light for the camera, radar, or lane assist is the obvious sign calibration may be needed. Many issues show up earlier as behavior that feels "off." Notice lane-keeping assist pulling you off-center, lane departure alerts firing too often, or lane-centering that wanders instead of holding steady. Adaptive cruise control (ACC) can also change: inconsistent following distance, abrupt braking, or unexpected speed changes may mean the camera or radar view is no longer aligned with the vehicle's centerline. Other clues include false forward-collision warnings or blind-spot monitoring that misses vehicles. If this started right after windshield replacement with a windshield-mounted camera, wheel alignment, suspension/steering work, bumper repair, or a minor hit, assume calibration prerequisites shifted. The fix is a scan for codes and an OEM-procedure static and/or dynamic calibration, documented with a calibration report. For searches like "Buick Regal GS ADAS calibration near me," choose a shop that can scan, calibrate, and provide paperwork. If damaged glass is involved, Bang AutoGlass offers next-day mobile windshield replacement. Installs usually take 30-45 minutes plus at least one hour of safe drive time for adhesive cure, backed by a lifetime workmanship warranty.
How Shops Confirm Buick Regal GS ADAS Is In-Spec: Pre-Scan/Post-Scan, Alignment Specs, and Calibration Reports
Reputable shops confirm your Buick Regal GS ADAS is in-spec by following an OEM-style workflow and producing proof. First is a diagnostic pre-scan (health scan) with a capable scan tool to capture diagnostic trouble codes (DTCs), module status, and stored ADAS faults, even if no warning lights are on. Next, the shop verifies calibration prerequisites that make the result valid: correct tire size and pressure, proper ride height, no steering or suspension play, and alignment within specification (including thrust angle). Because calibrations reference vehicle geometry, an out-of-spec alignment or sagging ride height can make camera calibration or radar calibration inaccurate. With prerequisites confirmed, the shop identifies which calibrations your specific Buick Regal GS requires for the repair event (windshield replacement, bumper work, alignment, or suspension repair). Depending on OEM procedure, calibration may be static (targets set at measured distances on a level surface with controlled lighting) and/or dynamic (a scan-tool guided road routine under defined speed and lane-marking conditions). After completion, a post-scan verifies DTCs are cleared and systems report normal operation. Ask for the deliverables: pre-scan and post-scan printouts, alignment measurements when applicable, and the ADAS calibration report/certificate showing a successful final status.
Insurance and Warranty Questions for Buick Regal GS ADAS Calibration: What’s Typically Covered and What to Document
With Buick Regal GS ADAS calibration, reimbursement usually depends on the cause. Collision-related calibrations (bumper repair, sensor bracket replacement, suspension impact) are commonly billed under collision coverage. Calibrations required after windshield replacement on a Buick Regal GS with a windshield-mounted camera are often handled under comprehensive coverage, especially when the camera supports lane-keeping, forward-collision warning, or automatic emergency braking (AEB). Deductibles and carrier rules vary, so ask whether scanning and camera/radar calibration are reimbursable for your claim. Make the decision easy for the adjuster by keeping strong documentation: a repair order stating the trigger event, photos of the affected area, alignment printouts if alignment or ride height was part of the job, and both pre-scan and post-scan results. The key document is the ADAS calibration report showing the procedure performed and the final pass status. It also helps when invoices separate glass work, diagnostic scanning, and calibration labor. Bang AutoGlass supports the glass portion with mobile service (often as soon as next day when scheduling allows) and works with all insurers when comprehensive coverage applies. Windshield replacement typically takes 30-45 minutes, plus at least one hour of safe drive time for adhesive cure, and includes a lifetime workmanship warranty.
Enjoy More Relevant Blogs
Mobile ADAS Calibration for Buick Regal GS: What to Expect On-Site and Why Setup Matters
Mobile ADAS calibration for Buick Regal GS: what to expect on-site, space and lighting needs, and why setup and verification matter after repairs today.
OEM Calibration Requirements for Buick Regal GS: How to Confirm What Must Be Calibrated
OEM calibration requirements for Buick Regal GS: how to confirm what must be calibrated after repairs, what triggers recalibration, and what proof to ask for.
How to Schedule ADAS Calibration for Buick Regal GS After Windshield Replacement
Schedule ADAS calibration for Buick Regal GS after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
Static vs Dynamic ADAS Calibration for Buick Regal GS: What the Difference Means
Static vs dynamic ADAS calibration for Buick Regal GS: key differences, when each is required, how long it takes, and what affects accuracy for safety.
How Much Does ADAS Calibration Cost for Buick Regal GS? What Drives Pricing and What Insurance Typically Covers
How much does ADAS calibration cost for a Buick Regal GS? Learn pricing drivers, camera vs radar needs, labor time, and what insurance typically covers.
Camera Calibration for Buick Regal GS: Lane Assist and Forward Collision Accuracy Explained
Need camera calibration for your Buick Regal GS? See how calibration affects lane assist and forward collision accuracy after windshield service or repairs.
Pre- and Post-Calibration Scans for Buick Regal GS: Proving Systems Are Set Correctly
Pre- and post-calibration scans for Buick Regal GS: see why scans matter, what they verify, and how reports prove ADAS systems are set correctly after service.
ADAS Warning Lights on Buick Regal GS: When Calibration Is the Fix and When It’s Not
ADAS warning lights on your Buick Regal GS? Learn when calibration fixes lane assist or AEB issues, when it will not, and what to check next. Schedule help.
ADAS Calibration Checklist for Buick Regal GS: Documentation, Verification, and Final Safety Checks
ADAS calibration checklist for Buick Regal GS: documentation to request, scans to verify, and safety checks that confirm cameras and sensors are set right.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm