Services
Service Areas
Tempered Safety Rear Glass Replacement for Mercedes-Benz Sprinter Worker Passenger: Understanding DOT Markings and FMVSS 205
What FMVSS 205 Covers for Mercedes-Benz Sprinter Worker Passenger Rear Glass: Safety Glazing Scope and Purpose
FMVSS 205 (49 CFR 571.205) governs motor-vehicle glazing, including the rear window glass on your Mercedes-Benz Sprinter Worker Passenger. It exists to reduce laceration risk from contact with glass, maintain the transparency drivers need for visibility, and set predictable performance expectations in crashes. The standard achieves this by incorporating ANSI/SAE Z26.1, which assigns glazing Item classifications and performance levels and specifies where each type may be installed (windshield, side, or rear). FMVSS 205 also requires each regulated piece of glass to carry permanent identification, typically a DOT symbol, an NHTSA-issued manufacturer code, and other Z26.1 markings that indicate the glazing category. For a Mercedes-Benz Sprinter Worker Passenger back glass replacement, the right part is not just the right shape; it must be certified for the rear-window location and match key options. A compliant replacement should display the required DOT and classification marks, align with the factory defroster grid and any antenna elements, and match tint or shading. Bang AutoGlass verifies the stamp and specs before installation and can provide mobile service as soon as next day. Most replacements take 30–45 minutes, plus a recommended minimum one-hour urethane cure time before safe drive-away.
Tempered Safety Rear Glass on Mercedes-Benz Sprinter Worker Passenger: What “Tempered” Means and Why It’s Used
Rear windows on a Mercedes-Benz Sprinter Worker Passenger are typically tempered safety glass, chosen for strength and controlled breakage. In manufacturing, the glass is heat-treated and quenched, leaving the surfaces in compression and the core in tension. That stress profile makes the panel stronger than annealed glass and helps it tolerate daily vibration, body flex, and minor impacts. If failure occurs, the stored stresses drive a predictable fragmentation pattern: the sheet breaks into many small, rounded pieces instead of sharp spears, reducing deep laceration risk. This is why tempered glass is favored for rear and side openings, while windshields are usually laminated to retain the glass layer after impact. Tempered rear glass also accommodates printed defroster grids, privacy shading, and on some Mercedes-Benz Sprinter Worker Passenger versions, embedded antenna lines that must align with the vehicle connectors. Because tempered glass cannot be reliably repaired after cracking, correct replacement becomes the priority. Bang AutoGlass installs tempered rear glass with attention to proper urethane adhesion, trim fitment, and the correct DOT/FMVSS safety stamp for the application. We provide mobile service as soon as next day, and every installation is supported by a lifetime workmanship warranty.
How to Read the Rear Glass Stamp: DOT Symbol, NHTSA Manufacturer Code, and Certification Marks
The etching on the back window is one of the most reliable checkpoints when replacing rear glass on a Mercedes-Benz Sprinter Worker Passenger. FMVSS 205 requires compliant glazing to be permanently marked for certification and traceability, using identifiers referenced to ANSI/SAE Z26.1. In the real world, the stamp usually shows a manufacturer name or logo, the DOT symbol, and a DOT number tied to an NHTSA manufacturer code. You may also see an AS marking, an Item code, or both, which help indicate the glazing category and permitted installation locations. For rear windows, a clear material callout such as TEMPERED or TEMP is common. Some stamps include internal part references, plant codes, and date indicators, but the core check is simple: the replacement should carry the required DOT mark and a designation appropriate for rear-window use. This matters if your Mercedes-Benz Sprinter Worker Passenger rear glass includes a printed defroster grid, embedded antenna lines, or privacy tint, because the glass must match both compliance and functional patterns. Bang AutoGlass can use a photo of your existing stamp and connectors to confirm the correct rear glass and document the replacement installed.
ANSI/SAE Z26.1 Item and AS Markings: What the Codes Indicate and Where They Can Be Used
The codes on your Mercedes-Benz Sprinter Worker Passenger rear window stamp aren’t random—they come from the ANSI/SAE Z26.1 marking system referenced by FMVSS 205. Two identifiers usually appear together. The Z26.1 “Item” designation is the performance class based on required tests and expected behavior in service and breakage. The “AS” code is the American Standard marking used for glazing identification and permitted-use guidance. Because rear openings are usually tempered safety glass, the stamp typically includes a tempered callout plus AS2 or AS3 (and sometimes an Item number). These marks matter because windows are regulated by performance and visible light transmittance, not just by fit. NHTSA interpretations commonly cite 70% light transmission as the minimum for areas “requisite for driving visibility,” while AS3 is under 70% and is limited to areas not requisite for visibility. So an incorrect AS category can create a compliance or inspection issue even if the glass physically fits. For your Mercedes-Benz Sprinter Worker Passenger, the right back glass should match the original glazing type, tint intent, and certification marks. Bang AutoGlass uses the stamp and connector layout to confirm the correct part before installation.
Ordering the Correct Mercedes-Benz Sprinter Worker Passenger Rear Glass: Defroster Grid, Antenna Lines, Tint, and Compliance Checks
Ordering the correct Mercedes-Benz Sprinter Worker Passenger rear glass is more than matching the outline. A proper rear windshield replacement must match equipment features and the compliance stamp. First, confirm model year, trim, and body style (sedan, hatchback, SUV) because those can change the glass and molding system. Next, verify functional features: a rear defroster grid, embedded antenna lines, or both. The defroster pattern and electrical tab locations must match your harness, and the right antenna layout helps prevent weak reception. Then match appearance: clear vs. privacy/solar tint and any factory color tone (often green or gray). Also confirm fitment details such as rear wiper holes, bracket points, molding profile, and the location of defroster connectors. Finally, check certification. FMVSS 205 requires replacement glazing to meet the same applicable requirements as the original, so the new glass should carry the proper DOT code and ANSI/SAE Z26.1 markings for a rear window. A quick photo of the old stamp and connector layout before removal can save time and returns. Bang AutoGlass handles these checks, sources the correct tempered safety rear glass for your Mercedes-Benz Sprinter Worker Passenger, and brings mobile auto glass replacement to your location with insurance-friendly paperwork when comprehensive coverage applies.
Documentation and Post-Install Verification: Marking Photos, Defroster Testing, and Quality Checks
Post-install verification is what turns a rear glass that “fits” into a complete Mercedes-Benz Sprinter Worker Passenger rear windshield replacement. Start with compliance documentation: FMVSS 205 requires regulated glazing to be permanently marked, so take clear photos of the old stamp before removal and the new stamp after installation. That provides proof of the DOT symbol and manufacturer code and makes part details easy to confirm later. Next, verify electrical functions before trim is buttoned up. Defrosters rely on properly bonded tabs and secure connectors, so activate the rear window defroster and confirm even warming across the grid. If your Mercedes-Benz Sprinter Worker Passenger uses embedded antenna lines, confirm connector hookup and reception to avoid surprises. Then check workmanship: centered alignment, continuous urethane contact around the perimeter, clean moldings, and a practical leak and wind-noise check after reassembly. Bang AutoGlass typically completes mobile rear glass installs in 30–45 minutes, and we advise at least one hour of cure time before normal driving. Your installation is backed by a lifetime workmanship warranty, and we streamline insurance documentation when comprehensive coverage is involved.
Services
Service Areas
Tempered Safety Rear Glass Replacement for Mercedes-Benz Sprinter Worker Passenger: Understanding DOT Markings and FMVSS 205
What FMVSS 205 Covers for Mercedes-Benz Sprinter Worker Passenger Rear Glass: Safety Glazing Scope and Purpose
FMVSS 205 (49 CFR 571.205) governs motor-vehicle glazing, including the rear window glass on your Mercedes-Benz Sprinter Worker Passenger. It exists to reduce laceration risk from contact with glass, maintain the transparency drivers need for visibility, and set predictable performance expectations in crashes. The standard achieves this by incorporating ANSI/SAE Z26.1, which assigns glazing Item classifications and performance levels and specifies where each type may be installed (windshield, side, or rear). FMVSS 205 also requires each regulated piece of glass to carry permanent identification, typically a DOT symbol, an NHTSA-issued manufacturer code, and other Z26.1 markings that indicate the glazing category. For a Mercedes-Benz Sprinter Worker Passenger back glass replacement, the right part is not just the right shape; it must be certified for the rear-window location and match key options. A compliant replacement should display the required DOT and classification marks, align with the factory defroster grid and any antenna elements, and match tint or shading. Bang AutoGlass verifies the stamp and specs before installation and can provide mobile service as soon as next day. Most replacements take 30–45 minutes, plus a recommended minimum one-hour urethane cure time before safe drive-away.
Tempered Safety Rear Glass on Mercedes-Benz Sprinter Worker Passenger: What “Tempered” Means and Why It’s Used
Rear windows on a Mercedes-Benz Sprinter Worker Passenger are typically tempered safety glass, chosen for strength and controlled breakage. In manufacturing, the glass is heat-treated and quenched, leaving the surfaces in compression and the core in tension. That stress profile makes the panel stronger than annealed glass and helps it tolerate daily vibration, body flex, and minor impacts. If failure occurs, the stored stresses drive a predictable fragmentation pattern: the sheet breaks into many small, rounded pieces instead of sharp spears, reducing deep laceration risk. This is why tempered glass is favored for rear and side openings, while windshields are usually laminated to retain the glass layer after impact. Tempered rear glass also accommodates printed defroster grids, privacy shading, and on some Mercedes-Benz Sprinter Worker Passenger versions, embedded antenna lines that must align with the vehicle connectors. Because tempered glass cannot be reliably repaired after cracking, correct replacement becomes the priority. Bang AutoGlass installs tempered rear glass with attention to proper urethane adhesion, trim fitment, and the correct DOT/FMVSS safety stamp for the application. We provide mobile service as soon as next day, and every installation is supported by a lifetime workmanship warranty.
How to Read the Rear Glass Stamp: DOT Symbol, NHTSA Manufacturer Code, and Certification Marks
The etching on the back window is one of the most reliable checkpoints when replacing rear glass on a Mercedes-Benz Sprinter Worker Passenger. FMVSS 205 requires compliant glazing to be permanently marked for certification and traceability, using identifiers referenced to ANSI/SAE Z26.1. In the real world, the stamp usually shows a manufacturer name or logo, the DOT symbol, and a DOT number tied to an NHTSA manufacturer code. You may also see an AS marking, an Item code, or both, which help indicate the glazing category and permitted installation locations. For rear windows, a clear material callout such as TEMPERED or TEMP is common. Some stamps include internal part references, plant codes, and date indicators, but the core check is simple: the replacement should carry the required DOT mark and a designation appropriate for rear-window use. This matters if your Mercedes-Benz Sprinter Worker Passenger rear glass includes a printed defroster grid, embedded antenna lines, or privacy tint, because the glass must match both compliance and functional patterns. Bang AutoGlass can use a photo of your existing stamp and connectors to confirm the correct rear glass and document the replacement installed.
ANSI/SAE Z26.1 Item and AS Markings: What the Codes Indicate and Where They Can Be Used
The codes on your Mercedes-Benz Sprinter Worker Passenger rear window stamp aren’t random—they come from the ANSI/SAE Z26.1 marking system referenced by FMVSS 205. Two identifiers usually appear together. The Z26.1 “Item” designation is the performance class based on required tests and expected behavior in service and breakage. The “AS” code is the American Standard marking used for glazing identification and permitted-use guidance. Because rear openings are usually tempered safety glass, the stamp typically includes a tempered callout plus AS2 or AS3 (and sometimes an Item number). These marks matter because windows are regulated by performance and visible light transmittance, not just by fit. NHTSA interpretations commonly cite 70% light transmission as the minimum for areas “requisite for driving visibility,” while AS3 is under 70% and is limited to areas not requisite for visibility. So an incorrect AS category can create a compliance or inspection issue even if the glass physically fits. For your Mercedes-Benz Sprinter Worker Passenger, the right back glass should match the original glazing type, tint intent, and certification marks. Bang AutoGlass uses the stamp and connector layout to confirm the correct part before installation.
Ordering the Correct Mercedes-Benz Sprinter Worker Passenger Rear Glass: Defroster Grid, Antenna Lines, Tint, and Compliance Checks
Ordering the correct Mercedes-Benz Sprinter Worker Passenger rear glass is more than matching the outline. A proper rear windshield replacement must match equipment features and the compliance stamp. First, confirm model year, trim, and body style (sedan, hatchback, SUV) because those can change the glass and molding system. Next, verify functional features: a rear defroster grid, embedded antenna lines, or both. The defroster pattern and electrical tab locations must match your harness, and the right antenna layout helps prevent weak reception. Then match appearance: clear vs. privacy/solar tint and any factory color tone (often green or gray). Also confirm fitment details such as rear wiper holes, bracket points, molding profile, and the location of defroster connectors. Finally, check certification. FMVSS 205 requires replacement glazing to meet the same applicable requirements as the original, so the new glass should carry the proper DOT code and ANSI/SAE Z26.1 markings for a rear window. A quick photo of the old stamp and connector layout before removal can save time and returns. Bang AutoGlass handles these checks, sources the correct tempered safety rear glass for your Mercedes-Benz Sprinter Worker Passenger, and brings mobile auto glass replacement to your location with insurance-friendly paperwork when comprehensive coverage applies.
Documentation and Post-Install Verification: Marking Photos, Defroster Testing, and Quality Checks
Post-install verification is what turns a rear glass that “fits” into a complete Mercedes-Benz Sprinter Worker Passenger rear windshield replacement. Start with compliance documentation: FMVSS 205 requires regulated glazing to be permanently marked, so take clear photos of the old stamp before removal and the new stamp after installation. That provides proof of the DOT symbol and manufacturer code and makes part details easy to confirm later. Next, verify electrical functions before trim is buttoned up. Defrosters rely on properly bonded tabs and secure connectors, so activate the rear window defroster and confirm even warming across the grid. If your Mercedes-Benz Sprinter Worker Passenger uses embedded antenna lines, confirm connector hookup and reception to avoid surprises. Then check workmanship: centered alignment, continuous urethane contact around the perimeter, clean moldings, and a practical leak and wind-noise check after reassembly. Bang AutoGlass typically completes mobile rear glass installs in 30–45 minutes, and we advise at least one hour of cure time before normal driving. Your installation is backed by a lifetime workmanship warranty, and we streamline insurance documentation when comprehensive coverage is involved.
Services
Service Areas
Tempered Safety Rear Glass Replacement for Mercedes-Benz Sprinter Worker Passenger: Understanding DOT Markings and FMVSS 205
What FMVSS 205 Covers for Mercedes-Benz Sprinter Worker Passenger Rear Glass: Safety Glazing Scope and Purpose
FMVSS 205 (49 CFR 571.205) governs motor-vehicle glazing, including the rear window glass on your Mercedes-Benz Sprinter Worker Passenger. It exists to reduce laceration risk from contact with glass, maintain the transparency drivers need for visibility, and set predictable performance expectations in crashes. The standard achieves this by incorporating ANSI/SAE Z26.1, which assigns glazing Item classifications and performance levels and specifies where each type may be installed (windshield, side, or rear). FMVSS 205 also requires each regulated piece of glass to carry permanent identification, typically a DOT symbol, an NHTSA-issued manufacturer code, and other Z26.1 markings that indicate the glazing category. For a Mercedes-Benz Sprinter Worker Passenger back glass replacement, the right part is not just the right shape; it must be certified for the rear-window location and match key options. A compliant replacement should display the required DOT and classification marks, align with the factory defroster grid and any antenna elements, and match tint or shading. Bang AutoGlass verifies the stamp and specs before installation and can provide mobile service as soon as next day. Most replacements take 30–45 minutes, plus a recommended minimum one-hour urethane cure time before safe drive-away.
Tempered Safety Rear Glass on Mercedes-Benz Sprinter Worker Passenger: What “Tempered” Means and Why It’s Used
Rear windows on a Mercedes-Benz Sprinter Worker Passenger are typically tempered safety glass, chosen for strength and controlled breakage. In manufacturing, the glass is heat-treated and quenched, leaving the surfaces in compression and the core in tension. That stress profile makes the panel stronger than annealed glass and helps it tolerate daily vibration, body flex, and minor impacts. If failure occurs, the stored stresses drive a predictable fragmentation pattern: the sheet breaks into many small, rounded pieces instead of sharp spears, reducing deep laceration risk. This is why tempered glass is favored for rear and side openings, while windshields are usually laminated to retain the glass layer after impact. Tempered rear glass also accommodates printed defroster grids, privacy shading, and on some Mercedes-Benz Sprinter Worker Passenger versions, embedded antenna lines that must align with the vehicle connectors. Because tempered glass cannot be reliably repaired after cracking, correct replacement becomes the priority. Bang AutoGlass installs tempered rear glass with attention to proper urethane adhesion, trim fitment, and the correct DOT/FMVSS safety stamp for the application. We provide mobile service as soon as next day, and every installation is supported by a lifetime workmanship warranty.
How to Read the Rear Glass Stamp: DOT Symbol, NHTSA Manufacturer Code, and Certification Marks
The etching on the back window is one of the most reliable checkpoints when replacing rear glass on a Mercedes-Benz Sprinter Worker Passenger. FMVSS 205 requires compliant glazing to be permanently marked for certification and traceability, using identifiers referenced to ANSI/SAE Z26.1. In the real world, the stamp usually shows a manufacturer name or logo, the DOT symbol, and a DOT number tied to an NHTSA manufacturer code. You may also see an AS marking, an Item code, or both, which help indicate the glazing category and permitted installation locations. For rear windows, a clear material callout such as TEMPERED or TEMP is common. Some stamps include internal part references, plant codes, and date indicators, but the core check is simple: the replacement should carry the required DOT mark and a designation appropriate for rear-window use. This matters if your Mercedes-Benz Sprinter Worker Passenger rear glass includes a printed defroster grid, embedded antenna lines, or privacy tint, because the glass must match both compliance and functional patterns. Bang AutoGlass can use a photo of your existing stamp and connectors to confirm the correct rear glass and document the replacement installed.
ANSI/SAE Z26.1 Item and AS Markings: What the Codes Indicate and Where They Can Be Used
The codes on your Mercedes-Benz Sprinter Worker Passenger rear window stamp aren’t random—they come from the ANSI/SAE Z26.1 marking system referenced by FMVSS 205. Two identifiers usually appear together. The Z26.1 “Item” designation is the performance class based on required tests and expected behavior in service and breakage. The “AS” code is the American Standard marking used for glazing identification and permitted-use guidance. Because rear openings are usually tempered safety glass, the stamp typically includes a tempered callout plus AS2 or AS3 (and sometimes an Item number). These marks matter because windows are regulated by performance and visible light transmittance, not just by fit. NHTSA interpretations commonly cite 70% light transmission as the minimum for areas “requisite for driving visibility,” while AS3 is under 70% and is limited to areas not requisite for visibility. So an incorrect AS category can create a compliance or inspection issue even if the glass physically fits. For your Mercedes-Benz Sprinter Worker Passenger, the right back glass should match the original glazing type, tint intent, and certification marks. Bang AutoGlass uses the stamp and connector layout to confirm the correct part before installation.
Ordering the Correct Mercedes-Benz Sprinter Worker Passenger Rear Glass: Defroster Grid, Antenna Lines, Tint, and Compliance Checks
Ordering the correct Mercedes-Benz Sprinter Worker Passenger rear glass is more than matching the outline. A proper rear windshield replacement must match equipment features and the compliance stamp. First, confirm model year, trim, and body style (sedan, hatchback, SUV) because those can change the glass and molding system. Next, verify functional features: a rear defroster grid, embedded antenna lines, or both. The defroster pattern and electrical tab locations must match your harness, and the right antenna layout helps prevent weak reception. Then match appearance: clear vs. privacy/solar tint and any factory color tone (often green or gray). Also confirm fitment details such as rear wiper holes, bracket points, molding profile, and the location of defroster connectors. Finally, check certification. FMVSS 205 requires replacement glazing to meet the same applicable requirements as the original, so the new glass should carry the proper DOT code and ANSI/SAE Z26.1 markings for a rear window. A quick photo of the old stamp and connector layout before removal can save time and returns. Bang AutoGlass handles these checks, sources the correct tempered safety rear glass for your Mercedes-Benz Sprinter Worker Passenger, and brings mobile auto glass replacement to your location with insurance-friendly paperwork when comprehensive coverage applies.
Documentation and Post-Install Verification: Marking Photos, Defroster Testing, and Quality Checks
Post-install verification is what turns a rear glass that “fits” into a complete Mercedes-Benz Sprinter Worker Passenger rear windshield replacement. Start with compliance documentation: FMVSS 205 requires regulated glazing to be permanently marked, so take clear photos of the old stamp before removal and the new stamp after installation. That provides proof of the DOT symbol and manufacturer code and makes part details easy to confirm later. Next, verify electrical functions before trim is buttoned up. Defrosters rely on properly bonded tabs and secure connectors, so activate the rear window defroster and confirm even warming across the grid. If your Mercedes-Benz Sprinter Worker Passenger uses embedded antenna lines, confirm connector hookup and reception to avoid surprises. Then check workmanship: centered alignment, continuous urethane contact around the perimeter, clean moldings, and a practical leak and wind-noise check after reassembly. Bang AutoGlass typically completes mobile rear glass installs in 30–45 minutes, and we advise at least one hour of cure time before normal driving. Your installation is backed by a lifetime workmanship warranty, and we streamline insurance documentation when comprehensive coverage is involved.
Enjoy More Relevant Blogs
Rear Defroster Not Working on Mercedes-Benz Sprinter Worker Passenger? When Rear Glass Replacement Makes More Sense Than Repair
Rear defroster not working on your Mercedes-Benz Sprinter Worker Passenger? Learn common causes, when repair fails, and when rear glass replacement is the smarter fix for winter.
How Much Does Rear Glass Replacement Cost for Mercedes-Benz Sprinter Worker Passenger? Pricing Factors, OEM vs Aftermarket, and Insurance Deductibles
Estimate Mercedes-Benz Sprinter Worker Passenger rear glass replacement cost. Compare OEM vs aftermarket, labor factors, insurance deductibles, and ways to save. Request a quote.
Post-Install Checks for Mercedes-Benz Sprinter Worker Passenger: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Mercedes-Benz Sprinter Worker Passenger: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Back Glass Replacement on Mercedes-Benz Sprinter Worker Passenger: Defroster Tabs, Antenna Lines, and Connector Reattachment Basics
Back glass replacement on Mercedes-Benz Sprinter Worker Passenger: defroster tabs, antenna lines, and connectors explained, plus install tips to avoid damage and rework safely.
How Long Does Rear Glass Replacement Take on Mercedes-Benz Sprinter Worker Passenger? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How long is Mercedes-Benz Sprinter Worker Passenger rear glass replacement? Get install time, urethane cure guidelines, and drive-away timing after service. Plan your visit today.
OEM-Quality Rear Glass Replacement for Mercedes-Benz Sprinter Worker Passenger: Defroster Grid and Tint-Match Checklist
OEM-quality rear glass replacement for Mercedes-Benz Sprinter Worker Passenger: defroster grid and tint-match checklist, plus install tips to avoid callbacks—schedule service.
Shattered Back Window on Mercedes-Benz Sprinter Worker Passenger: A Step-by-Step Rear Glass Replacement Plan
Shattered back window on Mercedes-Benz Sprinter Worker Passenger? Follow a step-by-step rear glass replacement plan, cleanup tips, defroster notes, cure time, and drive-away rules.
How to Schedule Mobile Rear Glass Replacement for Mercedes-Benz Sprinter Worker Passenger
Schedule mobile rear glass replacement for your Mercedes-Benz Sprinter Worker Passenger in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Rear Glass Replacement for Mercedes-Benz Sprinter Worker Passenger: What to Expect During Install and Aftercare
Rear glass replacement for Mercedes-Benz Sprinter Worker Passenger: what happens during install, defroster and tint considerations, cure time, and aftercare to prevent leaks long-term.
Bang AutoGlass
Quick Links
Services
Service Areas
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Service Areas
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Service Areas
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm